FUJI错误代码查询.pdf - 第1183页

accuracy of the device description, or reduce the pickup uncertainty so that blob analysis is no longer required. ------------------------------ Code: 1C410134 Display: Used by: Cause: There is insufficient data in the g…

Remedy: Make the device description tolerance settings (pickup tolerance x, pickup tolerance y, rotation

tolerance) smaller. Generally, if the parts are small, the edge of the nozzle protrudes, and this makes the

vacuum weaker, and the parts can therefore easily slide after vision processing is complete. Caution must

be exercised on this point.

------------------------------

Code: 1C410129

Display:

Used by:

Cause: Training cannot be done because the coarse edge is incorrect.

Remedy: Enter a correct device description coarse edge. Check the following:

Coarse_edge_angle

Coarse_edge_l1

Coarse_edge_d1

Coarse_edge_l2

Coarse_edge_d2

Coarse_edge_e1_polarity

Coarse_edge_e3_polarity

break_rate

max_break

------------------------------

Code: 1C410130

Display:

Used by:

Cause: The coarse edge pickup tolerance is too large.

Remedy: Make the device description tolerance settings (pickup tolerance x, pickup tolerance y, rotation

tolerance) smaller.

------------------------------

Code: 1C410131

Display:

Used by:

Cause: The coarse edge tolerance (positional uncertainty) is too large.

Remedy: Make the generic device description tolerance settings (pickup tolerance x, pickup tolerance y,

rotation tolerance) smaller.

------------------------------

Code: 1C410132

Display:

Used by:

Cause: The blob cannot be found in the nozzle position.

Remedy: If the nozzle seen at the monitor is not dirty, this is probably a hardware problem.

------------------------------

Code: 1C410133

Display:

Used by:

Cause: A blob analysis failed to determine the device rotation angle during inspection. However, device

training indicated that the angle could be determined. Therefore the run-time image is not what the

software expects based on the device description. Pickup uncertainty is large enough to require that blob

analysis be used during device inspection. In such cases, during device training, the system uses the

device description to predict whether useful angle information will appear in the blob results. If the

system expects angle information to appear and it does not, then this error occurs.

Remedy: Check that the direction is correct. Also, check the part placement direction in PD. If the nozzle

edge protrudes from the part (the nozzle is too large) this error can also occur. Either improve the

第 1182 页

accuracy of the device description, or reduce the pickup uncertainty so that blob analysis is no longer

required.

------------------------------

Code: 1C410134

Display:

Used by:

Cause: There is insufficient data in the generic device description.

Remedy: Fix the generic device description. If this error occurs often, contact Fuji.

------------------------------

Code: 1C410139

Display:

Used by:

Cause: The nozzle edge is protruding from the part.

Remedy: Make the nozzle size smaller. If this error occurs often, contact Fuji.

------------------------------

Code: 1C410142

Display:

Used by:

Cause: The vision processing program angular uncertainty calculations are contradictory.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C410143

Display:

Used by:

Cause: The caliper window does not fit properly.

Remedy: Optically reduce the image magnification, correct the pickup nozzle, or center the nozzle in the

field of view. That is, make the generic device description tolerance settings (pickup tolerance x, pickup

tolerance y, rotation tolerance) smaller.

------------------------------

Code: 1C410144

Display:

Used by:

Cause: The input nozzle size value is not the same as the actual value.

Remedy: Input the correct value in the production program and retransmit the program.

------------------------------

Code: 1C420002

Display:

Used by:

Cause: The command to the vision processing system is abnormal.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420004

Display:

Used by:

Cause: A command made to vision processing is incorrect.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420007

Display:

Used by:

Cause: A command made to vision processing is incorrect.

第 1183 页

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420009

Display:

Used by:

Cause: A command made to vision processing is incorrect.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420010

Display:

Used by:

Cause: A command made to vision processing is incorrect.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420011

Display: 1C420011

Used by:

Cause: Even though the generic device descriptions were not transmitted correctly, production is carried

out. This error occurs when the machine finds Part data with the same name but a different date.

Remedy: Modify the Part data and then completely erase the production program, and retransmit it to the

machine. If this error occurs due to a fiducial mark, after initializing the system measure the Proper data

and then switch off and re-start the machine.

------------------------------

Code: 1C420012

Display:

Used by:

Cause: A command made to vision processing is incorrect.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420013

Display:

Used by:

Cause: A mark or part cannot be detected. If a mark is not detected, the mark size is incorrect, the mark

is dirty or the bright setting is incorrect.

Remedy: This generally occurs due to parts being mis-picked. Check that the mark size is correct and

that the mark is clean. Check and adjust the brightness setting by pressing the [VISION], [BRIGHT] and

[MARK] command keys. Generally, if the mark can be seen clearly at the monitor, adjustment is not

necessary.

------------------------------

Code: 1C420014

Display:

Used by:

Cause: Vision processing system communication error.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420015

Display:

Used by:

Cause: An error occurred during file forwarding.

Remedy: Part of the system program or the data has been corrupted. Contact Fuji.

------------------------------

第 1184 页