FUJI错误代码查询.pdf - 第600页

Display: ST1:Nozzle up/down error ST1:UP-lmt sensor ON Used by: CP643 Cause: The ST1 cylinder upper limit sensor is ON even though the machine has lowered the nozzle at ST1 to pick up a part. Remedy: Check the ST1 cylind…

Used by: CP5,CP6M,CP65,CP652C,CP642,CP643

Cause: The quantity of cooling oil is not sufficient. There is a fault in the circulating motor. There is a

fault in the detecting sensor.

Remedy: Switch off the machine power and check if the oil quantity is within specifications. Check the

circulating motor and the detecting sensor.

------------------------------

Code: 12061012

Display: Nzl origin search err stn12.(cp6)

Used by:

Cause: The nozzle origin position cannot be found.

Remedy: If this error occurs often and at random (ie: not always in the same nozzle), check the

adjustment of the origin position sensor. If this error occurs in a specific nozzle, check the clutch section

of this nozzle.

------------------------------

Code: 12061013

Display: Pallet ID Zero Error

Used by: CP652C

Cause: The result of reading the pallet ID of the pallet on the up-elevator was a pallet ID of "0".

Remedy: Use the pallet ID write command to set a proper ID_No. A value from 1 to 255 can be used as a

valid ID_No. Refer to the Operation Manual for information regarding the ID_No write command.

------------------------------

Code: 12061014

Display: "Ref. side clamp mesh error" (CP-642)

Used by: CP642,CP643

Cause: The guiderail on the XY table did not mesh with the guide on the conveyor.

Remedy: Align the XY table guiderail with the guide on the conveyor.

------------------------------

Code: 12061015

Display: "Interfered with backup pin"

Used by: CP642,CP643

Cause: The XY table structure interfered with the backup pin.

Remedy: Change the position of the backup pin.

------------------------------

Code: 12061016

Display: "ST15 nozzle origin error.", "Return nzl hldr to org pos." (CP6/6M)

Used by: CP6,CP6M,CP65,CP642,CP643

Cause: A Station 15 nozzle origin position check failed to confirm the origin.

Remedy: Return the nozzle holder to a position near the origin. (Nozzle disorientation may occur after

continuous production involving 90[deg] rotation.) If this error occurs even though the nozzleholder is at

the origin position, the Station 15 origin position check sensor requires adjustment.

------------------------------

Code: 12061017

Display: ST1:Nozzle up/down error

ST1:UP-lmt sensor OFF

Used by: CP643

Cause: The ST1 cylinder upper limit sensor was OFF even though the stopper has been engaged to

prevent the nozzle at ST1 from descending,after the head at ST20 was a skipped head during D-axis

positioning or D-axis retraction at the start of automatic operation.

Remedy: Check the ST1 stopper and the ST1 cylinder upper limit sensor(X06A)

------------------------------

Code: 12061018

第 599 页

Display: ST1:Nozzle up/down error

ST1:UP-lmt sensor ON

Used by: CP643

Cause: The ST1 cylinder upper limit sensor is ON even though the machine has lowered the nozzle at

ST1 to pick up a part.

Remedy: Check the ST1 cylinder upper limit sensor(X06A)

------------------------------

Code: 12061019

Display: ST11:Nozzle up/down error

ST11:UP-lmt sensor OFF

Used by: CP643

Cause: The ST11 cylinder upper limit sensor was OFF even though the stopper has been engaged to

prevent the nozzle at ST11 from descending,after the head at ST10 was a skipped head during at the start

of automatic operation.

Remedy: Check the ST11 stopper and the ST11 cylinder upper limit sensor(X06B)

------------------------------

Code: 1206101A

Display: ST11:Nozzle up/down error

ST11:UP/DWN sensor error

Used by: CP643

Cause: Both the cylinder upper limit and lower limit sensors are ON even though the machine has

lowered the nozzle ae ST11 to place a part.

Remedy: Check the ST11 cylinder upper limit sensor(X06B)

------------------------------

Code: 1206101B

Display: Production method does not match

Check Proper and header data

Used by: CP643

Cause: The production program item "Multiple pcb set" is set to "2", even though the Proper data item

"mc_pcb_type" is set to "1". These data do not match.

Remedy: Use one of the following remedies.

1. Set Proper item "mc_pcb_type" to "0".

2. Set the production program item "Multiple pcb set" to "1" and ensure there is only one board's worth of

sequences in the sequence data.

------------------------------

Code: 1206101C

Display: Nozzle holder origin position error.

Used by: CP-742ME, CP-742E, CP-752E

Cause: The nozzle holder is not at its origin position.

Remedy: Frequent occurrences of this error at the same shaft indicates a shaft rotation problem.

------------------------------

Code: 1206101D

Display: Parts height sensor malfunction.

Used by: CP-742ME, CP-742E, CP-752E

Cause: Parts height sensor is soiled.

Remedy: Wipe the sensor beam emitter and receptor lenses with a soft object such as a cotton swab, etc.

------------------------------

Code: 1206101E

Display: Parts height sensor error.

Used by: CP-742ME, CP-742E, CP-752E

Cause: Parts height sensor processing was not completed in the prescribed period of time.

第 600 页

Remedy: If this error occurs frequently, there may be a parts height sensor failure.

------------------------------

Code: 1206101F

Display: Feeder feed retract limit error.

Used by: CP-742ME, CP-742E, CP-752E

Cause: Feeder feed retract limit error.

Remedy: Check to see if the feeder feed lever is at the retract limit position. If not, perform an I/O check

to retract the feed lever. If the retract limit sensor fails to switch on even though the feed lever is

retracted, adjust the sensor and dog positions. If the error persists even after the adjustments, there may

be a sensor wiring problem or a sensor failure.

------------------------------

Code: 12061020

Display: The X-axis target position exceeds the plus-limit of the travel range specified in Proper data.