FUJI错误代码查询.pdf - 第1887页
------------------------------ Code: 21005901 Display: Now edttting data is not Squence data Used by: Cause: The cut command was used on data which was not sequence data. Remedy: Only use the cut command on sequence data…
Used by:
Cause: Either no data was entered into the paste buffer or the paste command tried put the data into a
different field.
Remedy: Data can only be pasted into the same field.
------------------------------
Code: 21005705
Display: Copy line is record field over
Used by:
Cause: The data exceeded the range of the field during copying. (Data is recorded up to the range of the
field.)
Remedy: Sufficient space is allowed for data so this problem should seldom occur. Field size cannot be
changed at this point, so make sure it is correct beforehand.
------------------------------
Code: 21005706
Display: Data entry error
Used by:
Cause: The data entry was out of range.
Remedy: Check the input data.
------------------------------
Code: 21005801
Display: Digitizer not found
Used by:
Cause: The digitizer is not registered in the line descriptor.
Remedy: Register the digitizer (Mc_type=18) in the editor (line descriptor) and re-boot the system. Refer to
the operation manual, Part 2, Sections 1,2 and 3 for details.
------------------------------
Code: 21005802
Display: Digitizer time out error
Used by:
Cause: Nothing was received from the digitizer within the specified time limit.
Remedy: Check that the cable and connector is properly connected. Perform the self-test on port RS
232C.
------------------------------
Code: 21005803
Display: Digitizer data error
Used by:
Cause: The data from the digitizer is out of range.
Remedy: Check the range of entry.
------------------------------
Code: 21005811
Display: file name error
Used by:
Cause: The filename is longer than 19 characters. This number includes appendages such as ".exp."
Remedy: Shorten it.
------------------------------
Code: 21005900
Display: Now editting data is not Programe data
Used by:
Cause: The cut command was used on data which was not in the production program or the source
program.
Remedy: Do not use the cut command on data which is not in the production program or source program.
第 1886 页
------------------------------
Code: 21005901
Display: Now edttting data is not Squence data
Used by:
Cause: The cut command was used on data which was not sequence data.
Remedy: Only use the cut command on sequence data.
------------------------------
Code: 21005902
Display: Cut number syntax error
Used by:
Cause: In the cut command "0" or "1" was used. The cut command must use the number "2" or greater.
Remedy: The cut command erases all the sequence data lines greater than the number input. Input "2"
or greater. In sequence data, at least one line is necessary.
------------------------------
Code: 21005903
Display: Input sequence NO. not found.
Used by:
Cause: The sequence number does not exist.
Remedy: Check the sequence data and re-execute the sequence.
------------------------------
Code: 21005950
Display: Edit command not execute
Used by:
Cause: The sub-editor could not handle the overflow.
Remedy: At a terminal there can be up to 2 editors. If a new editor has been opened, try again after
closing the sub-editor.
------------------------------
Code: 21006000
Display: Illegal parameter
Used by:
Cause: The parameter is illegal.
Remedy: Check the parameter.
------------------------------
Code: 21006001
Display: message file read error
Used by:
Cause: The message file could not be read.
Remedy: Re-install the separator software.
------------------------------
Code: 21006002
Display: console pipe open error
Used by:
Cause: Unable to open the console pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21006003
Display: CRT semaphore link error
Used by:
Cause: The CRT semaphore ID could not be obtained.
Remedy: Re-boot MCS.
------------------------------
第 1887 页
Code: 21006004
Display: separator pipe create error
Used by:
Cause: Unable to create the separator pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21006005
Display: Permanent Set Table name get error
Used by:
Cause: The permanent set table name could not be read from the environment variable file.
Remedy: Check the permanent set table.
------------------------------
Code: 21006006
Display: Special Conditions File name get error
Used by:
Cause: The name specified for the Special Conditions File could not be read from the environment
variables file.
Remedy: Check the Special conditions file.
------------------------------
Code: 21006007
Display: Off-line Descriptor get error
Used by:
Cause: The name specified for the off-line descriptor could not be read from the environment variables
file.
Remedy: Check the off-line descriptor.
------------------------------
Code: 21006008
Display: line name get error
Used by:
Cause: The name specified for the line name could not be read from the environment variables file.
Remedy: Check the line descriptor.
------------------------------
Code: 21006009
Display: generate switch get error
Used by:
Cause: The generate switch could not be read from the environment variables file.
Remedy: Check the environment variables file.
------------------------------
Code: 2100600A
Display: object disk name get error
Used by:
Cause: The object disk could not be read from the environment variables file.
Remedy: Check the environment variables file.
------------------------------
Code: 2100600B
Display: output file name get error
Used by:
Cause: The output file could not be read from the environment variables file.
Remedy: Check the environment variables file.
------------------------------
Code: 2100600C
第 1888 页