FUJI错误代码查询.pdf - 第124页

Code: 1101E01A Display: 与编码相同 Used by: GPX,NXTP Cause: 离板距离超出范围。 Remedy: 请确认生产程序的Ｂｏａｄ＿ｄｅｔａｃｈ＿ｄｉｓｔａｎｃｅ。 从０.０到５.０[mm](GSP3) 请确认Job编制器的Detach Mask - Height。 从０.０到４.０[mm](GPX) 从０.０到５.０[mm](NXTP) -----------------------------…

100%1 / 5282
Used by: GSP5
Cause: Edge mode is out of range.
Remedy: Check Clamp_mode in the production program. A setting of 0 indicates mark reference, 1
indicates external reference and 2 indicates check mode.
------------------------------
Code: 1101E013
Display:
Used by: GSP5
Cause: When edge mode is check mode, the external reference is out of range.
Remedy: Check Edge_revise_limit in the production program. The range is from 0.01 to 1.00 mm.
------------------------------
Code: 1101E014
Display:
Used by: GSP5
Cause: The elongation limit is out of range.
Remedy: Check Elongation_limit in the production program. The range is from 0.00 to 10.00%.
------------------------------
Code: 1101E015
Display: 与编码相同
Used by: GSP5,GP2,GP3,GPX,NXTP
Cause: 绝对修正值X在范围之外。
Remedy: 请确认生产程序的Ａｂｓｏｌｕｔｅ＿ｏｆｓｔ．X。范围是-１.２８～１.２７[mm]。
请确认在ＦｕｊｉＦｌｅｘａ上设定的绝对偏移量X。范围为－１．２７～１．２８ｍｍ。（ＧＰＸ,NXTP）
------------------------------
Code: 1101E016
Display: 与编码相同
Used by: GSP5,GP2,GP3,GPX,NXTP
Cause: 绝对修正值Y在范围之外。
Remedy: 请确认生产程序的Ａｂｓｏｌｕｔｅ＿ｏｆｓｔ．Y。范围是-１２８～１.２７[mm]。
请确认在ＦｕｊｉＦｌｅｘａ上设定的绝对偏移量Ｙ。范围为－１．２７～１．２８ｍｍ。（ＧＰＸ,NXTP）
------------------------------
Code: 1101E017
Display:
Used by: GSP5
Cause: The center of compensation in the X-axis is out of range.
Remedy: Check Screen_locate_orgn_x in the production program. The range is -457.00 to 457.00 mm.
------------------------------
Code: 1101E018
Display:
Used by: GSP5
Cause: The center of compensation in the Y-axis is out of range.
Remedy: Check Screen_locate_orgn_y in the production program. The range is -356.00 to 356.00 mm.
------------------------------
Code: 1101E019
Display: 与编码相同
Used by: GSP5,GPX
Cause: The snapoff speed is out of range.
Remedy: Check Board_detach_speed in the production program. The range is from 0.1 to 1.0 mm/sec.
Check the detach speed for the first sequence in Fuji Flexa. Possible detach speed range: 0.1 to 40 mm/s
请确认在ＦｕｊｉＦｌｅｘａ上设定的第１顺序的离板速度。范围为，从０．１到４０[mm/sec]。（ＧＰＸ）
------------------------------
第 123 页
Code: 1101E01A
Display: 与编码相同
Used by: GPX,NXTP
Cause: 离板距离超出范围。
Remedy: 请确认生产程序的Ｂｏａｄ＿ｄｅｔａｃｈ＿ｄｉｓｔａｎｃｅ。
从０.０到５.０[mm](GSP3)
请确认Job编制器的Detach Mask - Height。
从０.０到４.０[mm](GPX)
从０.０到５.０[mm](NXTP)
------------------------------
Code: 1101E01B
Display:
Used by: GSP5,GP2,GP3
Cause: The specified number of knead times is out of range.
Remedy: Check Knead_times in the production program. The range is from 0 to 99.
------------------------------
Code: 1101E01C
Display:
Used by: GSP5,GP2,GP3
Cause: When in edge mode the compensation motor (MX) position is out of range.
Remedy: Check Screen_mx.orgn in the production program. The range is from -1000 to 30,000 pulses.
------------------------------
Code: 1101E01D
Display:
Used by: GSP5,GP2,GP3
Cause: When in edge mode the compensation motor (MYL) position is out of range.
Remedy: Check Screen_myl.orgn in the production program. The range is from -1000 to 30,000 pulses.
------------------------------
Code: 1101E01E
Display:
Used by: GSP5,GP2,GP3
Cause: When in edge mode the compensation motor (MYR) position is out of range.
Remedy: Check Screen_myr.orgn in the production program. The range is from -1000 to 30,000 pulses.
------------------------------
Code: 1101E01F
Display: 与编码相同
Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP
Cause: 钢板读取计数在范围之外。
Remedy: 请确认生产程序的Ｍａｓｋ＿ｒｅａｄ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认
Ｍａｓｋ＿ｒｅａｄ＿ｉｎｔｅｒｖａｌ）。范围是０～６５０００[块](如果是ＧＳＰ５时，范围是０～６００００[块
])。
------------------------------
Code: 1101E020
Display: 与编码相同
Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP
Cause: 清洁计数器在范围之外。
Remedy: 请确认生产程序的Ｃｌｅａｎｉｎｇ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认
Ｃｌｅａｎｉｎｇ＿ｉｎｔｅｒｖａｌ）。范围是０～６５０００[块](如果是ＧＳＰ５时，范围是０～６００００[块
])。 请确认在ＦｕｊｉＦｌｅｘａ上设定的自动清洁计数。范围为０～９９９９［块］。（GPX,NXTP）
------------------------------
Code: 1101E021
第 124 页
Display: 与编码相同
Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP
Cause: 焊锡供应计数在范围之外。
Remedy: 请确认生产程序的Ｓｏｌｄｅｒ＿ｓｕｐｐｌｙ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认
Ｓｏｌｄｅｒ＿ｓｕｐｐｌｙ＿ｉｎｔｅｒｖａｌ）。范围是０～６５０００[块](如果是ＧＳＰ５时，范围是
０～６００００[块])。 请确认在ＦｕｊｉＦｌｅｘａ上设定的焊锡供应计数。范围是０～９９９９［块］。
（GPX,NXTP）
------------------------------
Code: 1101E022
Display:
Used by: GSP5
Cause: The solder viscosity is out of range.
Remedy: Check solder_viscsty in the production program. The range is 1 to 60 [*10 Pa.s]
------------------------------
Code: 1101E023
Display:
Used by: GSP5
Cause: The solder supply one-way count is out of range.
Remedy: Check solder_supply_times in the production program. The range is 1 to 10.
------------------------------
Code: 1101E024
Display: 与编码相同
Used by: GSP5,GP551,GP6,GPX,NXTP
Cause: 手动清洁计数器在范围之外。
Remedy: 请确认生产程序的ｍａｎｕａｌ＿ｃｌｅａｎｉｎｇ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认
ｍａｎｕａｌ＿ｃｌｅａｎｉｎｇ＿ｉｎｔｅｒｖａｌ）。 范围是０～６５０００[块]。 请确认在
ＦｕｊｉＦｌｅｘａ上设定的手动清洁计数。范围为０～９９９９［块］。（GPX,NXTP）
------------------------------
Code: 1101E025
Display: 与编码相同
Used by: GSP5,GPX,NXTP
Cause: 清洁速度超出范围。
Remedy: 请确认生产程序的ｃｌｅａｎｉｎｇ＿ｓｐｅｅｄ。
范围:从１０到２００［ｍｍ／ｓｅｃ］
请确认在FujiFlexa设定的清洁速度。
范围:从１到３００［ｍｍ／ｓｅｃ］(GPX)
范围:从１０到３００［ｍｍ／ｓｅｃ］(NXTP)
------------------------------
Code: 1101E026
Display: 与编码相同
Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP
Cause: 虽然存在不使用侧夹紧的生产（65.Side_clamp为ＯＦＦ），25.Vacuum_flag不是
ALL_ON，68.Use_vacuum也没有被指定。(GSP5)
侧夹紧OFF时，请将电路板真空ON。(GPX,NXTP)
Remedy: 请检查生产程序的65.Side_Clamp,25.Vacuum_flag,68.Use_vacuum。请确认
FujiFlexa上的侧夹紧设定和电路板真空设定。(GPX,NXTP)
------------------------------
Code: 1101E027
Display: 1101E027
Used by: QP132
Cause: The board length is not specified (FQP1).
第 125 页