FUJI错误代码查询.pdf - 第139页

Code: 1101F024 Display: 用于检测钢网插入方向的Mark点读取异常 Used by: GPX-C Cause: 不能读取用于检测钢网插入方向的Mark点。 Remedy: 请确认钢网的插入方向。 ------------------------------ Code: 1101F025 Display: 脱模等待时间超出范围 Used by: NXTP、GPXC Cause: 脱模等待时间超出范围 Remedy: …

Cause: 电路板尺寸X超范围。

Remedy: 电路板尺寸X的允许设置范围受钢网尺寸影响。

------------------------------

Code: 1101F01D

Display: 电路板尺寸Y超范围。

Used by: GPXC

Cause: 电路板尺寸Y超范围。

Remedy: 电路板尺寸Y的允许设置范围受钢网尺寸影响。

------------------------------

Code: 1101F01E

Display: 不对应指定的钢网类型。

Used by: GPXC

Cause: 指定的钢网类型无法使用。

Remedy: ·Flexa中的设定：[Process Option]-[Screen]-[Screen Type]可以选用的钢网类型会因机器的Hard

Option设定[650mm frame support]的不同而不同。如需变更[650mm frame support]的设定，则需要对机器进行

改造。)

------------------------------

Code: 1101F01F

Display: 电路板停止位置X超范围。

Used by: NXTP、GPX、GPXC

Cause: 电路板停止位置X超范围。

Remedy: ·Flexa内的设定：[Process Option]-[Panel Stop]-[Position X] 正向送板时：-[电路板尺寸X] ～

2.00mm　　逆向送板时： -2.00mm ～ [电路板尺寸X]

------------------------------

Code: 1101F020

Display: 电路板停止位置Y超范围。

Used by: NXTP、GPX、GPXC

Cause: 电路板停止位置Y超范围。

Remedy: ·Flexa内的设定：[Process Option]-[Panel Stop]-[Position Y]

------------------------------

Code: 1101F021

Display: 钢网的Offset超范围。

Used by: NXTP、GPX、GPXC

Cause: 钢网的Offset超范围。

Remedy: ·Flexa内的设定：[Process Option]-[Screen]-[Origin Offset]

------------------------------

Code: 1101F022

Display: Mesh Size超范围

Used by: NXTP、GPX、GPXC

Cause: Mesh Size超范围

Remedy: ·Flexa内的设定：[Process Option]-[Screen]-[Mesh Size]

------------------------------

Code: 1101F023

Display: 用于检测进板方向的Mark点读取异常

Used by: GPX-C

Cause: 不能读取用于检测进板方向的Mark点。

Remedy: 请确认进板方向。

------------------------------

第 138 页

Code: 1101F024

Display: 用于检测钢网插入方向的Mark点读取异常

Used by: GPX-C

Cause: 不能读取用于检测钢网插入方向的Mark点。

Remedy: 请确认钢网的插入方向。

------------------------------

Code: 1101F025

Display: 脱模等待时间超出范围

Used by: NXTP、GPXC

Cause: 脱模等待时间超出范围

Remedy: Flexa的设置中Process Option - Print Procedure - Snap-off wait time

的设置范围为0 - 10000[msec]。

------------------------------

Code: 1101F026

Display: 读取定位点类型异常。

Used by: GPX-C,GPX-CS

Cause: 读取定位点类型不合适。

Remedy: 请在生产程序编辑中将读取定位点类型变更为以下中的某一个。·补正用定位点 ·方向检查用定位点 ·无

法读取的定位点

------------------------------

Code: 1101F027

Display: 定位点数据下载失败。

Used by: NXTP,GPX-C,GPX-CS

Cause: 定位点数据下载失败。

Remedy: 请确认定位点的设定。关于引发异常的可能原因，请参考如下。

·未向机器分配定位点。

·分配了实际不存在的定位点名。

请执行数据确认并确认有无异常（要求：无异常）。

------------------------------

Code: 1101F028

Display: 定位点数量不合理。

Used by: NXTP,GPX-C,GPX-CS

Cause: 定位点数量不合理。

Remedy: 请确认下列条件。

·Fiducial定位点和Mask定位点的数量都不得少于2个且个数必须相同。

·定位点数量上限

Fiducial定位点和Mask定位点的坐标相同时→ 8个

Fiducial定位点和Mask定位点的坐标不一致时→ 4个

·是否向机器分配了定位点？

请执行数据确认并确认有无异常（要求：无异常）。

------------------------------

Code: 1101F029

Display:

Used by:

Cause:

Remedy:

------------------------------

Code: 11022001

Display: 11022001

Used by:

Cause: The "Language" setting is out of the range.

第 139 页

Remedy: Check the setting for Language in the Proper data at the MCS, and retransmit the Proper data.

Select either English, French, or Japanese. As French is currently not supported, English will display if

French is selected.

------------------------------

Code: 11022002

Display:

Used by: CP4-1,CP4-2,CP4-3,CP6,CP6N,CP65,CP652C,CP642,CP643,IP2,IP3

Cause: The Proper "Device Check Port" is out of range.

Remedy: Check Proper data's "Device Check Port." When using the optional Handy Terminal this must be

set. Normally, to avoid communication board jumper setting problems, this is set to "1." This is the first

connector from the top of the board. This is set before the machine is delivered.

------------------------------

Code: 11022003

Display:

Used by: IP3

Cause: Device check terminal (ex.: Handy Terminal) communication port has been previously specified

elsewhere.

Remedy: Specify the correct value in Proper data's 73.Device Check port.

------------------------------

Code: 11022004

Display:

Used by: IP3,QP132

Cause: Verifier tool is not set correctly.

Remedy: Specify the correct value in Proper data's 71.Verifier Tool.

------------------------------

Code: 11022005

Display:

Used by: IP3,QP132

Cause: The device check is specified to operate but the device check terminal is set to not operate, and

both ESC Permission and MAN Permission are set to "Non."

Remedy: If the device check is specified to operate but the device check terminal is set to not operate,

either 74.ESC Permission or 75.MAN Permission must be set to "Permit." Alternately, specify that the

device check not be used, or specify that a device check terminal be used.

------------------------------

Code: 11022006

Display: 11022006

Used by: GSP5

Cause: The Proper data cannot be transmitted because the MCS version is old.

Remedy: The machine software version has been upgraded to include additions to the Proper data and

therefore it is not compatible with the present version of MCS. Upgrade the MCS software. As a

temporary measure, return the machine to the original software version until the upgraded version of MCS

is received.

------------------------------

Code: 11022007

Display: Same as code.

Used by: SECS/GEM

Cause: The bit setting in "Machine_status A" (fourth bit from the right) which enables remote commands

is set to "0" or the value for the item "LMS_flag" is set to "0".

Remedy: Ensure that both of these are set to "1" when using SECS/GEM.

------------------------------

Code: 11022300

第 140 页