FUJI错误代码查询.pdf - 第2172页
"Nozzle configuration"on the "Nozzle optimization screen",check the arrangement of the nozzles on the machine. If "Use program nozzle configuration"was selected,check the nozzle arrangement …
Used by:
Cause: <XP*42>Feeder optimization/Feeder configuration was performed selecting "Configure feeders
automatically"but feeders cannot be arranged.
Remedy: <XP*42>Reduce the number of part types and feeders being used or,for the XP-242 only,change
the "Feeder types used"setting in the "Feeder optimization"screen and then press [Execute].
------------------------------
Code: 2307800F
Display: Trays cannot be arranged.
Used by:
Cause: <XP*42>Feeder optimization/Feeder configuration was performed using the "Configure feeders
automatically"setting but trays cannot be arranged.
Remedy: <XP*42>Reduce the number of part types or trays being used.
------------------------------
Code: 23078011
Display: Optimization was performed using the [Fix feeder configuration]setting but trays could not be
arranged.
Used by:
Cause: <XP*42>Feeder optimization/Feeder configuration was performed using the "Fix feeder
configuration (Do not change feeder positions)"setting but trays could not be arranged.
Remedy: <XP*42>Check the feeder set up on the machine or optimize by selecting "Configure Feeders
Automatically"under "Feeder Configuration"in the "Feeder Optimization"screen.
------------------------------
Code: 23078018
Display: Tray size is too large to be loaded.
Used by:
Cause: <XP*42>The Tray Length or Width value in the Part Type data exceeds the maximum.(Tray
Length maximum:330mm;Tray Width maximum:276mm)
Remedy: <XP*42>Confirm that the Tray Length and Width values in the Part Type data do not exceed
330mm and 276mm.Trays larger than this cannot be loaded.
------------------------------
Code: 2307803B
Display: Stage number is not defined.
Used by:
Cause: <XP*42>Stage number is not defined.
Remedy: <XP*42>Input the Stage number.
------------------------------
Code: 23078042
Display: The necessary nozzles could not be allocated.
Used by:
Cause: <XP*42>Nozzle optimization/Nozzle configuration was optimized using the "Configure nozzles
automatically"setting but the necessary nozzles could not be allocated.
Remedy: <XP*42>Check the Nozzle Name,Minimum Nozzle Diameter and Maximum Nozzle Diameter
values in the Part Type data or reduce the number of parts types and feeders being used.
------------------------------
Code: 23078044
Display: No matching nozzle.
Used by:
Cause: <XP*42>The nozzle selected under Nozzle Name in the Part Type data is not on the machine.If a
Nozzle Name has not been set,there is no nozzle available to handle the range between the Minimum and
Maximum Nozzle Diameter values set.
Remedy: <XP*42>If optimization was performed with "Use machine nozzle configuration"selected under
第 2171 页
"Nozzle configuration"on the "Nozzle optimization screen",check the arrangement of the nozzles on the
machine.
If "Use program nozzle configuration"was selected,check the nozzle arrangement in the program.
If this does not resolve the problem,optimize using the "Configure nozzles automatically"setting.
------------------------------
Code: 23078824
Display: A required nozzle does not exist in the nozzle list on the machine.
Used by:
Cause: <XP*42>The nozzle selected under Nozzle Name in the Part Type data is not listed on the
machine.If a Nozzle Name has not been set,no listed nozzle can handle the range between the Minimum
and Maximum Nozzle Diameter values set.
Remedy: <XP*42>Check the Nozzle Name,Minimum Nozzle Diameter and Maximum Nozzle Diameter in
the Part Type data.
------------------------------
Code: 23078827
Display: A slot that has not been allocated a part number is set as an Alt.Feeder.
Used by:
Cause: <XP*42>A vacant slot number (no setting data)is set as the Alt.Feeder.
Remedy: <XP*42>Specify a slot number with a same part number.
------------------------------
Code: 2307903C
Display: Slot number is not defined.
Used by:
Cause: <XP*42>Slot number is not defined.
Remedy: <XP*42>Input the Slot number.
------------------------------
Code: 2307904A
Display: The Alt.Feeder function is not looping.
Used by:
Cause: <XP*42>An Alt.Feeder setting which includes two different stages is not suitable for the loop type
setting.
Remedy: <XP*42>Change the setting so that the Alt.Feeder setting has the same stage-slot number.
------------------------------
Code: 2307904B
Display: The Alt.Feeder is outside the permitted range.
Used by:
Cause: <XP*42>The Alt.Feeder input is outside the permitted range.The designated slot number does not
exist.
Remedy: <XP*42>Enter an Alt.Feeder within the permitted range.
------------------------------
Code: 23079828
Display: The Alt丏Feeder must be set to a separate feeder.
Used by:
Cause: <XP*42>The Slot Number and Alt丏Feeder are identical.
Remedy: <XP*42>Specify a Alt丏Feeder which is different from the slot number.
------------------------------
Code: 2307A10C
Display: Unregistered Packaging Type.A feeder cannot be selected.
Used by:
Cause: <XP*42>Cannot optimize because feeder width is unknown.A registered Packaging Type must be
used so that a feeder can be selected.
第 2172 页
Remedy: <XP142>Set Packaging to 1:Bulk,2:32mm Adhesive,3:12mm (no U-groove)Embossed,16or24mm
Embossed,5:8mm Paper or Embossed,12mm (U-groove)Embossed,or 7:32mm Embossed.
<XP242>Set Packaging to 0:Tray,2:32mm Adhesive,3:12mm (no U-groove)Embossed,16or24mm
Embossed,4:Stick Feeder,5:8mm Paper or Embossed,12mm (U-groove)Embossed,7:32mm and Over
Embossed or 9:Stick (U-groove)Feeder.
------------------------------
Code: 2307E000
Display: PlaceBefore is set to loop.
Used by:
Cause: Cannot optimize because PlaceBefore is set to loop.
Remedy: Do not set PlaceBefore to loop in the sequence data.
------------------------------
Code: 2307E001
Display: The stage-slot number does not match the packaging type in part data.
Used by:
Cause: A part number with a Packaging Type of "Tray"is set for a Feeder stage-slot number or a part
number with a Packaging Type other than "Tray"is set for a Tray stage-slot number.
Remedy: For Feeder stage-slot numbers,specify a part number with a Packaging Type other than
"Tray".For Tray stage-slot numbers,specify a part number with Packaging Type of "Tray".Another option is
to optimize selecting "Configure feeders automatically"under "Feeder configuration"in the "Feeder
optimization"screen.
------------------------------
Code: 2307E002
Display: The part number does not match that of the Alt丏Feeder.
Used by:
Cause: The slot designated as Alt丏Feeder has a part number different from the one currently being
used.
Remedy: Select an Alt丏Feeder that has a part number that is the same as the one currently being used.
------------------------------
Code: 2307E003
Display: An unavailable stage is set in the feeder setup data.
Used by:
Cause: Stage 2 is set in the feeder setup data for the single side parts supplying machine.
Remedy: Either delete the stage 2 feeder data,or move them to stage 1.
------------------------------
Code: 2307E004
Display: The part size or Scan Area X,Scan Area Y setting exceeds the scanning range that can be handled
by the camera.
Used by:
Cause: The part size or Scan Area X,Scan Area Y setting exceeds the scanning range that can be handled
by the camera.
Remedy: Specify a part size or Scan Area X,Scan Area Y setting value that is within the scanning range
that can be handled by the camera.
With the Pick-up Point Offset X and Pick-up Point Offset Y settings taken into account,the maximum
part size that may be specified is 20 mm 事20 mm,and the maximum scan area is 25 mm 事24 mm,
------------------------------
Code: 2307E005
Display: A nozzle that matches nozzle number **cannot be found.
Used by:
Cause: A nozzle that matches nozzle number **cannot be found.
Remedy: If optimization was performed using the "Use machine nozzle configuration"setting under "Nozzle
第 2173 页