FUJI错误代码查询.pdf - 第573页

Code: 1205501A Display: Pressure measurement file error. Used by: NP-2, QP-3 Cause: Cannot read the pressure measurement file. Remedy: Inspect the condition of the hard disk. It may be full or damaged. ------------------…

Remedy: Check that a back-up pin is not contacting parts on the lower surface of the board. Unload the

board if parts are being contacted, otherwise resumu operation after adjusting the position of the board.

------------------------------

Code: 12055012

Display: Vision processing has been aborted.

Used by: NP2,QP3

Cause: The execution of vision processing has been aborted.

Remedy: Restart the machine. Contact Fuji if this problem occurs even after the machine is restarted.

------------------------------

Code: 12055013

Display: Data error!

Used by: NP2,QP3

Cause: Internal data error!

Remedy: Restart the machine.

------------------------------

Code: 12055014

Display: Pre-allocated sequence error!

Used by: NP2,QP3

Cause: Pre-allocated sequence error!

Remedy: Check the production program, unload the PCB and restart the machine.

------------------------------

Code: 12055015

Display: Pressure measurement file error.

Used by: NP-2, QP-3

Cause: Cannot create pressure measurement file.

Remedy: Inspect the condition of the hard disk. It may be full or damaged.

------------------------------

Code: 12055016

Display: Pressure measurement file error.

Used by: NP-2, QP-3

Cause: Cannot open pressure measurement file.

Remedy: Inspect the condition of the hard disk. It may be full or damaged.

------------------------------

Code: 12055017

Display: Pressure measurement file error.

Used by: NP-2, QP-3

Cause: Cannot close pressure measurement file.

Remedy: Inspect the condition of the hard disk. It may be full or damaged.

------------------------------

Code: 12055018

Display: Pressure measurement file error.

Used by: NP-2, QP-3

Cause: Cannot change the name of the pressure measurement file.

Remedy: Inspect the condition of the hard disk. It may be full or damaged.

------------------------------

Code: 12055019

Display: Pressure measurement file error.

Used by: NP-2, QP-3

Cause: Cannot write to the pressure measurement file.

Remedy: Inspect the condition of the hard disk. It may be full or damaged.

------------------------------

第 572 页

Code: 1205501A

Display: Pressure measurement file error.

Used by: NP-2, QP-3

Cause: Cannot read the pressure measurement file.

Remedy: Inspect the condition of the hard disk. It may be full or damaged.

------------------------------

Code: 1205501B

Display: 没有进行周期自动补正的有效的吸嘴。

Used by: XP141,XP241,XP341,XP142,XP242

Cause: 没有进行周期自动补正的有效的吸嘴。

Remedy: 请安装能够进行周期自动补正的吸嘴。

------------------------------

Code: 12055026

Display: 周期自动补正超过了补正容许范围。

请用测定回转中心指令进行测定。

Used by: XP141,XP241,XP341,XP142,XP242

Cause: 周期自动补正值超过了补正公差值。

Remedy: 请用测定回转中心指令进行测定。

------------------------------

Code: 12055027

Display: Double placement error

Used by: QP3

Cause: A sequence that has already been completed has been specified. Parts may be placed on top of

one another.

Remedy: Acquire a trace and unload the panel from the machine.

------------------------------

Code: 12055028

Display: 周期自动补正的测定结果超过极限。

Used by: XP142,XP242

Cause: 周期自动补正的测定结果超过极限。

Remedy: 请重新检查极限的下限值和上限值。

------------------------------

Code: 12056001

Display: "Nozzle type alarm" (CP4), "ST17 nozzle type detection error: HEAD?"

(CP6)

Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643

Cause: When this error occurs on a CP4, none of the nozzle type check sensors has turned on.On a CP6,

a nozzle type check (ST17) indicated a nozzle type other than 1 through 6.

Remedy: On a CP4, adjust ST10 and ST11 so that the sensors can detect the nozzle type. If this error

seems to occur with no specific nozzle on a CP6, check the adjustment of the nozzle type detection sensor.

If it tends to occur with a specific nozzle, inspect the nozzle detection locations for the specified head.

------------------------------

Code: 12056002

Display: "Nozzle change error"

Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643

Cause: The results of a nozzle change check (ST11) indicate a different nozzle type than that remembered

by the machine.On the CP6, this error is reported when a nozzle type check (ST19) performed after a

nozzle change (ST18) indicates a nozzle type other than 1 through 6. This error may also occur if the

nozzle has been changed to a type other than the targeted type.

Remedy: Check the holder, or adjust the nozzle type check sensor.If this error seems to occur with no

specific nozzles on a CP6, check the adjustment of the nozzle type detection sensor. If it tends to occur

第 573 页

with a specific nozzle, inspect the nozzle detection locations for the specified head.

------------------------------

Code: 12056003

Display: 侧夹紧传感器逻辑异常

Used by: GSP5,GP551,GP6,GPX,GPX-C

Cause: 侧松开传感器或侧夹紧正常传感器的输入在逻辑上变得不正常。(GSP5) 即使电路板松开，侧夹紧落空确认传

感器也没有ON。 (GPX)

Remedy: 请进行侧松开传感器或侧夹紧正常传感器的调整／更换，使之变成以下的逻辑。

电路板松开时正常夹紧时夹紧失败时

松开 ○ × ×

正常夹紧 ○ ○ ×（GSP5）１．请确认是否有妨碍了侧夹紧动作的落下电路板等的

存在。

２．什么也没有时，需要进行电路板侧夹紧落空确认传感器(GPX:RX006,GPX-C:IN10)的调整。（请与本公司的

Support联系）（GPX,GPX-C)

------------------------------

Code: 12056004

Display: Sldr unit Position Error

Used by: GSP5

Cause: The position of the automatic paste dispenser is unacceptable.

Remedy: The adjustment of the sensor is probably incorrect. Adjust the sensor so that it corresponds

with the position of the automatic paste dispenser.

------------------------------

Code: 12056005

Display: Wrong Sqg Pres Data

Used by: GSP5

Cause: This error occurs only when the print pressure feedback option is in use.When measuring the

print pressure, a Low signal which was higher than the Hi signal was detected. This indicates that there

is an error in the Hi/Low logic specified in the print comparator. Furthermore, the low signal (X072 SQG

PRES LO) may be short circuited to GB.

Remedy: The print pressure input logic must be specified in the following manner: Hi is greater than

Low.Check that the high/low wiring is correct (GSP5). The pressure change/time gradient is too

steep.Adjust the Pressure/Time control item in Proper data to give a less steep gradient.

------------------------------

Code: 12056006

Display: M/C err Sqg Pres Range Over

Used by: GSP5,GP2,GP3,GP551,GP6

Cause: This error occurs only when print pressure feedback is being used. Although the control pressure

dropped below 0% or exceeded 100% when print pressure feedback was being used, the print pressure did

not automatically return to the specified range.

Remedy: The print pressure input logic must be specified in the following manner: Hi is greater than

Low.The printing height may be too low or there may be something between the screen and the board

(GSP5).

------------------------------

Code: 12056007

Display: Error : PPC origin positon sensor

Used by: IP3

Cause: During calibration the reference position check sensor did not come on when parts were being

placed, or the sensor was already on when operation began.

Remedy: At the I/O map check that the reference position check sensor turns on and off

correctly.Furthermore, check the sensor and the nozzle if the sensor is on even when the nozzle is not

第 574 页