FUJI错误代码查询.pdf - 第1278页

uneven. There is foreign matter stuck to the part. Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not stuck to the parts. ------------------------------ Code: 1D04003A Dis…

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04002A

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04002B

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04002C

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04002D

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04002E

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04002F

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

第 1277 页

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04003A

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D04003B

Display:

Used by:

Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too

uneven. There is foreign matter stuck to the part.

Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not

stuck to the parts.

------------------------------

Code: 1D040041

Display:

Used by:

Cause: The lead cannot be found. The pitch was too wide or there were not enough leads.

Remedy: Check that the nozzle is not dirty and that there are no foreign particles on the part. Check that

the correct part is being picked.

------------------------------

Code: 1D040100

Display: Same as code

Used by:

Cause: This computer vision number is not supported.

Remedy: Check the computer vision number specified in the Part data.

------------------------------

Code: 1D040110

Display: Same as code

Used by:

Cause: No value has been set for the "Lead_pitch" parameter in the Part data.

Remedy: Set a value for the "Lead_pitch" parameter.

------------------------------

Code: 1D040111

Display: Same as code

Used by:

Cause: No value has been set for the "Lead_width" parameter in the Part data.

Remedy: Set a value for the "Lead_width" parameter.

------------------------------

Code: 1D040112

Display: Same as code

Used by:

Cause: No value has been set for the "Lead_length_x" parameter (the length of leads in the X direction) in

the Part data.

Remedy: Set a value for the "Lead_length_x" parameter.

第 1278 页

------------------------------

Code: 1D040113

Display: Same as code

Used by:

Cause: No value has been set for the "Lead_length_y" parameter (the length of leads in the Y direction) in

the Part data.

Remedy: Set a value for the "Lead_length_y" parameter.

------------------------------

Code: 1D040114

Display: Same as code

Used by:

Cause: No value has been set for the "Body_size 1" parameter (the body length in the X direction) in the

Part data.

Remedy: Set a value for the "Body_size 1" parameter.

------------------------------

Code: 1D040115

Display: Same as code

Used by:

Cause: No value has been set for the "Body_size 0" parameter (the body length in the X direction) in the

Part data.

Remedy: Set a value for the "Body_size 0" parameter.

------------------------------

Code: 1D040120

Display: Same as code

Used by:

Cause: No value has been set for the "Qty 0" parameter (the quantity of leads on the left side) in the Part

data.

Remedy: Set a value for the "Qty 0" parameter.

------------------------------

Code: 1D040121

Display: Same as code

Used by:

Cause: No value has been set for the "Qty 1" parameter (the quantity of leads on the lower side) in the

Part data.

Remedy: Set a value for the "Qty 1" parameter.

------------------------------

Code: 1D040122

Display: Same as code

Used by:

Cause: No value has been set for the "Qty 2" parameter (the quantity of leads on the right side) in the

Part data.

Remedy: Set a value for the "Qty 2" parameter.

------------------------------

Code: 1D040123

Display: Same as code

Used by:

Cause: No value has been set for the "Qty 3" parameter (the quantity of leads on the upper side) in the

Part data.

Remedy: Set a value for the "Qty 3" parameter.

------------------------------

Code: 1D0402??

第 1279 页