FUJI错误代码查询.pdf - 第1107页

Code: 1503100F Display: 确认电路板通过失败。 Used by: XP141,XP241,XP341,XP142,XP242 Cause: 确认电路板通过失败。 Remedy: 请确认电路板在搬运途中是否被钩住。 请确认MAIN通过传感器是否正常地动作。 ------------------------------ Code: 15031010 Display: 向次工序的电路板搬运失败。 Used by: XP1…

100%1 / 5282
Cause: The quantity of boards in the in-loader (the in-lifter and the in-carrier) cannot be ascertained
during flushout operation.
Remedy: Turn the machine off,then on again.
------------------------------
Code: 15031008
Display: IN搬运轨道的升降台上升失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: IN搬运轨道的升降台上升失败。
Remedy: IN搬运轨道的升降台未上升时，请确认通过升降台的配管是否脱离。
上升时，请确认IN升降台上升确认传感器是否正常地动作。
------------------------------
Code: 15031009
Display: IN搬运轨道的升降台下降失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: IN搬运轨道的升降台下降失败。
Remedy: 请确认IN升降台上升确认传感器是否正常地动作。请确认通过升降台的配管是否脱离。
------------------------------
Code: 1503100A
Display: MAIN搬运轨道的升降台上升失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: MAIN搬运轨道的升降台上升失败。
Remedy: MAIN搬运轨道的升降台未上升时，请确认通过升降台的配管是否脱离。
上升时，请确认MAIN升降台上升以及下降确认传感器是否正常地动作。
------------------------------
Code: 1503100B
Display: MAIN搬运轨道的升降台下降失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: MAIN搬运轨道的升降台下降失败。
Remedy: MAIN搬运轨道的升降台未下降时，请确认通过升降台的配管是否脱离。
请确认MAIN升降台上升以及下降确认传感器是否正常地动作。
------------------------------
Code: 1503100C
Display: MAIN搬运轨道的阻挡块上升失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: MAIN搬运轨道的阻挡块上升失败。
Remedy: MAIN搬运轨道的阻挡块未上升时，请确认通过升降台的配管是否脱离。
请确认阻挡块上升确认传感器是否正常地动作。
------------------------------
Code: 1503100D
Display: MAIN搬运轨道的阻挡块下降失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: MAIN搬运轨道的阻挡块下降失败。
Remedy: 请确认阻挡块上升确认传感器是否正常地动作。请确认通过阻挡块的配管是否脱离。
------------------------------
Code: 1503100E
Display: 向MAIN搬运轨道的电路板到达传感器的电路板搬运失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: 向MAIN搬运轨道的电路板到达传感器的电路板搬运失败。
Remedy: 请确认电路板在搬运途中是否被钩住。
请确认MAIN到达传感器是否正常地动作
------------------------------
第 1106 页
Code: 1503100F
Display: 确认电路板通过失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: 确认电路板通过失败。
Remedy: 请确认电路板在搬运途中是否被钩住。
请确认MAIN通过传感器是否正常地动作。
------------------------------
Code: 15031010
Display: 向次工序的电路板搬运失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: 向次工序的电路板搬运失败。
Remedy: 请确认电路板在搬运途中是否被钩住。
请确认从次工程来的要求电路板信号是否正常地动作。
------------------------------
Code: 15031011
Display: 向MAIN搬运轨道的电路板减速传感器的电路板搬运失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: 向MAIN搬运轨道的电路板减速传感器的电路板搬运失败。
Remedy: 请确认电路板在搬运途中是否被钩住。
请确认电路板减速信号是否正常地动作。
------------------------------
Code: 15031012
Display: IN搬运轨道的电路板搬运失败。
Used by: XP141,XP241,XP341,XP142,XP242
Cause: IN搬运轨道的电路板搬运失败。
Remedy: 请确认电路板是否正常地运行至IN搬运轨道到达传感器。
请确认从前工程来的可以搬运电路板信号(X018:PcbAvailable)是否正常地动作。
------------------------------
Code: 15031013
Display: 搬运轨道宽度与前工序不一致。
Used by: XP142,XP242
Cause: 搬运轨道宽度与前工序不一致。
Remedy: ·请确认前工序和本机器的搬运轨道宽度。
·搬运轨道宽度没有问题时，请确认＋跟踪确认传感器(X059)、以及、－跟踪确认传感器(X05A)是否正常地动
作。
·＋跟踪确认传感器(X059)、以及、－跟踪确认传感器(X05A)未安装的机器上，请设定固有值「
__ConveyorFollowCheck」为"0"。
------------------------------
Code: 15031014
Display: 在IN升降台下降后IN平台电路板到达确认传感器没作出反应。
Used by: XP142,XP143,XP242,XP243
Cause: 在IN升降台下降后IN平台电路板到达确认传感器没作出反应。
Remedy: 请确认IN平台的电路板的位置是否在IN平台电路板到达确认传感器作出反应的位置。
请确认IN平台电路板到达确认传感器在正常工作。
------------------------------
Code: 15032002
Display: IN-car for/bck lmt both OFF
Used by: CP643
Cause: The in-carrier extended sensor and retracted sensor are both OFF.
Remedy: Check the in-carrier extended sensor (LX01C) and the in-carrier retracted sensor (LX01D). if the
carrier is stopped between the sensors,move the in-carrier either forward or backward.
第 1107 页
------------------------------
Code: 15032003
Display: IN-car for/bck lmt both ON
Used by: CP643
Cause: The in-carrier extended sensor and retracted sensor are both ON.
Remedy: Check the in-carrier extended sensor (LX01C) and the in-carrier retracted sensor (LX01D).
------------------------------
Code: 15032004
Display: IN-car clp limits both OFF:extended limit
Used by: CP643
Cause: The in-carrier extended limit claws closed sensors and the in-carrier extended limit claws opened
sensors are both OFF.
Remedy: Check the in-carrier extended limit claws closed sensors (LX042,LX043)
and the in-carrier extended limit claws opened sensors (LX046,LX047). if the in-carrier clamp is stopped
between the sensors,either open or close the in-carrier.
------------------------------
Code: 15032005
Display: IN-car clp limits both ON:extended limit
Used by: CP643
Cause: The in-carrier extended limit claws closed sensors and the in-carrier extended limit claws opened
sensors are both ON.
Remedy: Check the in-carrier extended limit claws closed sensors (LX042,LX043)
and the in-carrier extended limit claws opened sensors (LX046,LX047).
------------------------------
Code: 1503200A
Display: OUT-car for/bck lmt both OFF
Used by: CP643
Cause: The out-carrier extended sensor and retracted sensor are both OFF.
Remedy: Check the out-carrier extended sensor (LX03C) and the out-carrier retracted sensor (LX03D). if
the carrier is stopped between the sensors,move the in-carrier either forward or backward.
------------------------------
Code: 1503200B
Display: OUT-car for/bck lmt both ON
Used by: CP643
Cause: The out-carrier extended sensor and retracted sensor are both ON.
Remedy: Check the out-carrier extended sensor (LX03C) and the out-carrier retracted sensor (LX03D).
------------------------------
Code: 1503200C
Display: OUT-car clp limits both OFF:extended limit
Used by: CP643
Cause: The out-carrier extended limit claws closed sensors and the out-carrier extended limit claws
opened sensors are both OFF.
Remedy: Check the out-carrier extended limit claws closed sensors (LX048,LX049)and the out-carrier
extended limit claws opened sensors (LX04C,LX04D). if the out-carrier clamp is stopped between the
sensors,either open or close the out-carrier.
------------------------------
Code: 1503200D
Display: OUT-car clp limits both ON:extended limit
Used by: CP643
Cause: The out-carrier extended limit claws closed sensors and the out-carrier extended limit claws
opened sensors are both ON.
第 1108 页