FUJI错误代码查询.pdf - 第1072页
Display: I/D_Conv Time up Check I/D_conveyor Used by: CP3,GL2,GSP2,GSP3,IP1 Cause: A board is caught on the ID conveyor. Remedy: Send the caught board through. Check that the ID conveyor's board detection sensor is …
Remedy: Check all the appropriate sensors. Remove the board from the machine.
------------------------------
Code: 13010025
Display: CHECK PCB_Y in HEADER
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,Cp65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP6,IP1,IP3,Q
P242,QP201
Cause: The chosen board conveyor width for the following board and the PCB_Y heading are too large.
Remedy: Inspect the PCB_Y heading. Check that the current conveyor width is correct. Use the
command keys [SET], [SERVO] and [C WIDTH] to check or adjust the conveyor width.
------------------------------
Code: 13010026
Display: CHECK FOLLOWER LMS OT
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,Cp65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP6,IP1,IP3,Q
P242,QP201
Cause: The conveyor width overtravel sensor was activated.
Remedy: Check the board width, or check the follow-up sensor.
------------------------------
Code: 13010027
Display: Check Notch
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL5,GL541,GSP5,GP2,GP3,GP6,IP1,IP3,QP242,QP201
Cause: When the machine attempted to change the conveyor width setting, either the notch did not fit, or
the notch was not removed when conveyor width adjustment finished.
Remedy: Check that the notch advances and retracts using the I/O borad. Check that each conveyor
width is correct.
------------------------------
Code: 13010028
Display: Check Backup Pin
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP5,GP2,GP3,GP6,IP1,IP3,QP242,QP201
Cause: The backup pin was detected while the conveyor width was being set.
Remedy: Check the backup pin.
------------------------------
Code: 13010029
Display: CONV Adjust Time Up
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP6,IP1,IP3,Q
P242,QP201
Cause: The conveyor did not reach its target width during the preset time allowed for adjustment.
Remedy: Check the conveyor width adjustment motor, and check the encoder.
------------------------------
Code: 1301002A
Display: Conveyor Adjust Is Not Permitted
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL5,GL541,GSP5,GP2,GP3,GP6,IP3,QP242,QP201
Cause: Permission is not given to adjust the conveyor width.
Remedy: Check that all the conditions required for permission to be given have been fulfilled.
------------------------------
Code: 1301002C
第 1071 页
Display: I/D_Conv Time up Check I/D_conveyor
Used by: CP3,GL2,GSP2,GSP3,IP1
Cause: A board is caught on the ID conveyor.
Remedy: Send the caught board through. Check that the ID conveyor's board detection sensor is
operating correctly.
------------------------------
Code: 1301002D
Display: WARNING: Check Push Plate
Used by: GSP2,GSP3
Cause: The board lifter has not been removed.
Remedy: Remove the board lifter.
------------------------------
Code: 1301002E
Display: WARNING: Check Vacuum plate
Used by: GSP2,GSP3
Cause: The board holder has not been removed.
Remedy: Remove the board holder.
------------------------------
Code: 1301002F
Display:
Used by:
Cause: The board holder could not be clamped.
Remedy: Clamp the board holder. Alternately, remove the board holder and check the sensor (IN3-24
REMOVE_S_PLATE).
------------------------------
Code: 13010030
Display: Sectional Transmitting... (PROG NAME)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP551,GP6,IP
1,IP3,QP242,QP201
Cause: The program could not be changed while part of the reservation program was being transmitted.
Remedy: Wait until the section is transmitted, and then either re-execute the function or transmit the
reservation program.
------------------------------
Code: 13010031
Display: Sectional Transmit Error (PROG NAME)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,IP1,IP2,IP3,QP
242,QP201
Cause: The reservation program was invalid due to a transmission error, so the program could not be
changed.
Remedy: Re-transmit the reservation program.
------------------------------
Code: 13010032
Display: "Family Board Error"
Used by: QP242,QP201
Cause: When performing a seamless changeover using a pilot board, the production order table specified
a production program with either a different family board name or a different board width (QP2).
Remedy: Change the production order table.
------------------------------
Code: 13010033
第 1072 页
Display: "Multiple pilot board Error"
Used by: QP242,QP201
Cause: The machine contains two or more pilot boards at one time. This error might also be caused by a
malfunction of the sensor that detects pilot boards.
Remedy: Remove the pilot board from the ICM side of the first placing module, then feed it back into the
machine after all the boards currently in the machine have been fed out.
------------------------------
Code: 14010000
Display: Image Process Time Over
Used by: GL2,GL5,GSP2,GSP3,IP1
Cause: The vision processing could not be carried out within the preset time limit.
Remedy: Check mark_data.
------------------------------
Code: 14010001
Display: err0001
Used by: GL2,GL5,GSP2,GSP3,IP1
Cause: The color of the first search point is the color specified in the Black/White item but the edge of
the mark (the border between the mark color and base color) could not be found.
Remedy: Check the CCD level and the program Mark data.
------------------------------
Code: 14010002
Display: err0002
Used by: GL2,GL5,GSP2,GSP3,IP1
Cause: The color of the first search point is the color specified in the Black/White item but the edge of
the mark (the border between the mark color and base color) does not form a closed shape.
Remedy: Check the CCD level and the program Mark data.
------------------------------
Code: 14010003
Display: err0003
Used by: GL2,GL5,GSP2,GSP3,IP1
Cause: The color of the first search point is not the color specified in the Black/White item and the edge
of the mark ( the border between the mark color and base color) could not be found.
Remedy: Check the CCD level and the program Mark data.
------------------------------
Code: 14010004
Display: err0004
Used by: GL2,GL5,GSP2,GSP3,IP1
Cause: The color of the first search point is the color specified in the Black/White item but the edge of
the mark (the border between the mark color and base color) does not form a closed shape.
Remedy: Check the CCD level and the program Mark data.
------------------------------
Code: 14010005
Display: err0005
Used by: GL2,GL5,GSP2,GSP3,IP1
Cause: An area with the opposite color of the mark was discovered but no mark could be found.
Remedy: Check the CCD level and the program Mark data.
------------------------------
Code: 14010006
Display: err0006
Used by: GL2,GL5,GSP2,GSP3,IP1
Cause: An area with the opposite color of the mark was discovered but no mark could be found.
第 1073 页