FUJI错误代码查询.pdf - 第1194页

than the part size. As a rule, the size of the black plate attached to chucks is entered at that setting item. ------------------------------ Code: 1CA??016 Display: 1CA??016 Used by: Cause: The Vision_type in part data …

Remedy: If "??" equals 1E, 64, 78, 79, AC or FE then either the nozzle center of rotation does not conform

with the image of the nozzle or the image lies outside of the scan area. Make sure the nozzle is not bent.

Or in the case that the image lies outside of the camera field of vision, enlarge the scan area. If "??" equals

7C, 82, 83, 98, 9D or B4 this signifies that the body could not be distinguishedor separated from the

leads. Input the Lead_brightness in part data. If "??" equals 8C, E6, E7 or E9 there are too ew leads

described in part data and the positioning phase could not be carried out. Correct the part data. If "??"

equal F0, F1 or F2 then check the model size. Create a model to reduce the size of the circumscribed

square outline for the entire model.

------------------------------

Code: 1CA??012

Display: 1CA??012

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 1E, 64,

78, 79, AC, or FE this signifies that the image of the part that has been found is smaller than thesize of

the nozzle. If "??" equals 8C, E6, E7, or E9 then the part is too big.

No license key is required when ?? = F1 or F2.

Remedy: If "??" equals 1E, 64, 78, 79, AC, or FE then either the image of the part that has been found is

smaller than the size of the nozzle or the image lies outside of the field of vision. Make sure the correct

nozzle has been specified. Or in the case that the image lies outside of the camera field of vision, enlarge

the scan area. If "??" equals 8C, E6, E7, or E9 then a valid field of vision cannot be acquired since the

part size is too big.

When ?? = F1 or F2, confirm that there is a license key, or that the license key is operating properly.

------------------------------

Code: 1CA??013

Display: 1CA??013

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 82, 83, 8D, 8E, 98, 9D or B4 this indicates that the leads could not be acquired from the body and

background. If "??" equals 8C, E6, E7, or E9 then no leads exist.

Remedy: If "??" equals 7B, 7C, 82, 83, 8D, 8E, 98, 9D or B4 this signifies that the body could not be

distinguished or separated from the leads. Input the Lead_brightness in part data. If "??" equals 8C, E6,

E7, or E9 this indicates that not a single lead was reflected. Make sure that the image has been acquired

properly.

------------------------------

Code: 1CA??014

Display: 1CA??014

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 82, 83, 98 or B4 this signifies that the threshold value request was improper. If "??" equals 8C, E6 or

E7 then the body size has not been input in part data. If "??" equal 8D or 8E then the body size is

incorrect.

Remedy: If "??" equals 7B, 7C, 82, 83, 98, or B4 this is an internal error that normally does not occur. If

"??" equals 8C, E6, E7 or E9 then input the correct data in part data. If "??" equal 8D or 8E then the

specified body size exceeds the tolerance value registered in part data. Check the body size.

------------------------------

Code: 1CA??015

Display: 1CA??015

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 7B, 7C,

98 or b4 then part search area is incorrect.

Remedy: If "??" equal 7B, 7C, 98 or b4 then check to see if a nozzle size was registered which is larger

第 1193 页

than the part size. As a rule, the size of the black plate attached to chucks is entered at that setting item.

------------------------------

Code: 1CA??016

Display: 1CA??016

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 8D or

8E then the image cannot be converted to binary data.Remedy: If "??" equal 8D or 8E then this is a highly

unusual internal error. Contact your Fuji service representative if this error occurs.

Remedy:

------------------------------

Code: 1CA??017

Display: 1CA??017

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 8D or

8E then processing is not possible because the space between bumps is too narrow.

Remedy: If "??" equal 8D or 8E then use a bump array where the distance between the bumps (leads) is

1/6 or more of the average vertical and horizontal body size.

------------------------------

Code: 1CA??021

Display:

Used by:

Cause: ?? is the PD Vision_type in hexadecimal numbers. If ?? = 64, 69, 78, 79, 7A, 7D, 7E, or 7F ,the

coarse position cannot be determined. If ?? = 7B, 7C, 80, 81, 82, 83, 87, 88, 8C, E6, E7, E9, EB, EC, 98,

or 9D, less than half the specified leads were found. If ?? = 99, part cannot be found.

Remedy: If ?? = 64, 69, 78, 79, 7A, 7D, 7E, or 7F ,check that there is no problem with image brightness,

and check that there is no problem with a dirty background. If ?? = 7B, 7C, 80, 81, 82, 83, 87, 88, 8C,

E6, E7, E9, EB, EC, 98, or 9D, check for errors in the part data. In particular, check the lead size data. If

?? = 99, the part which should be detected cannot be found. Check to see if the part appears on the

image display.

------------------------------

Code: 1CA??022

Display: 1CA??022

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 8C, E6, E7, E9, EB, EC, 98, or 9D fewer than half of the leads specified in part data could be found. If

"??" equal 8D or 8E then part position cannot be determined because fewer than 2 bumps were found.

Remedy: If ?? is 7B, 7C, 80, 81, 82, 83, 87, 8C, E6, E7, E9, EB, EC, 98, or 9D check the part data,

especially the number of leads and the lead size. If "??" equal 8D or 8E then check the part data. Also

check to see if the bump sizes are correct. Or, increase the bump size tolerance value.

------------------------------

Code: 1CA??023

Display: 1CA??023

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 88, 98, or B4 the blob area is incorrect.

Remedy: This is an internal processing error which should not normally occur. If this error occurs, notify

Fuji.

------------------------------

Code: 1CA??024

Display: 1CA??024

Used by:

第 1194 页

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 88, 98, 9D or B4 the specified number of leads could not be found.

Remedy: Check the part data, especially the lead size.

------------------------------

Code: 1CA??025

Display: 1CA??025

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 88, 98, 9D or B4 extra leads have been found.

Remedy: Check that the part data is correct.

------------------------------

Code: 1CA??030

Display: 1CA??030

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E or F0 this signifies that the segments such as the leads

that should have been measured do not exist.

Remedy: In this case the Result data item in EL_data of part data was set to "0" for all of the elements.

Set the Result data item to "1" for all measured segments.

------------------------------

Code: 1CA??031

Display: 1CA??031

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, AA, or F0 this indicates that lead inspection could not

be carried out. If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, or 98 then the input parameters are incorrect.

If "??" equals 8C, E6, E7, E9, EB, or EC this signifies that the part angle was not found. If "??" equal B4

excessive mismatch between data and actual part was found.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, AA or F0 then the lead

inspection has failed for some reason. Make sure that there are no mistakes in the EL_data in part data.

If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, or 98 this is an internal error that normally does not occur.

If it does occur contact Fuji. If "??" equals 8C, E6, E7, E9, EB, or EC then too many leads were not found

making it impossible to determine the angle. Make sure that the part data is correct and in particular

check the size of the leads. If "??" equal B4 check for errors in the part data. In particular, check lead

information.

------------------------------

Code: 1CA??032

Display: 1CA??032

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, or F0 this indicates that there was no inspected

segment for determining the X-dimension of the part position. If "??" equals 7B, 7C, 80, 81, 82, 83, 87,

88, 98, or 9D then the correct part angle was not found. If "??" equals 8C, E6, E7, E9, EB, or EC this

indicates that the part positioning phase could not be carried out. If "??" 8D or 8E equals coarse

positioning cannot be performed.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, or F0 this means that

the inspection of leads has failed for some reason. Leads could not be found for the X-dimension

inspection results to be used for part positioning. Make sure that the data set in P_pattern in part data is

appropriate. If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, 98, or 9D then make sure that the part data is

correct and in particular that the lead size setting matches the actual size of the leads. If "??" equals 8C,

E6, E7, E9, EB, or EC then the external ow of leads could not be detected. Check the part data and if the

第 1195 页