FUJI错误代码查询.pdf - 第1880页

Cause: A file required by the Editor could not be opened. Remedy: The necessary files in the editor could not be opened. Re-install the editor software. If the problem persists contact Fuji. -----------------------------…

100%1 / 5282
Display: Pipe create error
Used by:
Cause: Unable to create jobcon pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21003F70
Display: Line descriptor read error
Used by:
Cause: Unable to read the line descriptor.
Remedy: Re-boot MCS.
------------------------------
Code: 21003F80
Display: M/C_No. pipe_No. Transmit channel create error
Used by:
Cause: Unable to open a monitor lead pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21003F90
Display: Login_Users link error
Used by:
Cause: The event link was opened incorrectly.
Remedy: Re-boot MCS.
------------------------------
Code: 21003FA0
Display: Pipe open error
Used by:
Cause: Unable to open Mother pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21003FA1
Display: Pipe open error
Used by:
Cause: Unable to open transmit controller pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21003FA2
Display: Pipe open error
Used by:
Cause: Unable to open pr pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21005001
Display: Editer Discriptor open error
Used by:
Cause: A necessary file could not be opened while operating the editor.
Remedy: The direct startup command entered at the UCI menu was inappropriate so input again. If this
was entered through the command function keys, re-install the software.
------------------------------
Code: 21005002
Display: File discriptor open error
Used by:
第 1879 页
Cause: A file required by the Editor could not be opened.
Remedy: The necessary files in the editor could not be opened. Re-install the editor software. If the
problem persists contact Fuji.
------------------------------
Code: 21005003
Display: Message file open error
Used by:
Cause: A message file required by the Editor could not be opened.
Remedy: A file required by the editor could not be opened by the editor. Re-install the editor software. If
the problem persists contact Fuji.
------------------------------
Code: 21005101
Display: File open error.
Used by:
Cause: When the Editor was being started up, the specified file could not be opened.
Remedy: The specified file was not created by the editor, so it could not be specified. Specify a separate
file.
------------------------------
Code: 21005102
Display: file write error
Used by:
Cause: File could not be written.
Remedy: Check whether the file write protector is on.
------------------------------
Code: 21005103
Display: Invalid filename
Used by:
Cause: An invalid filename was used.
Remedy: Input a valid filename.
------------------------------
Code: 21005104
Display: Disk_drive not ready
Used by:
Cause: The disk drive has not been prepared.
Remedy: The floppy disk has not been set. Check the floppy disk.
------------------------------
Code: 21005105
Display: Reading file; can't execute command yet.
Used by:
Cause: The edit file is reading the memory.
Remedy: The command cannot be executed until the edit file finishes reading the memory.
------------------------------
Code: 21005200
Display: can't execute command
Used by:
Cause: The command just given does not exist.
Remedy: Check the input command, and re-input.
------------------------------
Code: 21005201
Display: syntax error
Used by:
第 1880 页
Cause: There was a syntax error.
Remedy: Check the command and try to input it again.
------------------------------
Code: 21005301
Display: Comment must be enclosed by quotation marks (") in direct co
Used by:
Cause: Comments entered when setting the command must be enclosed in quotation marks.
Remedy: Enclose comments in quotation marks.
------------------------------
Code: 21005302
Display: Nickname must be enclosed by quotation marks (") in direct c
Used by:
Cause: A comment not enclosed in quotation marks (") was found when the [end] command was
executed.
Remedy: Insert quotation marks before and after the comment.
------------------------------
Code: 21005303
Display: END command not selected
Used by:
Cause: The F6 [execute] key was pressed before specifying the method of ending the Editor.
Remedy: Select the end method with the cursor keys before pressing the [execute] key.
------------------------------
Code: 21005304
Display: Number of Device data lines is incorrect
Used by:
Cause: When copying in editor or using insert_line, the number of device data lines is incorrect so the
machine attempted to save the file.
Remedy: After altering the number of device data lines to the correct number, save the file.
------------------------------
Code: 21005305
Display: File already exists
Used by:
Cause: The specified file already exists.
Remedy: Either save the file by overwriting whatever is on the other file or change the filename.
------------------------------
Code: 21005306
Display: Now edit file record count over Not execute File save
Used by:
Cause: The file size is too big and cannot be saved.
Remedy: Change the file so that it is within the specified size.
------------------------------
Code: 21005308
Display: file saving error
Used by:
Cause: The temporary file already exists.
Remedy: Turn off the computer power and re-boot the computer.
------------------------------
Code: 21005309
Display: Data checker not execute. (data type error)
Used by:
Cause: An attempt was made to perform file save and data check on items not in the program, Proper
第 1881 页