FUJI错误代码查询.pdf - 第1295页
Cause: A level area was not found in the Y direction. Remedy: Check the part shape. Check the pickup conditions. Check the Part data Y axis length. ------------------------------ Code: 1D050004 Display: Used by: Cause: A…
Cause: An edge could not be detected on the right side of the part.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D04C7??
Display:
Used by:
Cause: An edge could not be detected on the upper side of the part.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D04D000
Display:
Used by:
Cause: The part pickup slippage was too large (X direction).
Remedy: Check how the parts are being supplied.
------------------------------
Code: 1D04D080
Display:
Used by:
Cause: The part pickup slippage was too large (Y direction).
Remedy: Check how the parts are being supplied.
------------------------------
Code: 1D04D100
Display: Same as code
Used by:
Cause: Component inclination is excessive.
Remedy: Check the manner in which components are supplied.
------------------------------
Code: 1D04E???
Display:
Used by:
Cause: The image in vision processing is not correct so operation was canceled.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D04F???
Display:
Used by:
Cause: There was a logical error in the management program.
Remedy: Check Part data.
------------------------------
Code: 1D050002
Display:
Used by:
Cause: Parts are not being picked.
Remedy: Replenish the part supply.
------------------------------
Code: 1D050003
Display:
Used by:
第 1294 页
Cause: A level area was not found in the Y direction.
Remedy: Check the part shape. Check the pickup conditions. Check the Part data Y axis length.
------------------------------
Code: 1D050004
Display:
Used by:
Cause: A Y length cannot be determined.
Remedy: Check the part shape. Check the pickup conditions. Check the Part data Y axis length.
------------------------------
Code: 1D050005
Display:
Used by:
Cause: The Y length of the part exceeds the permitted range.
Remedy: Check the size of the part.
------------------------------
Code: 1D050006
Display:
Used by:
Cause: An X length cannot be determined.
Remedy: Check the Part data X axis length. Check the part shape.
------------------------------
Code: 1D050007
Display:
Used by:
Cause: An X length cannot be determined.
Remedy: Check the Part data X axis length. Check the part shape.
------------------------------
Code: 1D050008
Display:
Used by:
Cause: The X length of the part exceeds the permitted range.
Remedy: Check the size of the part.
------------------------------
Code: 1D050009
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not
stuck to the parts.
------------------------------
Code: 1D05000A
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not
stuck to the parts.
------------------------------
Code: 1D05000B
Display:
第 1295 页
Used by:
Cause: The Y length of the part exceeds the permitted range.
Remedy: Check the size of the part.
------------------------------
Code: 1D05000C
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not
stuck to the parts.
------------------------------
Code: 1D05000D
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not
stuck to the parts.
------------------------------
Code: 1D05000E
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not
stuck to the parts.
------------------------------
Code: 1D05000F
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not
stuck to the parts.
------------------------------
Code: 1D050010
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Make sure foreign matter is not
stuck to the parts.
------------------------------
Code: 1D058002
Display:
Used by:
Cause: The part was not picked. The nozzle used with this part is too large. Vision processing could not
detect any part.
Remedy: Re-supply parts. If parts were picked and this error occurred, make the nozzle smaller. Lower
the CCD level so that parts can be detected.
第 1296 页