FUJI错误代码查询.pdf - 第1881页
Cause: There was a syntax error. Remedy: Check the command and try to input it again. ------------------------------ Code: 21005301 Display: Comment must be enclosed by quotation marks (") in direct co Used by: Caus…
Cause: A file required by the Editor could not be opened.
Remedy: The necessary files in the editor could not be opened. Re-install the editor software. If the
problem persists contact Fuji.
------------------------------
Code: 21005003
Display: Message file open error
Used by:
Cause: A message file required by the Editor could not be opened.
Remedy: A file required by the editor could not be opened by the editor. Re-install the editor software. If
the problem persists contact Fuji.
------------------------------
Code: 21005101
Display: File open error.
Used by:
Cause: When the Editor was being started up, the specified file could not be opened.
Remedy: The specified file was not created by the editor, so it could not be specified. Specify a separate
file.
------------------------------
Code: 21005102
Display: file write error
Used by:
Cause: File could not be written.
Remedy: Check whether the file write protector is on.
------------------------------
Code: 21005103
Display: Invalid filename
Used by:
Cause: An invalid filename was used.
Remedy: Input a valid filename.
------------------------------
Code: 21005104
Display: Disk_drive not ready
Used by:
Cause: The disk drive has not been prepared.
Remedy: The floppy disk has not been set. Check the floppy disk.
------------------------------
Code: 21005105
Display: Reading file; can't execute command yet.
Used by:
Cause: The edit file is reading the memory.
Remedy: The command cannot be executed until the edit file finishes reading the memory.
------------------------------
Code: 21005200
Display: can't execute command
Used by:
Cause: The command just given does not exist.
Remedy: Check the input command, and re-input.
------------------------------
Code: 21005201
Display: syntax error
Used by:
第 1880 页
Cause: There was a syntax error.
Remedy: Check the command and try to input it again.
------------------------------
Code: 21005301
Display: Comment must be enclosed by quotation marks (") in direct co
Used by:
Cause: Comments entered when setting the command must be enclosed in quotation marks.
Remedy: Enclose comments in quotation marks.
------------------------------
Code: 21005302
Display: Nickname must be enclosed by quotation marks (") in direct c
Used by:
Cause: A comment not enclosed in quotation marks (") was found when the [end] command was
executed.
Remedy: Insert quotation marks before and after the comment.
------------------------------
Code: 21005303
Display: END command not selected
Used by:
Cause: The F6 [execute] key was pressed before specifying the method of ending the Editor.
Remedy: Select the end method with the cursor keys before pressing the [execute] key.
------------------------------
Code: 21005304
Display: Number of Device data lines is incorrect
Used by:
Cause: When copying in editor or using insert_line, the number of device data lines is incorrect so the
machine attempted to save the file.
Remedy: After altering the number of device data lines to the correct number, save the file.
------------------------------
Code: 21005305
Display: File already exists
Used by:
Cause: The specified file already exists.
Remedy: Either save the file by overwriting whatever is on the other file or change the filename.
------------------------------
Code: 21005306
Display: Now edit file record count over Not execute File save
Used by:
Cause: The file size is too big and cannot be saved.
Remedy: Change the file so that it is within the specified size.
------------------------------
Code: 21005308
Display: file saving error
Used by:
Cause: The temporary file already exists.
Remedy: Turn off the computer power and re-boot the computer.
------------------------------
Code: 21005309
Display: Data checker not execute. (data type error)
Used by:
Cause: An attempt was made to perform file save and data check on items not in the program, Proper
第 1881 页
and Status data.
Remedy: Except on the above mentioned data, data check cannot be performed. Save the changes and
shut down the editor.
------------------------------
Code: 21005310
Display: File already exists
Used by:
Cause: The file specified already exists.
Remedy: Choose whether or not to overwrite the file.
------------------------------
Code: 21005311
Display: Filename not specified
Used by:
Cause: The filename was not specified in the command.
Remedy: Specify the filename.
------------------------------
Code: 21005320
Display: Start_line or End_line not selected
Used by:
Cause: The line was not specified at "blk wrte."
Remedy: After entering the correct starting and finishing line, press the F6 [execute] key.
------------------------------
Code: 21005321
Display: Start_line or End_line record count over
Used by:
Cause: The specified line specified in the blk wrte command does not exist.
Remedy: After checking that the correct starting and finishing lines are specified, re-execute the function.
------------------------------
Code: 21005322
Display: Not "Block" or "Sequence" data
Used by:
Cause: The digitize command was executed for data other than block or sequence data.
Remedy: The digitize command can only be executed on the above mentioned data.
------------------------------
Code: 21005330
Display: Record Field Over
Used by:
Cause: When a read command was executed, the number of data items read exceeded the number able
to be handled by the software.
Remedy: Reduce the number of data items being read.
------------------------------
Code: 21005331
Display: Selected file is not a block data file.
Used by:
Cause: The selected file is not a block data file.
Remedy: Check the block data display contents. Check that "BLOCK" is displayed under the "TYPE"
heading in the ls directory display.
------------------------------
Code: 21005332
Display: Block read data does not match data block format.
Used by:
第 1882 页