FUJI错误代码查询.pdf - 第582页
Code: 12056051 Display: Empty tray removal interruption Used by: QP3 Cause: The empty tray removal process has been interrupted. Remedy: There is no need to remove the empty tray as it will be removed automatically upon …
当[Direction]が0、2时变更[Pick-up Point Offset X], 当[Direction]为1、4时变更[Pick-up Point Offset Y]，修正为
吸嘴与料盘定位板不相干扰的值。
------------------------------
Code: 12056038
Display: 吸嘴尺寸检查错误
由传感器进行的吸嘴尺寸检查发生了错误。
请确认吸嘴编辑的设定数据和已设置的吸嘴是否一致。
请确认吸嘴尺寸确认传感器是否有反应。
Used by: XP241,XP341,XP242
Cause: 由传感器进行的尺寸检查发生了错误。
Remedy: 请确认吸嘴编辑的设定数据和已设置的吸嘴是否一致。
请确认吸嘴尺寸确认传感器是否有反应。
------------------------------
Code: 12056039
Display: 吸嘴浮起传感器没有反应。请确认吸嘴浮起传感器是否正常地动作。
Used by: XP242
Cause: 吸嘴浮起传感器没有反应。
Remedy: 请确认吸嘴浮起传感器是否正常地动作。
------------------------------
Code: 12056040
Display: Ion level error
Used by: QP3
Cause: An abnormal electrical discharge may have occurred at the ionizer (static suppressor).
Remedy: Verify that there is no conductive material within 20 mm of the ionizer, then push [READY ON]
to clear the error status.
------------------------------
Code: 12056041
Display: Ion condition error
Used by: QP3
Cause: The ionizer (static suppressor) electrode needles are worn or dirty, preventing normal ion
emission.
Remedy: Turn off the machine, then clean or replace the ionizer electrode needles.
------------------------------
Code: 12056043
Display: 吸嘴保持真空压力确认传感器异常。
请确认传感器是否发生故障或者布线管道是否阻塞。
Used by: XP242
Cause: 吸嘴保持真空压力确认传感器异常。
Remedy: 请确认传感器是否发生故障或者布线管道是否阻塞。
------------------------------
Code: 12056050
Display: It is necessary to manually eject the tray.
Used by: QP3
Cause: Unable to eject empty tray. The vacuum supply is already ON,
and the tray that was picked up has been dropped, preventing
automatic tray rejection form being performed.
Remedy: Open the MTU door and remove the empty tray from the shuttle.
Check the status of the empty tray as there is a possibility of
interference if the tray is not lying properly when returning
the shuttle to its retract position.
------------------------------
第 581 页
Code: 12056051
Display: Empty tray removal interruption
Used by: QP3
Cause: The empty tray removal process has been interrupted.
Remedy: There is no need to remove the empty tray as it will be
removed automatically upon recommencing auto operation.
If the tray is manually removed, it is necessary to specify the pick-up position.
In the case where the pick-up position is specified,
the empty tray is not automatically removed when recommencing auto operation.
------------------------------
Code: 12056052
Display: Nozzle shutter open/close confirmation error
Used by: QP3
Cause: The nozzle shutter position cannot be determined because both the open and close sensors are
on.
Remedy: Ensure that the open and close sensors are working properly.Check the I/O displayed in the
parameter section.
------------------------------
Code: 12056054
Display: 载入侧搬运轨道转载传感器异常
Used by: NXTP
Cause: 1.电路板较薄，转载传感器不能检出搬运中的电路板，到达传感器ON了。
2.转载传感器调整不良
3.到达传感器误检出电路板以外（例.电路板挡块）。
Remedy: 1.如果搬运轨道内有电路板，请调整转载传感器。
2.如果搬运轨道内没有电路板，请调整电路板到达传感器。
<img src="$LKEY_ERRIMG_MC$/12056054.PNG">
------------------------------
Code: 12056055
Display: 通道2转载传感器逻辑异常
Used by: NXTP
Cause: 1.电路板较薄，转载传感器不能检出搬运中的电路板，到达传感器ON了。
2.转载传感器调整不良
3.到达传感器误检出电路板以外（例.电路板挡块）。
Remedy: 1.如果搬运轨道内有电路板，请调整转载传感器。
2.如果搬运轨道内没有电路板，请调整电路板到达传感器。
<img src="$LKEY_ERRIMG_MC$/12056055.PNG">
------------------------------
Code: 12056056
Display: 往复臂转载传感器逻辑异常
Used by: NXTP
Cause: 1.转载传感器不能检出搬运中的电路板，到达传感器ON了。
2.转载传感器调整不良
3.到达传感器误检出电路板以外（例.电路板挡块）。
Remedy: 1.如果搬运轨道内有电路板，请调整转载传感器。
2.如果搬运轨道内没有电路板，请调整电路板到达传感器。
------------------------------
Code: 12056057
Display: 基座位置不正确
Used by: NXTP
Cause: 拉出基座，在拉入指令中，基座位置不正确。
第 582 页
Remedy: 请取得发生错误时的跟踪数据，与本公司电话服务中心联络。
<img src="$LKEY_ERRIMG_MC$/12056057.PNG">
------------------------------
Code: 12056058
Display: 机内无电路板
Used by: NXTP
Cause: 执行机内(主搬运轨道)电路板的使用指令时没有发现电路板。
Remedy: 请打开门并放入电路板。
<img src="$LKEY_ERRIMG_MC$/EI0084.png">
------------------------------
Code: 12056059
Display: 主搬运轨道的换乘传感器异常
Used by: GPX-C
Cause: 1.用于检测换乘过程的传感器未检测出搬运中的电路板，但是用于检测抵达的传感器发生感应了
2.换乘传感器的调试不良
3.抵达传感器误将电路板以外的零部件等（例.电路板挡块）当作电路板发生感应了
Remedy: 1.如果搬运轨道内有电路板，则请对换乘传感器进行调整
2.如果搬运轨道内没有电路板，则请对抵达传感器进行调整
------------------------------
Code: 1205605A
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1205605B
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1205605C
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 12056101
Display: Interlock X Tramsfer
Used by:
Cause: Movement of the frame in the X direction may be interfering with the manual cleaning lifter or the
S axis.
Remedy: If it is the manual cleaning lifter, move the frame to the left or to the right and then re-execute
the command. If it is the S axis, move the screen to the left and then re-execute the command.
------------------------------
Code: 12056102
Display: Interlock Screen Lift
Used by:
Cause: The manual cleaning lifter may be interfering with X direction movement of the frame or the S
axis.
Remedy: After moving the manual cleaning lifter to its down position, re-execute the command.
第 583 页