FUJI错误代码查询.pdf - 第1089页

the cancel stopper sensor. ------------------------------ Code: 15010204 Display: Conv. PLC Alarm: MCID PCB Transport Error:MCID Deceleration sensor does not turn on Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3,CP643 Cause: R…

Display: PCB Transport Error: Prev.

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: The time required to transport the board between each conveyor exceeded the preset limit. The

appropriate setting is made (1:ON 2:OFF 3:OFF). Three seconds after the deceleration point is activated

the board start point is not on, an alarm occurs and the machine is stopped.

Remedy: Check that there is no board stuck between this point and the previous production stage.

------------------------------

Code: 15010102

Display: PCB Stopper Error: Prev.

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: Stopper alarm. (1:OFF 2:ON 3:OFF) The stopper between each conveyor produced a cycle alarm.

This occurs when the time setting between the leading edge and the leaving edge is not on. After the

stopper moves vertically, the stopper vertical movement check sensor does not activate within 5 seconds to

check the position of the board stopper.

Remedy: Check for obstacles hindering stopper movement. If these obstacles (such as a board) exist,

remove them. If there are no obstacles, check the movement of the stopper at the I/O display, and check

the cancel stopper sensor.

------------------------------

Code: 15010103

Display: Command Error: Prev.

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: The operator has attempted to unload or change boards when there is no board. The operator

has attempted to load a board when there is already a board. If there was a board on the conveyor the

machine attempted to load the board. If there was no board, the machine attempted to clear off the board.

Remedy: Use the correct command based on conditions. Check that the command you are using can be

carried out under current conditions. Also, check the conveyor board arrival confirmation sensor at the

I/O dsiplay.

------------------------------

Code: 15010104

Display: Conv. PLC Alarm: Prev.

Used by: CP5,CP643,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: The CPU module (board loader PLC) is not operating normally. The user cannot set this.

Remedy: Contact Fuji.

------------------------------

Code: 15010201

Display: PCB Transport Error: MCID

Chk brd conveyance at MCID

Used by: CP5,CP6,CP6M,CP65,CP642,CP643,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: The time required to transport the board between the MCID conveyors exceeded the preset limit.

The appropriate removal setting between conveyors is made (1:ON 2:OFF 3:OFF).

Remedy: Check that there is no board stuck between this point and the previous production stage.

------------------------------

Code: 15010202

Display: PCB Stopper Error: MCID

Used by: CP5,CP6,CP6M,CP65,CP642,CP643,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: Stopper alarm. (1:OFF 2:ON 3:OFF) The stopper between each conveyor produced a cycle alarm.

This occurs when the time setting between the leading edge and the leaving edge is not on. After the

stopper moves vertically, the stopper vertical movement check sensor does not activate within 5 seconds to

check the position of the board stopper.

Remedy: Check for obstacles hindering stopper movement. If these obstacles (such as a board) exist,

remove them. If there are no obstacles, check the movement of the stopper at the I/O display, and check

第 1088 页

the cancel stopper sensor.

------------------------------

Code: 15010204

Display: Conv. PLC Alarm: MCID

PCB Transport Error:MCID

Deceleration sensor

does not turn on

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3,CP643

Cause:

Remedy:

------------------------------

Code: 15010301

Display: PCB Transport Error: IN-A

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: The time required to transport the board between each conveyor exceeded the preset limit. The

appropriate setting is made (1:ON 2:OFF 3:OFF). Three seconds after the deceleration point is activated

the board start point is not on, an alarm occurs and the machine is stopped.

Remedy: Check that there is no board stuck between this point and the previous production stage.

------------------------------

Code: 15010302

Display: PCB Stopper Error: IN-A

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: Stopper alarm. (1:OFF 2:ON 3:OFF) The stopper between each conveyor produced a cycle alarm.

This occurs when the time setting between the leading edge and the leaving edge is not on. After the

stopper moves vertically, the stopper vertical movement check sensor does not activate within 5 seconds to

check the position of the board stopper.

Remedy: Check for obstacles hindering stopper movement. If these obstacles (such as a board) exist,

remove them. If there are no obstacles, check the movement of the stopper at the I/O display, and check

the cancel stopper sensor.

------------------------------

Code: 15010303

Display: Command Error: IN-A

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: The operator has attempted to unload or change boards when there is no board. The operator

has attempted to load a board when there is already a board. If there was a board on the conveyor the

machine attempted to load the board. If there was no board, the machine attempted to clear off the board.

Remedy: Use the correct command based on conditions. Check that the command you are using can be

carried out under current conditions. Also, check the conveyor board arrival confirmation sensor at the

I/O dsiplay.

------------------------------

Code: 15010304

Display: Conv. PLC Alarm: IN-A.

Used by: CP5,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: The CPU module (board loader PLC) is not operating normally. The user cannot set this.

Remedy: Contact Fuji.

------------------------------

Code: 15010401

Display: PCB Transport Error: IN

PCB Transport Error:I_LIFT

Chk brd conveyance at I-lif

Used by: CP4-1,CP4-2,CP4-

第 1089 页

3,CP5,CP6,CP6M,CP65,CP642,CP643,GL5,GL541,GSP5,GP2,GP3,GP551,GP6,IP3

Cause: Too much time elapsed waiting for the board to be received on the in conveyor. The board may

have been removed. (I/O 1:ON, 2:OFF, 3:OFF)

The in-conveyor failed to convey a board (or boards) correctly.

Remedy: Check that the board has not become stuck on the conveyor.

Check the in-conveyor width.

Make sure the in-conveyor board sensors (the I/O input signals listed below) correctly detect the presence

of boards on the conveyor. The board gap sensor should be ON when there is no boards,and OFF when a

board is present.

I/O input signals(CP643):

LX003: IN1 board deceleration start point sensor

LX004: IN1 board arrival sensor

LX007: IN1/IN2 board gap sensor

LX008: IN2 board deceleration start point sensor

LX009: IN2 board arrival sensor

LX017: IN-conveyor board load sensor

------------------------------

Code: 15010402

Display: PCB Stopper Error : IN

PCB Stopper Error:I_LIFT

Check board-stopper up/down sensors on the I_LIFT

Used by: CP4-1,CP4-2,CP4-

3,CP5,CP6,CP6M,CP65,CP643,GL5,GL541,GSP5,GP2,GP3,GP551,GP6,IP3,NXTP

Cause: Stopper alarm (I/O 1:OFF, 2:ON, 3:OFF). This is a stopper cycle alarm for the stopper between

each conveyor. This error includes the cases where the sensor is not on for the regulated time during

engagement or disengagement. The sensor that checks that the stopper has moved up (disengaged) or

down (engaged) 5 seconds after it moves up or down does not work.

The in-conveyor mid-stopper engaged,but the engaged limit sensor did not turn ON within the specified

time.

The in-conveyor mid-stopper disengaged,but the disengaged limit sensor did not turn ON within the

specified time.

The in-conveyor mid-stopper engaged and disengaged limit sensors both ON.

Remedy: Check the conditions under which the stopper moves. If there is an interfering object (like a

board), remove it. If there is no interfering object, use the I/O to check the stopper engagement and

disengagement sensor.

Make sure the in-conveyor mid-stopper engages and disengages smoothly.

Make sure the engaged and disengaged limit sensors have been attached at the correct positions.

Make sure the engaged and disengagedlimit sensors (the I/O input signals listed

below) turn ON and OFF.

Make sure the engaged and disengagedlimit sensors (the I/O input signals listed

below) turn ON and OFF correctly when the in-conveyor mid-stopper is engaged and disengaged.

I/O input signals(CP643):

LX005: IN-conveyor mid-stopper engaged(up) limit sensor

LX006: IN-conveyor mid-stopper disengaged(down) limit sensor

------------------------------

Code: 15010403

Display: Command Error : IN

PCB Setting Error:I_LIFT

Chk brd status on in-lifter

Used by: CP5,CP6,CP6M,CP65,CP642,CP643,GSP5,GP2,GP3,GP551,GP6,IP3

第 1090 页