FUJI错误代码查询.pdf - 第558页

Used by: CP652C Cause: Either the shutter between the UP elevator and the PPS6 was open when the UP elevator started moving, or it opened during UP elevator operation. Remedy: Make sure the UP elevator shutter is closed.…

Code: 12054074

Display: "Pal Transport Err OUT->DOWNELV"

Used by: CP652C

Cause: Either the forward end check sensor for the cylinder of the pallet conveyor between the OUT

position and the DOWN elevator has not turned on even though the specified time has elapsed since the

cylinder was instructed to start moving, or the pallet movement complete status was not achieved when

the forward end check sensor turned on. "Pallet movement complete status" is as follows: when the pallet

OUT cylinder forward end check sensor turns on, the pallet OUT cylinder retract end check sensor sho ld

be off, the OUT position pallet check sensor should be on, the DOWN elevator pallet check sensor should

be off, and the DOWN elevator pallet passage check sensor should be on.

Remedy: Make sure that nothing is obstructing pallet movement. If there is no obstruction, perform an

I/O check on the input from the following sensors: pallet OUT cylinder forward end check (X0A8) and

retract end check (X0A9), OUT position pallet check (X047), DOWN elevator pallet check (X0A4), and

DOWN elevator pallet passage check (X0A5). Adjust the sensors as necessary.

------------------------------

Code: 12054075

Display: "Pal Transport Err DOWNELV->RCONV"

Used by: CP652C

Cause: The forward end check sensor for the cylinder of the pallet conveyor between the DOWN elevator

and the return conveyor has not turned on even though the specified time has elapsed since the cylinder

was instructed to start moving, or the pallet movement complete status was not achieved when the

forward end check sensor turned on. "Pallet movement complete status" is as follows: when the return

conveyor pallet IN cylinder forward end check sensor turns on, the return conveyor pallet IN cylinder re

ract end check sensor should be off, the return conveyor full sensor should be on, the DOWN elevator full

sensor should be on, the DOWN elevator pallet check sensor should be off, and the DOWN elevator pallet

passage check sensor should be on.

Remedy: Make sure that nothing is obstructing pallet movement. If there is no obstruction, perform an

I/O check on the input from the following sensors: return conveyor pallet IN cylinder forward end check

(X09C) and retract end check (X09D), return conveyor full (X09F), DOWN elevator pallet check (X0A4), and

DOWN elevator pallet passage check (X0A5). Adjust the sensors as necessary.

------------------------------

Code: 12054076

Display: "PAL.OUT Cylinder Time Out"

Used by: CP652C

Cause: Either the retract end check sensor for the pallet OUT cylinder has not turned on even though the

specified time has elapsed since the cylinder was instructed to start retracting, or both the forward end

and retract end check sensors have turned on.

Remedy: Make sure that nothing is obstructing operation. If there is no obstruction, perform an I/O

check on the input from the following sensors: pallet OUT cylinder forward end check (X0A8) and retract

end check (X0A9). Adjust the sensors as necessary.

------------------------------

Code: 12054077

Display: "UP ELV Pallet Stopper is OFF"

Used by: CP652C

Cause: Either the UP elevator pallet stopper or the UP elevator pallet end stopper is off even though the

UP elevator is operating while carrying a pallet.

Remedy: Check the UP elevator pallet stopper sensors (X08C and X08D) and the UP elevator pallet end

stopper sensors (X08A and X08B).

------------------------------

Code: 12054078

Display: "UP ELV Shutter Not Closed"

第 557 页

Used by: CP652C

Cause: Either the shutter between the UP elevator and the PPS6 was open when the UP elevator started

moving, or it opened during UP elevator operation.

Remedy: Make sure the UP elevator shutter is closed.

------------------------------

Code: 12054079

Display: "UP ELV Pal.Stopper Time Out"

Used by: CP652C

Cause: Either a sensor for the UP elevator pallet stopper has not turned on even though the specified

time has elapsed since the stopper was instructed to start operation, or both the stopper ON and OFF

check sensors have turned on.

Remedy: Make sure that nothing is obstructing stopper operation. If there is no obstruction, perform an

I/O check on the input from the following sensors: UP elevator pallet stopper ON (X08C) and OFF (X08D).

Adjust the sensors as necessary.

------------------------------

Code: 1205407A

Display: "UP ELV Pal.END STP Time Out"

Used by: CP652C

Cause: Either an sensor for the UP elevator pallet end stopper has not turned on even though the

specified time has elapsed since the stopper was instructed to start operation, or both the end stopper ON

and OFF check sensors have turned on.

Remedy: Make sure that nothing is obstructing stopper operation. If there is no obstruction, perform an

I/O check on the input from the following sensors: UP elevator pallet end stopper ON (X08A) and OFF

(X08B). Adjust the sensors as necessary.

------------------------------

Code: 1205407B

Display: "PAL IN Cylinder end error"

Used by: CP652C

Cause: The pallet IN cylinder has left the retract end even though the UP elevator is operating while

carrying a pallet.This error could also occur if the retract end check sensor for the pallet INcylinder has

not turned on even though the specified time has elapsed since the cylinder was instructed to start

retracting, or if both the forward end and retract end check sensors have turned on.

Remedy: Make sure that nothing is obstructing operation. If there is no obstruction, perform an I/O

check on the input from the following sensors: pallet IN cylinder forward end check (X088) and retract end

check (X089).Adjust the sensors as necessary.

------------------------------

Code: 1205407C

Display: "SETUP_ST. IN STP. Time Out"

Used by: CP652C

Cause: The in-setup station stopper did not complete its operation in the 3 seconds allowed.

Remedy: Check that there is nothing obstructing the stopper's movement.

Check the I/O signals for the in-setup station stopper's engaged (X090) and disengaged (X091) positions.

------------------------------

Code: 1205407D

Display: "R.Conv Pal Stopper Time Out"

Used by: CP652C

Cause: Either a sensor for the return conveyor pallet stopper has not turned on even though the

specified time has elapsed since the stopper was instructed to start operation, or both the stopper ON and

OFF check sensors have turned on.

Remedy: Make sure that nothing is obstructing stopper operation. If there is no obstruction, perform an

I/O check on the input from the following sensors: return conveyor pallet stopper ON (X098) and OFF

第 558 页

(X099). Adjust the sensors as necessary.

------------------------------

Code: 1205407E

Display: "Pal Transport Err RCONV->UPELV"

Used by: CP652C

Cause: The forward end check sensor for the cylinder of the pallet conveyor between the return conveyor

and the UP elevator has not turned on even though the specified time has elapsed since the cylinder was

instructed to start moving, or the pallet movement complete status was not achieved when the forward

end check sensor turned on."Pallet movement complete status" is as follows: when the return conveyor

pallet OUT cylinder forward end check sensor turns on, the return conveyor pallet OUT cylinder re ract

end check sensor should be off, the return conveyor pallet arrival check sensor should be off, the UP

elevator pallet check sensor should be on, and the UP elevator pallet passage check sensor should be on.

Remedy: Make sure that nothing is obstructing pallet movement. If there is no obstruction, perform an

I/O check on the input from the following sensors: return conveyor pallet OUT cylinder forward end check

(X09A) and retract end check (X09B), return conveyor pallet arrival check (X09E), UP elevator pallet check

(X084), and UP elevator pallet passage check (X085). Adjust the sensors as necessary.

------------------------------

Code: 1205407F

Display: "Pallet_Clamp Error DF or DR"

Used by: CP652C

Cause: The DF-axis (or DR-axis) has failed to clamp a pallet, or a clamp status check performed during

DF-axis (or DR-axis) operation has shown that a pallet is not clamped properly.

Remedy: Make sure that the DF-axis and DR-axis clamps are functioning normally. Perform I/O checks

on input from the following sensors: pallet clamp check (X058 and X05B), pallet unclamp check (X059and

X05C), and pallet check (X05A and X05D) for the DF-axis and DR-axis. Adjust the sensors as necessary.

When a pallet is clamped, the sensors for that axis should be as follows: the pallet clamp and pallet check

sensors should be on, and the pallet unclamp check sensor should be off.

------------------------------

Code: 12054080

Display: " R.Conv IN(OUT) Cylinder Time Out"

Used by: CP652C

Cause: Either the retract end check sensor for the return conveyor pallet IN or OUT cylinder has not

turned on even though the specified time has elapsed since the cylinder was instructed to start retracting,

or both the forward end and retract end check sensors have turned on.

Remedy: Make sure that nothing is obstructing cylinder operation.If there is no obstruction, perform an

I/O check on the input from the following sensors: return conveyor pallet IN and OUT cylinderforward end

check (X09A and X09C) and retract end check (X09B and X09D). Adjust the sensors as necessary.

------------------------------

Code: 12054081

Display: "Pallet_Unclamp Error DF or DR"

Used by: CP652C

Cause: The DF-axis (or DR-axis) has failed to unclamp a pallet.

Remedy: Make sure that the DF-axis and DR-axis unclamp operation is functioning normally.Perform I/O

checks on input from the following sensors: pallet clamp check (X058 and X05B), pallet unclamp check

(X059 and X05C), and pallet check (X05A and X05D) for the DF-axis and the DR-axis. Adjust the sensors

as necessary. When a pallet is unclamped, the sensors for that axis should be as follows: the pallet clamp

and pallet check sensors should be off, and the pallet unclamp check sensor should be on.

------------------------------

Code: 12054082

Display: "ST11:Nozzle up/down error.", "ST11:Check cylinder." (CP6,6M)]

Used by: CP6,CP643

第 559 页