FUJI错误代码查询.pdf - 第1193页

Remedy: If "??" equals 1E, 64, 78, 79, AC or FE then either the nozzle center of rotation does not conform with the image of the nozzle or the image lies outside of the scan area. Make sure the nozzle is not be…

body sized.

------------------------------

Code: 1CA??00C

Display: 1CA??00C

Used by:

Cause: If "??" equals 28 this signifies that the body has failed to be detected. If "??" equal A0 then the

body edge cannot be detected. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then invalid lead pitch value.

Remedy: If "??" equals 28 then check the dimensions of the part. If "??" equal A0 then check for errors in

the part data's "part size" setting, and in the element_data detection position. If "??" equal 64, 78, 79, 7A,

7B, 7C or F0 then the lead pitch is smaller than the lead width.Check the lead pitch and the lead width.

------------------------------

Code: 1CA??00D

Display: 1CA??00D

Used by:

Cause: If "??" equals 28 this signifies that there were no body detection points. If "??" equal A0 then

mismatch between the part size and the part data. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then there are

overlapping elements.

Remedy: If "??" equals 28 then the results of calculating the body detection points using the body data

prevented the body from being detected because the leads were concealed by the body. If "??" equal A0

then specify the correct part size in part data. When there is a large size difference from part to part,

specify a large tolerance value. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then check the element data, and

ensure none of the elements are overlapping.

------------------------------

Code: 1CA??010

Display: 1CA??010

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 78,

79, 96, 99, 9B or 9E this signifies that the positioning phase could not be determined. If "??" equal A0

then coarse positioning is not possible. If "??" equal F0, F1 or F2 then search failed.

Remedy: If "??" equals 64, 78, or 79 this indicates that there is a problem with the brightness of the

image. Make sure that there is no dirt or dust reflected in the background. If "??" equals 96,99, 9B or 9E

then verify that the part and mechanical chuck do not lie outside of the camera field of vision. Also make

sure that there is not a problem with the brightness of the image and that there are no contaminants

reflected in the background.

If "??" equal A0 then cCheck for the following:

o Part or mechanical chuck protruding from the camera's field of vision.

o Image brightness problem.

o Image problem caused by dust, etc., on the part background.

When a nozzle is being used, the size of the nozzle's reflective disk should be at least 1.7 times the part

size.

If "??" equal F0, F1 or F2 then check for errors in the part data. Create a model to reduce the size of the

circumscribed square outline for the entire model.

------------------------------

Code: 1CA??011

Display: 1CA??011

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 1E, 64,

78, 79, AC, or FE then boundary detection could not begin because the nozzle was bent. The image lies

outside the scan area. If "??" equals 7C, 82, 83, 98, 9D or B4 this indicates that the leads could not be

acquired from the body and background. If "??" equals 8C, E6, E7 or E9 there are too few leads described

in part data. If "??" equal F0, F1 or F2 then model size exceeds the tolerance range.

第 1192 页

Remedy: If "??" equals 1E, 64, 78, 79, AC or FE then either the nozzle center of rotation does not conform

with the image of the nozzle or the image lies outside of the scan area. Make sure the nozzle is not bent.

Or in the case that the image lies outside of the camera field of vision, enlarge the scan area. If "??" equals

7C, 82, 83, 98, 9D or B4 this signifies that the body could not be distinguishedor separated from the

leads. Input the Lead_brightness in part data. If "??" equals 8C, E6, E7 or E9 there are too ew leads

described in part data and the positioning phase could not be carried out. Correct the part data. If "??"

equal F0, F1 or F2 then check the model size. Create a model to reduce the size of the circumscribed

square outline for the entire model.

------------------------------

Code: 1CA??012

Display: 1CA??012

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 1E, 64,

78, 79, AC, or FE this signifies that the image of the part that has been found is smaller than thesize of

the nozzle. If "??" equals 8C, E6, E7, or E9 then the part is too big.

No license key is required when ?? = F1 or F2.

Remedy: If "??" equals 1E, 64, 78, 79, AC, or FE then either the image of the part that has been found is

smaller than the size of the nozzle or the image lies outside of the field of vision. Make sure the correct

nozzle has been specified. Or in the case that the image lies outside of the camera field of vision, enlarge

the scan area. If "??" equals 8C, E6, E7, or E9 then a valid field of vision cannot be acquired since the

part size is too big.

When ?? = F1 or F2, confirm that there is a license key, or that the license key is operating properly.

------------------------------

Code: 1CA??013

Display: 1CA??013

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 82, 83, 8D, 8E, 98, 9D or B4 this indicates that the leads could not be acquired from the body and

background. If "??" equals 8C, E6, E7, or E9 then no leads exist.

Remedy: If "??" equals 7B, 7C, 82, 83, 8D, 8E, 98, 9D or B4 this signifies that the body could not be

distinguished or separated from the leads. Input the Lead_brightness in part data. If "??" equals 8C, E6,

E7, or E9 this indicates that not a single lead was reflected. Make sure that the image has been acquired

properly.

------------------------------

Code: 1CA??014

Display: 1CA??014

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 82, 83, 98 or B4 this signifies that the threshold value request was improper. If "??" equals 8C, E6 or

E7 then the body size has not been input in part data. If "??" equal 8D or 8E then the body size is

incorrect.

Remedy: If "??" equals 7B, 7C, 82, 83, 98, or B4 this is an internal error that normally does not occur. If

"??" equals 8C, E6, E7 or E9 then input the correct data in part data. If "??" equal 8D or 8E then the

specified body size exceeds the tolerance value registered in part data. Check the body size.

------------------------------

Code: 1CA??015

Display: 1CA??015

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 7B, 7C,

98 or b4 then part search area is incorrect.

Remedy: If "??" equal 7B, 7C, 98 or b4 then check to see if a nozzle size was registered which is larger

第 1193 页

than the part size. As a rule, the size of the black plate attached to chucks is entered at that setting item.

------------------------------

Code: 1CA??016

Display: 1CA??016

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 8D or

8E then the image cannot be converted to binary data.Remedy: If "??" equal 8D or 8E then this is a highly

unusual internal error. Contact your Fuji service representative if this error occurs.

Remedy:

------------------------------

Code: 1CA??017

Display: 1CA??017

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 8D or

8E then processing is not possible because the space between bumps is too narrow.

Remedy: If "??" equal 8D or 8E then use a bump array where the distance between the bumps (leads) is

1/6 or more of the average vertical and horizontal body size.

------------------------------

Code: 1CA??021

Display:

Used by:

Cause: ?? is the PD Vision_type in hexadecimal numbers. If ?? = 64, 69, 78, 79, 7A, 7D, 7E, or 7F ,the

coarse position cannot be determined. If ?? = 7B, 7C, 80, 81, 82, 83, 87, 88, 8C, E6, E7, E9, EB, EC, 98,

or 9D, less than half the specified leads were found. If ?? = 99, part cannot be found.

Remedy: If ?? = 64, 69, 78, 79, 7A, 7D, 7E, or 7F ,check that there is no problem with image brightness,

and check that there is no problem with a dirty background. If ?? = 7B, 7C, 80, 81, 82, 83, 87, 88, 8C,

E6, E7, E9, EB, EC, 98, or 9D, check for errors in the part data. In particular, check the lead size data. If

?? = 99, the part which should be detected cannot be found. Check to see if the part appears on the

image display.

------------------------------

Code: 1CA??022

Display: 1CA??022

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 8C, E6, E7, E9, EB, EC, 98, or 9D fewer than half of the leads specified in part data could be found. If

"??" equal 8D or 8E then part position cannot be determined because fewer than 2 bumps were found.

Remedy: If ?? is 7B, 7C, 80, 81, 82, 83, 87, 8C, E6, E7, E9, EB, EC, 98, or 9D check the part data,

especially the number of leads and the lead size. If "??" equal 8D or 8E then check the part data. Also

check to see if the bump sizes are correct. Or, increase the bump size tolerance value.

------------------------------

Code: 1CA??023

Display: 1CA??023

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 88, 98, or B4 the blob area is incorrect.

Remedy: This is an internal processing error which should not normally occur. If this error occurs, notify

Fuji.

------------------------------

Code: 1CA??024

Display: 1CA??024

Used by:

第 1194 页