FUJI错误代码查询.pdf - 第2327页

------------------------------ Code: 52??4029 Display: The changeover command for that changeover ID has already been completed. Used by: Cause: A changeover instruction was executed using the same changeover ID. Remedy:…

100%1 / 5282
Display: Remote command canceled.
Used by:
Cause: The remote command was canceled due to the machine status.
Remedy:
------------------------------
Code: 52??4022
Display: Machine power off.
Used by:
Cause: The machine power may be off.
Remedy:
------------------------------
Code: 52??4023
Display: Production program name too long.
Used by:
Cause: The production program name is too long. The maximum length is 23 characters.
Remedy: Change the production program name so that it is within 23 characters.
------------------------------
Code: 52??4024
Display: Start instruction canceled.
Used by:
Cause: The start command was canceled (release). At present cancel is not supported for the start
command.
Remedy:
------------------------------
Code: 52??4025
Display: The machine is already in a time up state.
Used by:
Cause: The board type report was confirmed(pcbconf)or a changeover executed(chgover)after the machine
for which the board type report was made was already in a time up state. Alternatively,the board type
report was confirmed several times for the same machine using the same changeover ID.
Remedy:
------------------------------
Code: 52??4026
Display: The machine is an active cell or a passive cell.
Used by:
Cause: A board type report was confirmed for the cell.
Remedy: Confirmation of a board type report is valid only for a unit.
------------------------------
Code: 52??4027
Display: A changeover ID different to the board type report from the unit was specified.
Used by:
Cause: An error was made when the changeover ID was entered,or the next board type report was
reported from the unit before the current board type report was confirmed.
Remedy: Check the Changeover ID.
------------------------------
Code: 52??4028
Display: A child process could not be ended when disconnection was performed.
Used by:
Cause: When disconnection was performed,a child process could not be normally ended and the child
process hung up.
Remedy:
第 2326 页
------------------------------
Code: 52??4029
Display: The changeover command for that changeover ID has already been completed.
Used by:
Cause: A changeover instruction was executed using the same changeover ID.
Remedy:
------------------------------
Code: 52??4030
Display: This changeover ID is not valid.
Used by:
Cause: The changeover instruction(chgover)was executed after the changeover complete report was
received from the machine.
Remedy:
------------------------------
Code: 52??4031
Display: The cell status has been changed.
Used by:
Cause: Processing was initialized because the cell status was changed during changeover.
Remedy: Check the machine's cell status.
------------------------------
Code: 52??4032
Display: A board type was reported in the middle of changeover.
Used by:
Cause: Processing was cancelled because the next board type was reported during changeover.
Remedy:
------------------------------
Code: 52??4033
Display: Changeover has been executed even though the board type has not been reported.
Used by:
Cause: The changeover response has been executed even though the board type has not been reported.
Remedy: Get a verification of the board type report for a second time.
------------------------------
Code: 52??4034
Display: The machine has already timed out.
Used by:
Cause: A command to enter changeover has been executed for a machine that has already timed out.
Remedy: After executing board type verification, it is necessary that the command to enter changeover is
executed within a set amount of time.
------------------------------
Code: 52??4035
Display: Board type verification has already been completed.
Used by:
Cause: Board type verification has been executed using the same changeover ID for a machine that has
already executed the board type verification.
Remedy: Check the changeover ID value.
------------------------------
Code: 52??4036
Display: The command to enter changeover has been executed multiple times.
Used by:
Cause: The command to enter changeover has been executed multiple times on the same machine using
the same changeover ID.
第 2327 页
Remedy: Check the changeover ID value.
------------------------------
Code: 52??4037
Display: The verification code value of the board type verification is incorrect.
Used by:
Cause: The verification code value of the board type verification has been specified as some value outside
the range of 0 - 4.
Remedy: Check the verification code value of the board type verification
------------------------------
Code: 52??4038
Display: The changeover ID value is incorrect.
Used by:
Cause: The changeover ID value has been specified as some value outside the range of 0 - FFFF.
Remedy: Check the changeover ID value.
------------------------------
Code: 52??4039
Display: The machine has already timed out.
Used by:
Cause: A command to execute board type verification has been executed for a machine that has already
timed out.
Remedy: After reporting the board type, it is necessary that the command to execute board type
verification is executed within a set amount of time.
------------------------------
Code: 52??4040
Display: Remote command deletion has been cancelled.
Used by:
Cause: While waiting for a response with regards to the deletion of the targeted remote command, the
completion of the command was reported from the machine prior to deletion.
Remedy:
------------------------------
Code: 52??4041
Display: Cell status has not been decided.
Used by:
Cause: Publication of a notice has been executed for a machine which has an undecided cell status.
Remedy: Perform a cell status request.
------------------------------
Code: 52??5001
Display: Undefined item.
Used by:
Cause: The reported item is undefined and has been assigned a default value. In the case of multiple
item data, the item names have been omitted from the item definition line.
Remedy: If it is necessary to set the reported item to something other than its default value, enter the
value.
------------------------------
Code: 52??5002
Display: Multiply defined item.
Used by:
Cause: The reported item is multiply defined. An item name has been multiply defined at the item
definition line in multiple item data.
Remedy: Generally this is caused by an error in the definition of one of the item names. Check the names
and values of the reported items.
第 2328 页