FUJI错误代码查询.pdf - 第2152页

Display: When using [Fix Feeders], there is no such slot available for the tray. Used by: Cause: The specified stage - slot number does not exist. Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTST…

------------------------------

Code: 2305000B

Display: For the item [Interval of Mount Height in order from lowest to highest], an illegal value was input

for [High Density Circuit Board].

Used by:

Cause: At the Optimize Condition Settings screen, under the item [Interval of Mount Height in order from

lowest to highest], a the setting entered in [Mount in 0.1mm Intervals up to ***mm (High Density Circuit

Board)] is not a numeric value.

Remedy: Enter a numeric value.

------------------------------

Code: 2305000C

Display: For the item [Interval of Mount Height in order from lowest to highest], the input value for [High

Density Circuit Board] is out of range (0 to 2.0).

Used by:

Cause: At the Optimize Condition settings screen, under the item [Interval of Mount Height in order from

lowest to highest], the setting entered in [Mount in 0.1mm Intervals up to ***mm (High Density Circuit

Board)] is out of range (0 to 2.0).

Remedy: Enter a value within the input range.

------------------------------

Code: 2305000D

Display: The Alt. Feeder does not exist. Do you want to set 0 for alternate feeder?

Used by:

Cause: A feeder is not set in the Alt. Feeder specified for the displayed stage - slot.

Remedy: The Feeder Setup information in the program file is incorrect. Check the settings.

------------------------------

Code: 2305000E

Display: There are too many feeders allocated to one stage.

Used by:

Cause: When automatic feeder arrangement was selected at the Optimize Condition settings screen, the

number of feeders allocated to the stage exceeded the maximum feeder slots.

Remedy: Firstly, try changing the [Use feeder type] settings.

If unsuccessful, perform optimization using the [Alt. Feeders are Removed] setting.

If still unsuccessful, reduce the part varieties used in the program.

------------------------------

Code: 2305000F

Display: There are too many trays allocated to one pallet.

Used by:

Cause: When automatic feeder arrangement was selected at the Optimize Condition settings screen, the

number of trays allocated to one pallet exceeded the maximum tray slots.

Remedy: Firstly, try changing the [Arrange Trays on the Pallet] setting to [Give Priority to Number of Kinds

over Speed (Allots two part kinds to one pallet)].

If unsuccessful, perform optimization using the [Alt. Feeders are Removed] setting.

If still unsuccessful, reduce the part varieties used in the program.

------------------------------

Code: 23050010

Display: A currently unused feeder has been fixed, however, no part data exists for that slot.

Used by:

Cause: There is no part data displayed in the Feeder Setup.

Remedy: The program file data is incorrect. Check the contents.

------------------------------

Code: 23050011

第 2151 页

Display: When using [Fix Feeders], there is no such slot available for the tray.

Used by:

Cause: The specified stage - slot number does not exist.

Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTSTN) and slot number

(PROGRAM/DEVICE+/GUTSLTN), or alternatively, use the [Automatic Most Suitable Feeder Arrangement]

setting for optimization.

------------------------------

Code: 23050012

Display: When using [Fix Feeders], there is no such slot available for the feeder.

Used by:

Cause: The specified stage - slot number does not exist.

Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTSTN) and slot number

(PROGRAM/DEVICE+/GUTSLTN), or alternatively, use the [Automatic Most Suitable Feeder Arrangement]

setting for optimization.

------------------------------

Code: 23050013

Display: When using [Fix Feeders], a feeder is too wide to place at an end slot was specified.

Used by:

Cause: In the program's feeder setup, a feeder too wide to place at an end slot was specified.

Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTSTN) and slot number

(PROGRAM/DEVICE+/GUTSLTN), or alternatively, use the [Automatic Most Suitable Feeder Arrangement]

setting for optimization.

------------------------------

Code: 23050015

Display: A feeder included in fixed feeder processing cannot be loaded on the stage because it is too close

to the feeder to the left.

Used by:

Cause: In the program's feeder setup, a feeder wide enough to interfere with the adjacent feeder on the

left side.

Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTSTN) and slot number

(PROGRAM/DEVICE+/GUTSLTN), or alternatively, use the [Automatic Most Suitable Feeder Arrangement]

setting for optimization.

------------------------------

Code: 23050018

Display: A feeder included in fixed feeder processing is too wide to be loaded on the stage.

Used by:

Cause: A tray included in fixed feeder processing is too wide to be loaded in the pallet.

Remedy: In the part data, check the tray length (PARTS/PACKCLS/PPCTRDX) and the tray width

(PARTS/PACKCLS/PPCTRDY) settings.

------------------------------

Code: 23050019

Display: A tray included in fixed feeder processing is too wide to be loaded side by side in the pallet.

Used by:

Cause: When the tray specified in the program file is placed alongside another tray in the pallet, the

combined tray width exceeds the pallet width.

Remedy: In the program file's feeder setup, check the stage number (PROGRAM/DEVICE+/GUTSTN) and

slot number (PROGRAM/DEVICE+/GUTSLTN), or alternatively, use the [Automatic Most Suitable Feeder

Arrangement] setting for optimization.

------------------------------

Code: 2305001A

Display: Are you finished?

第 2152 页

Used by:

Cause: The confirmation dialog displays at each time of completion.

Remedy: Select [Yes] to finish. Select [No] to continue.

------------------------------

Code: 2305001B

Display: The optimized program has not been saved yet. Will you save it?

Used by:

Cause: Attempting to open the program file, or optimization process has completed, but the optimized

program has not been saved to the file.

Remedy: Select [Yes] to display the dialog for saving the file with a new name.

When attempting to open the program file, select [No] to abandon the optimized program, and display the

dialog for selecting a new program file to be optimized.

When optimization process has completed, select [No] to exit without saving the optimized program.

------------------------------

Code: 2305001C

Display: No nozzle is registered.

Used by:

Cause: No valid nozzle match could be made between the Nozzle Config. file's NCFTYPE and the Nozzle

Spec. file乫s NSPNAME.

Remedy: There is a problem with either or both files. Normally, the Nozzle Config. and Nozzle Spec. files

in the MCS-X default directory are read automatically. Check that both files contain correct data. When

starting up the optimizer, in cases where prompted to specify a file because the default file cannot be

found, check the file contents and correct if necessary.

------------------------------

Code: 2305001D

Display: Nozzle Configuration File "Fujinzl.cfg" cannot be found. Specify a file?

Used by:

Cause: An attempt was made to read the Nozzle Config. File in the MCS-X default directory, but the file

could not be found. A file needs to be specified to continue.

Remedy: Select [Yes] to display the dialog for specifying a file. Select [Abort] to quit the optimizer.

------------------------------

Code: 2305001E

Display: The contents of Nozzle Configuration File are empty.

Used by:

Cause: The Nozzle Config. file is empty.

Remedy: There is a problem with the Nozzle Config file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

Code: 2305001F

Display: Contents are not Nozzle Configuration File.

Used by:

Cause: The field "UNIT", "NZLCONF" does not exist.

Remedy: There is a problem with the Nozzle Config file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

Code: 23050020

Display: Cannot read the file.

第 2153 页