FUJI错误代码查询.pdf - 第126页

Remedy: When using the MCS, set Pcb_x in the production program. When using F4G, check the value of General PCB Data X. Refer to the board length in the FQP1. In order to position the board in the pallet, the correct boa…

Display: 与编码相同

Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP

Cause: 焊锡供应计数在范围之外。

Remedy: 请确认生产程序的Ｓｏｌｄｅｒ＿ｓｕｐｐｌｙ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认

Ｓｏｌｄｅｒ＿ｓｕｐｐｌｙ＿ｉｎｔｅｒｖａｌ）。范围是０～６５０００[块](如果是ＧＳＰ５时，范围是

０～６００００[块])。请确认在ＦｕｊｉＦｌｅｘａ上设定的焊锡供应计数。范围是０～９９９９［块］。

（GPX,NXTP）

------------------------------

Code: 1101E022

Display:

Used by: GSP5

Cause: The solder viscosity is out of range.

Remedy: Check solder_viscsty in the production program. The range is 1 to 60 [*10 Pa.s]

------------------------------

Code: 1101E023

Display:

Used by: GSP5

Cause: The solder supply one-way count is out of range.

Remedy: Check solder_supply_times in the production program. The range is 1 to 10.

------------------------------

Code: 1101E024

Display: 与编码相同

Used by: GSP5,GP551,GP6,GPX,NXTP

Cause: 手动清洁计数器在范围之外。

Remedy: 请确认生产程序的ｍａｎｕａｌ＿ｃｌｅａｎｉｎｇ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认

ｍａｎｕａｌ＿ｃｌｅａｎｉｎｇ＿ｉｎｔｅｒｖａｌ）。范围是０～６５０００[块]。请确认在

ＦｕｊｉＦｌｅｘａ上设定的手动清洁计数。范围为０～９９９９［块］。（GPX,NXTP）

------------------------------

Code: 1101E025

Display: 与编码相同

Used by: GSP5,GPX,NXTP

Cause: 清洁速度超出范围。

Remedy: 请确认生产程序的ｃｌｅａｎｉｎｇ＿ｓｐｅｅｄ。

范围:从１０到２００［ｍｍ／ｓｅｃ］

请确认在FujiFlexa设定的清洁速度。

范围:从１到３００［ｍｍ／ｓｅｃ］(GPX)

范围:从１０到３００［ｍｍ／ｓｅｃ］(NXTP)

------------------------------

Code: 1101E026

Display: 与编码相同

Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP

Cause: 虽然存在不使用侧夹紧的生产（65.Side_clamp为ＯＦＦ），25.Vacuum_flag不是

ALL_ON，68.Use_vacuum也没有被指定。(GSP5)

侧夹紧OFF时，请将电路板真空ON。(GPX,NXTP)

Remedy: 请检查生产程序的65.Side_Clamp,25.Vacuum_flag,68.Use_vacuum。请确认

FujiFlexa上的侧夹紧设定和电路板真空设定。(GPX,NXTP)

------------------------------

Code: 1101E027

Display: 1101E027

Used by: QP132

Cause: The board length is not specified (FQP1).

第 125 页

Remedy: When using the MCS, set Pcb_x in the production program. When using F4G, check the value of

General PCB Data X. Refer to the board length in the FQP1. In order to position the board in the pallet,

the correct board length (tolerance within +-0.5 mm) must be specified.

------------------------------

Code: 1101E028

Display: 1101E028

Used by: QP132

Cause: The board width is not specified (FQP1).

Remedy: When using the MCS, set Pcb_y in the production program. When using F4G, check the value of

General PCB Data Y. If a board with a different width is detected on the FQP1 it is unloaded. For this

reason the board width must be entered. Board width is judged to be different if the current board width

differs from the previous board width by more than +-0.5 mm.

------------------------------

Code: 1101E029

Display: 1101E029

Used by: QP132

Cause: The board thickness is not specified (FQP1).

Remedy: When using F4G, check the value of General PCB Data Thickness in the production program.

On the FQP1, the reference point for the pickup nozzles is taken as the lower surface of the board.

Therefore, the board thickness must be input.

------------------------------

Code: 1101E02A

Display: Same as code

Used by: QP132

Cause: The rotation angle specified for board setup in the program header is outside the valid range.

This error occurs when the program is checked upon transmission.

Remedy: Set the rotation angle for board setup in the program header to 0 to load the board without

rotation, or 3 to load with rotation.

------------------------------

Code: 1101E02B

Display: Same as code

Used by: QP132

Cause: The multiple board loading flag in the program header is outside the valid range. This error

occurs when the program is checked upon transmission.

Remedy: Set the multiple board loading flag in the program header to 0 or 1 when loading a single board,

or to 2 for tandem loading.

------------------------------

Code: 1101E02C

Display: Same as code

Used by: QP132

Cause: The number of blocks per board has not been set even though the multiple board loading flag in

the program header indicates that tandem loading is to be performed. This error occurs when the

program is checked upon transmission.

Remedy: Set the number of blocks per board when the multiple board loading flag in the program header

indicates that tandem loading is to be performed.

------------------------------

Code: 1101E02D

Display: Same as code

Used by: QP132

Cause: The value of the indexing type parameter in the program header is outside the valid range. This

error occurs when the program is checked upon transmission.

第 126 页

Remedy: Set the indexing type in the program header to one of the following values: 0, 2, 3, 4, or 5. These

settings indicate 7-inch indexing, 5-2 indexing, 4-3 indexing, 3-4 indexing, and 2-5 indexing, respectively.

------------------------------

Code: 1101E02E

Display: Same as code

Used by: QP132

Cause: Different indexing types are specified for programs having the same family name.

Remedy: Change the family name, or set the indexing types to the same value.

------------------------------

Code: 1101E02F

Display: Same as code

Used by: QP132

Cause: Unexecutable sequences have occurred because the indexing type in the program header has

been set to 7-inch single indexing. This error occurs when the program is checked upon transmission.

Remedy: Check the mounting coordinates in the sequence data. If the coordinates are correct, set the

indexing type in the program header to a value other than 0.

------------------------------

Code: 1101E030

Display: Same as code

Used by: QP132

Cause: A family name has not been set in the program header. This error occurs when the program is

checked upon transmission.

Remedy: Set a family name in the program header.

------------------------------

Code: 1101E031

Display: Same as Code.

Used by: QP132

Cause: The value set for the loading distance position for tandem loading ("PCB distance") has been set to

a positive value.

Remedy: Set this item to a negative value.

------------------------------

Code: 1101E032

Display: 与编码相同

Used by: GP551,GP6,GPX,NXTP

Cause: 特殊清洁计数器超出范围。

Remedy: 请确认生产程序的Ｓｐｅｃｉａｌ＿ｃｌｅａｎｉｎｇ＿ｉｎｔｅｒｖａｌ。

范围:0～65000［块］

请确认FujiFlexa上设定的特殊自动清洁计数器。

范围:0～9999[块](GPX,NXTP)

自动清洁为0块时，不能对特殊清洁进行1块以上的设定(GPX,NXTP)。

------------------------------

Code: 1101E033

Display: Same as code

Used by: GP2,GP3,GP551,GP6

Cause: The pressure measurement interval setting is outside the valid range.

Remedy: Make sure that the "Press_meas_interval" parameter in the production program is set to a value

from 0 to 65000 [boards].

------------------------------

Code: 1101E034

Display: Same as code

Used by: GP551,GP6

第 127 页