FUJI错误代码查询.pdf - 第2072页
------------------------------ Code: 2100E150 Display: Used by: Cause: The backup disk is protected so that the backing up operation cannot proceed. Remedy: Remove the write protect label from the backup disk and load th…
Display: copy command error
Used by:
Cause: An error occurred during a file copy operation.
Remedy: Re-execute the function. If the error recurs, re-boot MCS. If the error continues to recur,
contact Fuji.
------------------------------
Code: 2100E129
Display: not found
Used by:
Cause: A file in the install list or a file required to continue an operation does not exist on the system
disk.
Remedy: Contact Fuji.
------------------------------
Code: 2100E130
Display: protect disk
Used by:
Cause: Unable to install the system disk because of the copy protect function.
Remedy: The system disk is copy protected so that is not possible to install it into more than one
computer (MCS-16F, B, or C). However, after the system disk has been installed into a computer, it can
be installed again in the same computer any number of times.
------------------------------
Code: 2100E140
Display: install list transfer error
Used by:
Cause: The install list could not be backed up.
Remedy: Contact Fuji.
------------------------------
Code: 2100E142
Display: install list open error
Used by:
Cause: The install list could not be opened.
Remedy: Contact Fuji.
------------------------------
Code: 2100E147
Display: directory file open error
Used by:
Cause: The directory file could not be opened (Mode : 0020).
Remedy: Contact Fuji.
------------------------------
Code: 2100E148
Display: copy command error
Used by:
Cause: An error occurred during a file copy operation.
Remedy: Contact Fuji.
------------------------------
Code: 2100E149
Display: not found
Used by:
Cause: A file in the install list or a file required to continue an operation does not exist on the system
disk.
Remedy: Contact Fuji.
第 2071 页
------------------------------
Code: 2100E150
Display:
Used by:
Cause: The backup disk is protected so that the backing up operation cannot proceed.
Remedy: Remove the write protect label from the backup disk and load the disk in the drive again.
------------------------------
Code: 2100E200
Display: Pr_pipe open error
Used by:
Cause: The print command pipe (pr_pipe) could not be opened.
Remedy: Re-boot MCS.
------------------------------
Code: 2100E300
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly.
------------------------------
Code: 2100E301
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly.
------------------------------
Code: 2100E310
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly.
------------------------------
Code: 2100E311
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly. Contact Fuji if the problem cannot be solved.
------------------------------
Code: 2100E350
Display: parameter error
Used by:
Cause: The parameters to boot up the time-setting routine are incorrect.
Remedy: Re-execute the function.
------------------------------
Code: 2100E351
Display: not found
Used by:
Cause: The rtclock2 module does not exist.
Remedy: Re-install the software.
------------------------------
Code: 2100E400
Display: dsave command error
第 2072 页
Used by:
Cause: An error occurred during execution of Dsave (control).
Remedy: Re-execute the function.
------------------------------
Code: 2100E401
Display: dsave file open error
Used by:
Cause: The Dsave procedure file could not be opened.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100E403
Display: chdir() error
Used by:
Cause: The current directory could not be changed.
Remedy: Re-execute the function.
------------------------------
Code: 2100E404
Display: command error during **** process
Used by:
Cause: An error occurred during hard disk maintenance.
Remedy: Re-execute the function.
------------------------------
Code: 2100E406
Display: keyboard error
Used by:
Cause: An error occurred during key input.
Remedy: Re-execute the function.
------------------------------
Code: 2100E408
Display: get file size error
Used by:
Cause: The number of temporary media could not be calculated.
Remedy: Re-execute the function.
------------------------------
Code: 2100E411
Display: temporary device open error
Used by:
Cause: A temporary file could not be opened.
Remedy: Check that the floppy disk is set correctly in the drive.
------------------------------
Code: 2100E504
Display: change console path error
Used by:
Cause: The standard I/O path could not be selected to the terminal.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100E505
Display: CRT event link error
Used by:
Cause: A CRT event could not be linked.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
第 2073 页