FUJI错误代码查询.pdf - 第211页

Code: 11081031 Display: Part Carrier Cycle alarm Used by: MTU4 Cause: When the parts supply carrier advances or retracts, the advance end and retract end sensors do not come on. Remedy: Check that the position of the sen…

100%1 / 5282
Display: DxShell timeout.
Used by: NP2,QP3
Cause: The operation command to the parts supply unit was not processed within the required time.
Remedy: Press READY ON to continue processing, or reboot the machine if this is not effective.
------------------------------
Code: 1107D00E
Display: Parts Supply Unit Error
Used by: QP301
Cause: Abnormal software process occurred.
Remedy: Turn off the power and reboot.Contact Fuji if this error occurs frequently.
------------------------------
Code: 1107D00F
Display: Parts Supply Unit Error
Used by: QP301
Cause: No connection with parts supply unit specified in the recipe or communication with the unit fai
led.
Remedy: Connect the parts supply unit and then reperform association processing.
------------------------------
Code: 1107D010
Display: Feeder Error
Used by: QP301
Cause: No feeder in the slot specified in the recipe or no communication with the feeder.
Remedy: Check the feeder positions and reperform association processing if required.
------------------------------
Code: 11081000
Display: EMERGENCY STOP
Used by: MTU3,MTU4,MTU5
Cause: The emergency stop button was pressed at either the machine or the MTU.
Remedy: Release the emergency stop button at either the machine or the MTU.
------------------------------
Code: 11081010
Display: Servo alarm
Used by: MTU3,MTU4,MTU5
Cause: There is a problem with one of the MTU servo axes.
Remedy: Check that no load is applied to the axes.
------------------------------
Code: 11081011
Display: Order alarm
Used by: MTU3,MTU4,MTU5
Cause: A servo axis has exceeded the soft limit set in Proper data or due to a wiring fault etc, the 200 V
power supply is off.
Remedy: If this error occurred during inching, switch on the servo from the MTU panel and using inching
return the axis to a suitable position. In other cases, check that there are no problems with the wiring in
the control box and the wiring to the sensors.
------------------------------
Code: 11081020
Display: Safety door is open
Used by: MTU3,MTU4,MTU5
Cause: The safety door is open.
Remedy: Close the safety door.
------------------------------
第 210 页
Code: 11081031
Display: Part Carrier Cycle alarm
Used by: MTU4
Cause: When the parts supply carrier advances or retracts, the advance end and retract end sensors do
not come on.
Remedy: Check that the position of the sensors has not shifted. Check that there are no anomalies in the
carrier drive motor and actuator. Power may not be supplied to the carrier drive motor controller. In that
case switch on the power.
------------------------------
Code: 11081032
Display: T Axis Cycle alarm
Used by: MTU4
Cause: When the T axis (the tray) moved it did not reach its target position.
Remedy: Check that there are no problems in the T axis servo system and that the various connectors are
correctly connected.
------------------------------
Code: 11081033
Display: X Axis Cycle alarm
Used by: MTU3,MTU4,MTU5
Cause: When the X axis moved it did not reach its target position.
Remedy: Check that there are no problems in the X axis servo system and that the various connectors are
correctly connected.
------------------------------
Code: 11081034
Display: Y Axis Cycle alarm
Used by: MTU3,MTU4,MTU5
Cause: When the Y axis moved it did not reach its target position.
Remedy: Check that there are no problems in the Y axis servo system and that the various connectors are
correctly connected.
------------------------------
Code: 11081035
Display: Z Axis Cycle alarm
Used by: MTU3,MTU4,MTU5
Cause: When the Z axis moved it did not reach its target position.
Remedy: Check that there are no problems in the Z axis servo system and that the various connectors are
correctly connected.
------------------------------
Code: 11081036
Display: Parts Conveyor Cycle alarm
Used by: MTU3,MTU5
Cause: When the parts conveyor axis moved it did not reach its target position.
Remedy: Check that there are no problems in the parts conveyor axis servo system and that the various
connectors are correctly connected.
------------------------------
Code: 11081041
Display: Overtravel: Check X+ Axis
Used by:
Cause: The X axis + overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the X axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item max_limit_sx.
------------------------------
第 211 页
Code: 11081042
Display: Overtravel: Check X- Axis
Used by: MTU3,MTU4,MTU5
Cause: The X axis - overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the X axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item min_limit_sx.
------------------------------
Code: 11081043
Display: Overtravel: Check Y+ Axis
Used by: MTU3,MTU4,MTU5
Cause: The Y axis + overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the Y axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item max_limit_sy.
------------------------------
Code: 11081044
Display: Overtravel: Check Y- Axis
Used by: MTU3,MTU4,MTU5
Cause: The Y axis - overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the Y axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item min_limit_sy.
------------------------------
Code: 11081045
Display: Overtravel: Check Z+ Axis
Used by: MTU3,MTU4,MTU5
Cause: The Z axis + overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the Z axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item max_limit_sz.
------------------------------
Code: 11081046
Display: Overtravel: Check Z- Axis
Used by: MTU3,MTU4,MTU5
Cause: The Z axis - overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the Z axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item min_limit_sz.
------------------------------
Code: 11081047
Display: Overtravel: Check T+ Axis
Used by: MTU4
Cause: The T axis + overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the T axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item max_limit_t.
------------------------------
Code: 11081048
Display: Overtravel: Check T- Axis
Used by: MTU4
Cause: The T axis - overtravel sensor is on, or the software limit has been exceeded.
Remedy: Move the T axis to a point before the overtravel sensor or to a point inside the position set in the
Proper data item min_limit_t.
------------------------------
Code: 11081049
Display: Software limit: Check X
第 212 页