FUJI错误代码查询.pdf - 第274页

(2) 没有解决时，请重新接通电源。 (3) 上述的对策也不能解决时，对不起麻烦您获取错误发生时的跟踪数据，记录下Flexa的设定，与弊公司Support联系 。 ------------------------------ Code: 11C00??? Display: 11C00??? Used by: QP242,QP201,QP202,QP203,QP132 Cause: A device number specified in…

100%1 / 5282
(2) 上述的对策也不能解决时，对不起麻烦您获取错误发生时的跟踪数据，记录下Flexa的设定，与弊公司Support联系
。
------------------------------
Code: 11300063
Display: 机器连接总数的电信文件尺寸超出
Used by: NXTP
Cause: [ CMM ] 生产线传输时，由于'机器连接总数'的电信文件尺寸超出了设定范围，因此中断了处理。
Remedy: (1) 请重新接通电源。
(2) 上述的对策也不能解决时，对不起麻烦您获取错误发生时的跟踪数据，记录下Flexa的设定，与弊公司Support联系
。
------------------------------
Code: 11300064
Display: 往复搬运轨道的电路板搬运模式不正确
Used by: NXTP
Cause: [ CMM ] 生产线传输时，由于在机器的规格中被指定了无往复搬运轨道的电路板搬运模式（Shuttle
conveyor mode），因此中断了处理。
Remedy: (1) 请参考以下，设定机器编辑画面的传输路线信息的项目「Shuttle conveyor mode」。
　　第1台Flexa优先时　　交叉(Cross)
　　第2台Flexa优先时　　平行(Straight)、交叉(Cross)、集合（Converging）
　　第1台Machine优先时　交叉(Cross)
　　第2台Machine优先时　请对照机器的设定，设定Flexa。
(2) 没有解决时，请重新接通电源。
(3) 上述的对策也不能解决时，对不起麻烦您获取错误发生时的跟踪数据，记录下Flexa的设定，与弊公司Support联系
。
------------------------------
Code: 11300065
Display: 机器联结号码不正确
Used by: NXTP
Cause: [ CMM ] 生产线传送时，因为机器联结号码(Connection number)与机上的机器号码(Line Configuration
Order)不同而中断了处理。
Remedy: (1) 请将机器编辑画面的传输线信息的项目「Connection number」设定到下记的参考中 。
　　请设定第1台机器时为「1」、第2台机器时为「2」。
(2) 运用2联结时，请进行以下的设定。
　　·请在「Double」中设定「Conveyor Type」。
　　·请在运用2联结的机器的「Connection name」中设定同样的名字。
(3) 不解决时，请重新接通电源。
(4) 采用上述对策不能解决时，麻烦您取得错误发生时的跟踪数据，记录Flexa的设定，与本公司电话服务中心联络。
------------------------------
Code: 11300066
Display: 机器连接台数不正确
Used by: NXTP
Cause: [ CMM ] 生产线传输时，由于被指定了大于2台的机器连接台数，因此中断了处理。
Remedy: (1) 请重新接通电源。
(2) 上述的对策也不能解决时，对不起麻烦您获取错误发生时的跟踪数据，记录下Flexa的设定，与弊公司Support联系
。
------------------------------
Code: 11300067
Display: 生产线传输通知时间异常
Used by: NXTP
Cause: [ CMM ] 自动生产中想要进行生产线传输。由于有可能影响生产，因此中断了处理。
Remedy: (1) 请停止通道1、通道2的自动生产，再次进行生产线传输。
第 273 页
(2) 没有解决时，请重新接通电源。
(3) 上述的对策也不能解决时，对不起麻烦您获取错误发生时的跟踪数据，记录下Flexa的设定，与弊公司Support联系
。
------------------------------
Code: 11C00???
Display: 11C00???
Used by: QP242,QP201,QP202,QP203,QP132
Cause: A device number specified in the placing sequence data is incorrect (out of range).
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
For sequences above 4096, 4096 is displayed.
Remedy: Specify the correct data for D in the production program's N_data.
------------------------------
Code: 11C01???
Display: 11C01???
Used by:
Cause: An attempt was made to use device numbers 1 - 3 (85 - 87) even though the MTU1 (MTU2) was
specified.
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Specify correct data for D in the production program's N_data for sequences other than 1 -3 and
85 - 87.
------------------------------
Code: 11C02???
Display: 11C02???
Used by:
Cause: There is a mistake in the TPU's original device setting for a particular device.
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Specify correct data for OD in the production program's D_data.
------------------------------
Code: 11C03???
Display: 11C03???
Used by:
Cause: There is a mistake in the TPU's unit number setting for a particular device.
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Specify correct data for TU in the production program's D_data.
------------------------------
Code: 11C04???
Display: 11C04???
Used by:
Cause: There is a mistake in the TPU's magazine number setting for a particular device.
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Specify correct data for TM in the production program's D_data.
------------------------------
Code: 11C05???
Display: 11C05???
Used by:
Cause: This combination of TPU unit number and magazine number has already been specified for
第 274 页
another device.
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Check and correct the data item combination D_data TU and D_data TM in the production
program.
------------------------------
Code: 11C06???
Display: 11C06???
Used by: QP132
Cause: There is an unspecified next device in the next device loop.
??? indicates the sequence number (in hexadecimal).
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Check the next device loop of the appropriate sequence in the production program. Specify the
next device in Next.
------------------------------
Code: 11C07???
Display: 11C07???
Used by: QP132
Cause: The next device station number is different from the first device.
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Specify correct data for Next in the production program's D_data.
------------------------------
Code: 11C08???
Display: 11C08???
Used by: QP132
Cause: The loop does not close even though the next device nest has exceeded 30 (12 for the QP132).
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Check the next device loop of the appropriate sequence. Change Next in D_data so that the loop
closes within 30 devices (within 12 for the QP132).
------------------------------
Code: 11C0A???
Display: Same as Code.
Used by: QP132
Cause: The device comment of the device used by the specified sequence, is not set. This setting must be
made for the QP132.
("???" represents the sequence number in hexadecimal format. However, if the sequence number is 4096
or greater, subtract 4096.)
Remedy: Set the device comment.
------------------------------
Code: 11C10???
Display: 11C10???
Used by: QP242,QP201,QP202,QP203,QP132
Cause: An x coordinate in sequence data is out of range in the minus direction (for example placing area
or movement range).
(??? indicates the sequence number (in hexadecimal).)
(For sequences above 4096, 4096 is displayed.)
Remedy: Specify correct data for X in the production program's N_data.
------------------------------
第 275 页