FUJI错误代码查询.pdf - 第617页

Cause: System error. Remedy: Cut the power and reboot the machine. If the problem recurs, contact Fuji. ------------------------------ Code: 12063024 Display: Used by: Cause: Even though the head was not over the screen,…

Display:

Used by: GSP5,GP551,GP6

Cause: When the Y- or Z-axis is moving, it interferes with the board holder. Alternately, the board holder

interlock sensor is not working correctly.

Remedy: Retract the board holder so that it does not interfere with the camera station. Also, check the

interlock sensor.

------------------------------

Code: 1206301D

Display:

Used by: GSP5

Cause: The board and the mask expansion rate exceeds the production program's elongation_limit item.

Remedy: Increase the value of the elongation_limit in the production program or change the mask and

board. Alternately, set elongation_limit to 0 and this item will be disabled.

------------------------------

Code: 1206301E

Display:

Used by: GSP5,GP2,GP3

Cause: The screen position compensation was carried out, but the pulse motor moved more than the

value allowed in the Proper data item Max Limit Position ***.

Remedy: Check the mark coordinates in the program. Adjust the screen frame spacers. Check that the

Proper data item Max Limit Position is not set to 0.

------------------------------

Code: 1206301F

Display:

Used by:

Cause: Process timeout occurred during communication.

Remedy: Contact Fuji if this happens frequently.

------------------------------

Code: 12063020

Display:

Used by:

Cause: The stocker data set signal was output, but no reply was received.

Remedy: Check the wiring. Check that the stocker sequencer is operating correctly.

------------------------------

Code: 12063021

Display:

Used by:

Cause: A command was sent to the stocker communication unit but a response was not received within

the specified time limit.

Remedy: Check the wiring. If this error occurs frequently, check the machine version and the stocker

ROM version, and contact Fuji.

------------------------------

Code: 12063022

Display:

Used by: GSP5,GP2,GP3,GP551,GP6

Cause: Communication could not be carried out with the printing measurement machine.

Remedy: Check the wiring between the terminal and the printing measurement machine.

------------------------------

Code: 12063023

Display:

Used by: GSP5

第 616 页

Cause: System error.

Remedy: Cut the power and reboot the machine. If the problem recurs, contact Fuji.

------------------------------

Code: 12063024

Display:

Used by:

Cause: Even though the head was not over the screen, an attempt was made to execute the solder

discharge command.

Remedy: Inch the head over the metal portion of the screen and execute the solder discharge command.

------------------------------

Code: 12063025

Display: Interlock Z

Used by: GSP5

Cause: The camera station may collide with the main table.

Remedy: Inch the Z-axis close to its zero set position (the position at which the Z-axis origin sensor,

Z_AXIS_ZERO, turns on).

------------------------------

Code: 12063026

Display: XL XR Interlock

Used by:

Cause: The L camera and R camera proximity sensor was activated

Remedy: Separate the L and R cameras either manually or by inching.

------------------------------

Code: 12063027

Display: Obstruction In Screen Path

Used by:

Cause: Stencil transport was not possible because of an obstruction in the stencil transport path.

Remedy: Remove the obstruction.

------------------------------

Code: 12063028

Display: 请拆下网板

[Please Screen Release]

Used by: GP551,GP6,GPX,NXTP

Cause: 现在，网板正处于夹紧中。在更换支架时有网板的情况下发生。存在网板框 (GPX)

Remedy: 请松开网板(指令页 558(2)「松开」)，然后拆下。请将网板框取出。（GPX)

------------------------------

Code: 12063029

Display: "Please Cleaner escape"

Used by: GP551,GP6

Cause: This error occurs if the holder is changed while the cleaner is not at the origin position.

Remedy: Move the cleaner to the origin position (the position at which X05C:CLNR ZERO POS" shows a

value of 0). If necessary, make sure that the lower cleaner origin position check sensor (X05C:CLNRZERO

POS) is functioning normally.

------------------------------

Code: 1206302A

Display: "Cleaner Did Not Connect"

Used by: GP551,GP6

Cause: This error may occur if an attempt is made to close the cleaner head while the connection status

between the cleaner and the cleaner drive axis is inappropriate: either the cleaner notch that connects the

cleaner to the drive axis was not inserted, or the cleaner is not proximate to the drive axis. This error may

第 617 页

also occur if the cleaner notch is out even though the cleaner was not at the escape position.

Remedy: In the former instance, use [HEAD ATTACHMENT] on command page 553-2(4) to properly

connect the cleaner to the drive axis. If necessary, make sure that the lower cleaner connection check

sensor and the cleaner connection position proximity check sensor (X05D:LW CLR CPL CHK and

X03E:CLNR NEAR CHK) are functioning normally. In the latter case, manually return the cleaner to the

origin position.

------------------------------

Code: 1206302B

Display: "Cleaner Sandwich Position Out of Range"

Used by: GP6

Cause: This error occurs if an attempt is made to close the cleaner head while the cleaner is at an

inappropriate position. The cleaner is either at the origin or outside the cleaning range.

Remedy: Move the cleaner inside the cleaning range. On a double-side cleaner, the cleaning range is

between the positions set by the following Proper data parameters: "222:Max Limit Position S clnr"and

"223:Min Limit Position S clnr." On a single-side cleaner, it is between the positions set by the following

Proper data parameters: "232:Max Limit Position Y clnr" and "233:Min Limit PositionY clnr."

------------------------------

Code: 1206302C

Display: "Cleaner Notch Action Error"

Used by: GP6

Cause: Removal of the cleaner notch required longer than the specified time. This error may also occur if

the cleaner notch is in even though the cleaner is not proximate to the cleaner drive axis (the Y-axis for a

double-side cleaner, or the S-axis for a single-side cleaner).

Remedy: Use I/O commands to check the sensor. If necessary, return the cleaner to the proper status.

------------------------------

Code: 1206302D

Display: "Cleaner XY catch"

Used by: GP6

Cause: Removal of the notch connecting the single-side cleaner to the XY-axis required longer than the

specified time.

Remedy: Use I/O commands to check the sensor.

------------------------------

Code: 1206302E

Display: "Move SQG Start Position at Printing"

Used by: GP551,GP6

Cause: This error occurs if automatic operation is started with the double squeegee positioned inside the

printing area.

Remedy: Move the squeegee outside the printing area, either to the front or rear side.

------------------------------

Code: 1206302F

Display: 请除去印刷状态不明的电路板

[Printing Not Possible. Remove Board]

Used by: GPX,NXTP

Cause: 判断出主搬运轨道的电路板正处在印刷途中。印刷途中的电路板不能够印刷。

Remedy: 请除去主搬运轨道的电路板，修正后，从ＩＮ搬运轨道处载入。

------------------------------

Code: 12063030

Display: "Univ holder at inner limit"

Used by: GP551,GP6

Cause: Board holder interference occurred while changing the conveyor width. This error occurs when

第 618 页