FUJI错误代码查询.pdf - 第165页

3 = Tamura VPS Reflow oven. 4 = Koki Reflow oven. 5 = Senju Reflow Oven. Do not use ------------------------------ Code: 11022900 Display: Used by: IP3 Cause: Origin_Position_X has no value specified. Remedy: Input an ap…

100%1 / 5282
Display: 11022715
Used by:
Cause: During HELPS operation, the Reader_type in Proper data is set to a value other than 0 when the
board type report for LMS is manual terminate.
Remedy: Retransmit Proper data after setting Reader_type in Proper data to 0.
------------------------------
Code: 11022716
Display: Same as code
Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP642M,CP643,CP643M
Cause: A value other than "30" has been specified at Proper data item "change_over_mode", even though
Proper data item "reader_type is set to "4". Or, a value other than "4" has been specified at Proper data
item "reader_type", even though Proper data item "change_over_mode" is set to "30".
Remedy: Check Proper data items "reader_type" and "change_over_mode".
------------------------------
Code: 11022800
Display:
Used by:
Cause: When Proper data was checked, there was no Proper for the peripgerals.
Remedy: Transmit the Proper data for the peripherals.
------------------------------
Code: 11022801
Display:
Used by:
Cause: Machine_type is set incorrectly.
Remedy: After checking the Machine_type setting in MCS, re-transmit the Proper data to the machine.
1 = flip station.
2 = input terminal.
3 = output terminal.
4 = intermediate buffer.
5 = board stacker.
7 = MBID.
8 = ferris wheel feeder.
------------------------------
Code: 11022802
Display:
Used by:
Cause: Machine_control_port is set incorrectly.
Remedy: After checking the Machine_control_port setting, re-transmit the Proper to the machine. When
machine_control_mode is set at 2~5, a setting must be made for MBID. This setting connects the next
production stage and the RS-232C cable to the LCU connector (connector number 1~8).
Do not use the settings 1, 3 or those chosen for Command_line_port, Reader1_port, Reader2_port or
Code_terminal_port. Normally setting 7 is used. This is set when the machine is shipped.
------------------------------
Code: 11022803
Display:
Used by:
Cause: Machine_control_mode is set incorrectly.
Remedy: After checking Machine_control_mode in MCS, re-transmit the Proper data.
0 = outside MBID.
1 = working display.
2 = Research MP-4470 Reflow oven.
第 164 页
3 = Tamura VPS Reflow oven.
4 = Koki Reflow oven.
5 = Senju Reflow Oven.
Do not use
------------------------------
Code: 11022900
Display:
Used by: IP3
Cause: Origin_Position_X has no value specified.
Remedy: Input an appropriate value in Proper data's 100.Origin_Position_X item.
------------------------------
Code: 11022901
Display:
Used by: IP3
Cause: Origin Position Y has not been specified.
Remedy: Specify a value in Proper data item 100.Origin_Position_Y.
------------------------------
Code: 11022902
Display:
Used by: IP3
Cause: Nozzle position X1 has no data value specified.
Remedy: Input the offset pulse value from the mark camera center to nozzle 1 in the X direction. For the
FLT, input a value in 102.Nozzle_Position_X and for the IP3, input a value in 102.Nozzle1_Position_X.
------------------------------
Code: 11022903
Display:
Used by: IP3
Cause: Nozzle position X2 (offset pulse) has no data entered.
Remedy: Input the offset pulse value from the mark camera center to nozzle 2 in the X direction. For the
IP3, input a value in 103.Nozzle2_Position_X.
------------------------------
Code: 11022904
Display:
Used by: IP3
Cause: The vision processing camera 1 position has not been specified.
Remedy: Measure the pulse values from the center of the mark camera to the center of vision processing
camera 1. Input this value into 103.Camera1_Position_X for the FLT and 104.Camera1_Position_X for the
FIP3.
------------------------------
Code: 11022905
Display:
Used by: IP3
Cause: The vision processing camera 2 position has not been specified.
Remedy: Measure the pulse values from the center of the mark camera to the center of vision processing
camera 2. Input this value into 104.Camera2_Position_X for the FLT and 105.Camera2_Position_X for the
FIP3.
------------------------------
Code: 11022906
Display:
Used by:
Cause: The 1st pin check camera (#1) position has not been specified.
第 165 页
Remedy: Measure the pulse values from the center of the mark camera to the center of the 1st pin check
camera(#1). Input this value into 111.IC_Mark_Camera_Pos.X for the FLT and
112.IC_Mark1_Camera_Pos.X for the FIP3.
------------------------------
Code: 11022907
Display:
Used by:
Cause: The 1st pin check camera (#2) position has not been specified.
Remedy: Measure the pulse values from the center of the mark camera to the center of the 1st pin check
camera(#2). Input this value into 114.IC_Mark2_Camera_Pos.X for the FIP3.
------------------------------
Code: 11022908
Display:
Used by: IP3
Cause: No reflow position value has been input.
Remedy: Measure the pulse value obtained from measuring the distance from the placing nozzle (after
zero setting) to the center of rotation of the reflow head. Input this into Proper data item
113.Reflow_Position_X for the FLT.
------------------------------
Code: 11022909
Display:
Used by: IP3
Cause: The distance from placing nozzle 1 to the board surface has not been specified.
Remedy: Specify the pulse count of the distance from the position of nozzle 1 (after zero setting) to the
surface of the board. Input this into Proper data item 123.Origin_Position_Z for the FLT and
130.Origin_Position_Z1 for the FIP3.
------------------------------
Code: 1102290A
Display:
Used by: IP3
Cause: The distance from placing nozzle 2 to the board surface has not been specified.
Remedy: Specify the pulse count of the distance from the position of nozzle 1 (after zero setting) to the
surface of the board. Input this into Proper data item 131.Origin_Position_Z1 for the FIP3.
------------------------------
Code: 1102290B
Display:
Used by:
Cause: The carrier position Z1 position has not been specified even though carrier 1 is supposed to pick
parts from MTU1.
Remedy: Input the pulse count of the Z1 axis at the picking position of carrier 1. For the FLT, use
124.Carrier_Position_Z. For the FIP3, use 132.Carrier_Position_Z1.
------------------------------
Code: 1102290C
Display:
Used by:
Cause: The carrier position Z2 position has not been specified even though carrier 2 is supposed to pick
parts from MTU2.
Remedy: Input the pulse count of the Z2 axis at the picking position of carrier 2. For the FIP3, use
132.Carrier_Position_Z1.
------------------------------
Code: 1102290D
第 166 页