FUJI错误代码查询.pdf - 第78页

·第10个sequence：电路板尺寸Y。 ------------------------------ Code: 1101C402 Display: 印刷顺序的印刷位置指定错误 Used by: NXTP Cause: Flexa上印刷顺序的设定值超过公差值。 Remedy: ·请指定起点和终点。 ·一侧最大可以指定10个顺序。 ·请设定次顺序的值大于前顺序的值。 ·位置的最小值和最大值在范围外(虽然印刷范围受其他参数的影响为可变数…

100%1 / 5282
Group 3: Printing sequence
Group 4: Snap-off, cleaning, inspection sequence
------------------------------
Code: 1101C1??
Display:
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: Same as code (1101C100 + i/20) where i is the sequence number.
Remedy: The sequence references a device number 0 or less or greater than 140.
The device number that has been specified in sequence data is out of range
------------------------------
Code: 1101C2??
Display:
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: Same as code (1101C200 + i/20) where i is the sequence number.
Remedy: The placing sequence's X data is out of the machine's range of movement.
There is a sequence where the X coordinate is outside the limits of the board in the X direction (PCB_X)
(single board production program).
------------------------------
Code: 1101C3??
Display:
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: Same as code (1101C300 + i/20) where i is the sequence number.
Remedy: The placing sequence's Y data is out of the machine's range of movement.
------------------------------
Code: 1101C400
Display: 1101C400
Used by: GSP5,GP2,GP3,GP551,GP6
Cause: There is an illegal combination of sequences in the production program.
Remedy: A production program must include two board fiducial sequences, two mask fiducial sequences
and two printing sequences. Check the production program sequences. As an exception it is possible to
transmit a program which contains only printing sequences.
------------------------------
Code: 1101C401
Display: 错误编码的编号无变动
Used by: GSP5,GP551,GP6,GPX
Cause: 生产程序中指定的印刷sequence超出规定范围。
Remedy: 请检查生产程序中的印刷sequence以及Proper的139.Max Limit Position S Holder, 140.Min Limit
Position S Holder。
印刷可设置范围：
(GPX V5.40以上)
·第1个sequence:－15.00mm～电路板尺寸Y
当第1个sequence的起点在电路板外围时
请将第二个sequence的起点设置为0.00mm；剩余印刷区域请从第3个sequence开始依次进行设置。
如果第1个sequence的印刷范围是0.01mm～电路板尺寸Y，
则请将之后的sequence都设置为上一个sequence的终点～电路板尺寸Y。
·最后一个sequence:电路板尺寸Y～电路板尺寸Y＋15.00mm
最后一个sequence需要印刷电路板外围时
最后第2个sequence的数值与电路板尺寸Y必须保持一致。
(GPX V5.30以前)
·第1个sequence:1mm～电路板尺寸Y
·第2～第9个sequence:上一个sequence的终点～电路板尺寸Y
第 77 页
·第10个sequence：电路板尺寸Y。
------------------------------
Code: 1101C402
Display: 印刷顺序的印刷位置指定错误
Used by: NXTP
Cause: Flexa上印刷顺序的设定值超过公差值。
Remedy: ·请指定起点和终点。
·一侧最大可以指定10个顺序。
·请设定次顺序的值大于前顺序的值。
·位置的最小值和最大值在范围外(虽然印刷范围受其他参数的影响为可变数值，但是0～电路板尺寸为止为可印刷范围)
------------------------------
Code: 1101C403
Display: 印刷顺序的印刷位置指定错误
Used by: NXTP
Cause: Flexa上的印刷顺序的两侧印刷的指定方法超出公差值。
Remedy: ·请在Front侧和Rear侧上设定相同数量的印刷位置。
·请在Front侧和Rear侧上设定相同位置的印刷位置。
------------------------------
Code: 1101C404
Display: 印刷sequence的印刷范围延伸设置错误
Used by: GPX
Cause: 印刷sequence的印刷范围延伸设置不正确。
Remedy: 请确认生产程序中的印刷sequence。
如果第1个sequence的起点在电路板外围，
则请将第二个sequence的起点设置为0.00mm。
如果最后一个sequence需要印刷电路板外围，
则最后第2个sequence的数值与电路板尺寸Y必须保持一致。
------------------------------
Code: 1101C405
Display: 印刷sequence的数量设置错误
Used by: GPX
Cause: 印刷sequence的数量未设置或超出规定范围。
Remedy: 单侧最多可设置10个sequence。如果按印刷方向进行设置，则Front和Rear的数量和位置都必须相同。
------------------------------
Code: 1101C406
Display: 印刷sequence的数量设置错误
Used by: GPX-C
Cause: 在Flexa中设置的印刷sequence(Print Solder)有误。
Remedy: (Fig.1)如果印刷sequence不设置任何数值，则可以以默认值进行印刷。(Fig.2)如果设置印刷sequence，则
请设置2个点(起点和终点)。(Fig.3)如果按印刷方向设置印刷sequence，则请设置4个点(起点和终点×2)在这种情形下
，请将起点和终点位置设置为相同数值。(Fig.4)设置时数值可以超出电路板尺寸。(以电路板尺寸Y=150mm为例)
<img src="$LKEY_ERRIMG_MC$/1101C406.jpg">
------------------------------
Code: 1101C407
Display: 「印刷sequence」项目中的印刷位置设置错误
Used by: GPX
Cause: 代表位置的最小值、最大值超出规定范围。
Remedy: 代表印刷允许范围的数值会受其它参数的影响而变动。
------------------------------
Code: 1101C408
Display: 「印刷sequence」项目中的印刷位置设置错误
第 78 页
Used by: GPX-C
Cause: 印刷位置的设置允许范围会受其它参数（丝网尺寸、锡膏卷直径）的影响而变动。如果其他参数值太大，则
印刷范围就无法合理设置。
Remedy: 请调小Mesh Size或Roll Width。
------------------------------
Code: 1101C50?
Display: 1101C50?
Used by: GSP5,GP2,GP3,GP551,GP6
Cause: ? represents a Z sequence number, where the first Z sequence is "1". The specified X (Z) value
exceeds the range.
Remedy: The input range for X (Z) is from -1 to -500 (-0.01mm to -5.00mm). Correct and then retransmit
the data.
------------------------------
Code: 1101C51?
Display: 1101C51?
Used by: GSP5,GP2,GP3,GP551,GP6
Cause: ? represents a Z sequence number, where the first Z sequence is "1". The specified Y (SPEED)
value exceeds the range.
Remedy: The input range for Y (SPEED) is from 0 to 8,000 (0.00mm/sec to 80.00mm/sec). Correct and
then retransmit the data.
------------------------------
Code: 1101C52?
Display: 1101C52?
Used by: GSP5,GP2,GP3,GP551,GP6
Cause: ? represents a Z sequence number, where the first Z sequence is "1". The X (Z) value is logically
wrong.
Remedy: Ensure that data values become smaller in sequential order.
------------------------------
Code: 1101C53?
Display: Same as code
Used by: GP551,GP6
Cause: The movement range for a cleaning sequence has been exceeded. The value replacing the "?" in
the code is the number of the problematic cleaning sequence, when the number of the first
cleaningsequence is 1.
Remedy: Check the Proper data and production program data values. The cleaning sequence range for a
double-side cleaner is found by subtracting "org_pos_clnr" (the cleaner's program origin) from both
"max_limit_pos_s_clnr" and "min_limit_pos_s_clnr", and converting the results to units of 1/100 mm. The
cleaning sequence range for a single-side cleaner is found by subtracting "org_pos_clnr" (thecleaner's
program origin) from both "max_limit_pos_y_clnr" and "min_limit_pos_y_clnr", and converting the res lts to
units of 1/100 mm.
------------------------------
Code: 1101C54?
Display: Same as code
Used by: GP551,GP6
Cause: The speed range for a cleaning sequence has been exceeded. The value replacing the "?" in the
code is the number of the problematic cleaning sequence, when the number of the first cleaning sequence
is 1.
Remedy: Correct the data and retransmit the program. The speed range for cleaning sequences is from 1
to 14500 [1/100 mm/second]. The -1 indicating the final cleaning sequence is not checked.
------------------------------
Code: 1101C55?
第 79 页