FUJI错误代码查询.pdf - 第2062页

Remedy: Re-execute the function. If the error recurs, reset MCS. ------------------------------ Code: 2100C248 Display: Media full Used by: Cause: The specified disk has no space left. Remedy: Delete unnecessary files, o…

100%1 / 5282
Code: 2100C240
Display: Illegal unit (drive) number.
Used by:
Cause: An illegal device was specified.
Remedy: Check the device.
------------------------------
Code: 2100C241
Display: Bad disk sector number
Used by:
Cause: A system error occurred.
Remedy: Change the disk, or format it and re-execute the function.
------------------------------
Code: 2100C242
Display: Media is write protected
Used by:
Cause: The specified device cannot be written to.
Remedy: If using a floppy disk, check the write protection tab on the disk. If not using a floppy, contact
Fuji.
------------------------------
Code: 2100C243
Display: Bad check sum
Used by:
Cause: A system error occurred.
Remedy: Check that the MCS/2 software was installed properly. Perform tests on the program module to
determine the roots of the problem. Check the file.
------------------------------
Code: 2100C244
Display: Read error
Used by:
Cause: The specified file could not be read.
Remedy: Check that the MCS software was installed properly. Perform tests on the program module to
determine the cause of the problem. Check the file.
------------------------------
Code: 2100C245
Display: Write error
Used by:
Cause: The specified file could not be written into.
Remedy: Check that the MCS software was properly installed. Perform tests on the program module to
determine the cause of the problem. Check the file.
------------------------------
Code: 2100C246
Display: Device not ready
Used by:
Cause: The specified device (floppy disk drive or printer) is not in the operating status.
Remedy: Make sure that the floppy disk drive lock lever is fully closed or that the printer is turned on and
set on-line.
------------------------------
Code: 2100C247
Display: Seek error
Used by:
Cause: A system error occurred.
第 2061 页
Remedy: Re-execute the function. If the error recurs, reset MCS.
------------------------------
Code: 2100C248
Display: Media full
Used by:
Cause: The specified disk has no space left.
Remedy: Delete unnecessary files, or if all files are needed, delete some after backing them up elsewhere.
------------------------------
Code: 2100C249
Display: Bad type (incompatible media)
Used by:
Cause: The specified media type is incompatible.
Remedy: Check the specified type.
------------------------------
Code: 2100C250
Display: Device busy
Used by:
Cause: A system error occurred.
Remedy: Re-execute the function after waiting a short while. If the error recurs, reset MCS.
------------------------------
Code: 2100C251
Display: Disk ID change
Used by:
Cause: A system error occurred.
Remedy: Re-execute the function after waiting a short while. If the error recurs, reset MCS.
------------------------------
Code: 2100C252
Display: Record is busy
Used by:
Cause: A system error occurred.
Remedy: Re-execute the function after waiting a short while. If the error recurs, reset MCS.
------------------------------
Code: 2100C253
Display: Disk ID change
Used by:
Cause: A system error occurred.
Remedy: Re-execute the function after waiting a short while. If the error recurs, reset MCS.
------------------------------
Code: 2100C254
Display: I/O Deadlock error
Used by:
Cause: A system error occurred.
Remedy: Re-execute the function after waiting a short while. If the error recurs, reset MCS.
------------------------------
Code: 2100C255
Display: Device is format protected
Used by:
Cause: The device cannot be formatted.
Remedy: Re-execute the function. If the error recurs, reset MCS. If the error still recurs, re-install the
software from OS-9.
------------------------------
第 2062 页
Code: 2100CA00
Display:
Used by:
Cause: Not presently supported.
Remedy:
------------------------------
Code: 2100CA01
Display: Illegal parameter
Used by:
Cause: There is a mistake in the start command.
Remedy: Correct the command statement. It should read: Ref_cp <program name> [-d=out device] [-r]
+wtlb
------------------------------
Code: 2100CA02
Display: Message file read error
Used by:
Cause: Either the message file does not exist, the file has been corrupted, or there is not enough
memory.
Remedy: After the present operation is complete, re-execute the procedure which caused the error.
Alternatively, re-install the system.
------------------------------
Code: 2100CA03
Display: Read pipe open error
Used by:
Cause: The read pipe for the console does not exist.
Remedy: Reboot the MCS.
------------------------------
Code: 2100CA04
Display: Write pipe open error
Used by:
Cause: The write pipe for the console does not exist.
Remedy: Reboot the MCS.
------------------------------
Code: 2100CA05
Display: CRT event link error
Used by:
Cause: The CRT event does not exist.
Remedy: Reboot the MCS.
------------------------------
Code: 2100CA06
Display: LS pipe create error
Used by:
Cause: The pipe for the same LS period cannot be created.
Remedy: Reboot the MCS.
------------------------------
Code: 2100CA07
Display: Work directory create error
Used by:
Cause: There is insufficient RAM disk capacity to create the work directory.
Remedy: After the present operation is complete, re-execute the procedure which caused the error.
Alternatively, reboot the MCS.
第 2063 页