FUJI错误代码查询.pdf - 第2330页
Used by: Cause: "UNIT", "PARTS" is entered in the production program but it is not used and not referred to in the device line. Remedy: When the number of entries for unused "UNIT", "PA…
------------------------------
Code: 52??5003
Display: Unknown item.
Used by:
Cause: The item which was entered is not known.
Remedy: This error is generally caused by the incorrect entry of an item's name. Check the name of the
reported item.
------------------------------
Code: 52??5004
Display: Additional unknown items.
Used by:
Cause: There are further unknown items but they cannot be displayed.
Remedy: There are too many unknown item names. Check the content of the file. The definition for the
machine-type name may be incorrect.
------------------------------
Code: 52??5005
Display: Values omitted from multiple item data.
Used by:
Cause: In multiple item data, the item name is defined at the item definition line but data is omitted from
the data lines.
Remedy: Check the data line settings.
------------------------------
Code: 52??5006
Display: Same line multiply defined in multiple item data.
Used by:
Cause: In multiple item data, a line with the same number has been multiply defined. When
downloading, the first of the data lines is taken as being the valid data line.
Remedy: Check the data line settings.
------------------------------
Code: 52??5010
Display: Values for size defining items are incorrect or they have been omitted.
Used by:
Cause: The entries for the items "DEV_NUM", "EL_NUM" or "TRAY_NUM" in "UNIT", "PROGRAM" -
"BLOCK", "HEADER" for SMD3 compatible machines have either been omitted or they are incorrect.
Correct values are reported together with the item names. Unnecessary items are not reported to the
applicable machine. When downloading, the program size is calculated using the registered values.
However, if values which exceed the maximum permissible are entered, they are changed to the maximum
and the program size is calculated.
Remedy: Check the entries for the relevant items in "UNIT", "PROGRAM" - "BLOCK", "HEADER-" in the
production program.
------------------------------
Code: 52??5100
Display: Meaningless unit.
Used by:
Cause: Although this entry is not correct it is ignored when the program is downloaded. This error may
occur in the following cases. A unit name other than "UNIT", "MARK" or "UNIT", "NOZZLE" is entered prior
to "UNIT", "PROGRAM". A unit name other than "UNIT", "PARTS" is entered prior to "UNIT", "PROGRAM".
Remedy: Check the entries for the production program.
------------------------------
Code: 52??5101
Display: Unused "UNIT", "PARTS".
第 2329 页
Used by:
Cause: "UNIT", "PARTS" is entered in the production program but it is not used and not referred to in the
device line.
Remedy: When the number of entries for unused "UNIT", "PARTS" is high, an error may occur when
downloading.
------------------------------
Code: 52??5110
Display: Block description is omitted.
Used by:
Cause: There is no "BLOCK" line for the block being reported. When downloading, the data for the
applicable block takes its default values.
Remedy: Check the block settings. If necessary, input the "BLOCK" line.
------------------------------
Code: 52??5111
Display: Block is multiply defined.
Used by:
Cause: The "BLOCK" line for the block being reported is multiply defined.
Remedy: Check the block settings.
------------------------------
Code: 52??5112
Display: Unknown block.
Used by:
Cause: This is an unknown block.
Remedy: Generally this is caused by an error in another block's name. Check the reported block name.
------------------------------
Code: 52??5113
Display: Unnecessary block for this machine type.
Used by:
Cause: This block is not used in the corresponding machine type and is therefore unnecessary. This
report is made if the machine type has no device lines and "BLOCK", "DEVICE+" in "UNIT", "PROGRAM" is
input. This report is made if the machine type has no sequence lines
and"BLOCK","SEQUENCE+"in"UNIT","PROGRAM"is input. This report is made if the machine type has not
GSS data lines and"BLOCK","SOLDER"or"BLOCK","SOLCO"in"UNIT","PROGRAM"is input.
Remedy:
------------------------------
Code: 52??5114
Display: Unnecessary block.
Used by:
Cause: There is a "BLOCK" in device data which is not referred to from sequence data. This report is
made if "BLOCK", "DEVICE+" is input for a production program in which there are no entries in the device
line in sequence data.
Remedy:
------------------------------
Code: 52??5120
Display: Unused GSS data element.
Used by:
Cause: This error is reported if there is an element in GSS data which is not referenced from the
sequence data and is,therefore,unnecessary.
Remedy:
------------------------------
Code: 53??0000
第 2330 页
Display: 与编码相同。
Used by: XP
Cause: 指令正常结束。或者指令正常启动（没有结束的模式的时候）。
Remedy:
------------------------------
Code: 53??0001
Display: 与编码相同。
Used by: XP
Cause: 指令的格式可能有下列错误。
·子指令名错误。
·变数的个数错误。
·在选项变数中指定了不被许可的选项。
Remedy: 请检查在指令格式中是否有错误。
------------------------------
Code: 53??0002
Display: 与编码相同。
Used by: XP
Cause: 别名错误。
Remedy: 请确认别名的指定。
------------------------------
Code: 53??0022
Display: 与编码相同。
Used by: XP
Cause: 已存在指定的文件。
Remedy: 请确认文件名的指定。如果可以改写的话，请指定改写的对象并重新执行指令。
------------------------------
Code: 53??0061
Display: 与编码相同。
Used by: XP
Cause: 从机器处传出了异常应答。异常内容由补充信息所通知。
Remedy: 请通过补充信息调查所通知的错误编码后进行数据修正或其他必要的处理。
------------------------------
Code: 53??0065
Display: 与编码相同。
Used by: XP
Cause: 所指定的程序在机器中不存在。
Remedy: 请确认文件名的指定。
------------------------------
Code: 53??0068
Display: 与编码相同。
Used by: XP
Cause: 在指定为删除的程序中、有不能删除的程序。
Remedy:
------------------------------
Code: 53??0069
Display: 与编码相同。
Used by: XP
Cause: 指定为删除的程序在机器中不存在。或者在被指定为删除的几个程序中有不存在于机器中的程序。
Remedy: 请确认文件名的指定。
------------------------------
Code: 53??0085
第 2331 页