FUJI错误代码查询.pdf - 第1080页

Remedy: If the application amount is unstable, stabilize it by adjusting parameters such as the application pressure, the application time(the Apply Volume), the lower limit timer, and the lower limit height. If glueappl…

Used by: GL2,GL5

Cause: The color of the first search point is the color specified in GL2 Glue Black0 or White1, but the

edge of the glue dot could not be found.

Remedy: If the glue dot application is not stable, adjust the application pressure, application time, lower

position timer, lower position height, etc. If the application is stable, check that the vision processing

system is taking the image correctly. If it isnlt, check the CCD level and the GL2 Glue Black0 or Whitel

setting. Refer to the FCP-II Operation Manual for further details.

------------------------------

Code: 14030002

Display: er0002

Used by: GL2,GL5

Cause: The color of the first search point is not the color specified in GL2 Glue Black0 or White1, but the

edge of the glue dot could not be found.

Remedy: If the glue dot application is not stable, adjust the application pressure, application time, lower

position timer, lower position height, etc. If the application is stable, check that the vision processing

system is taking the image correctly. If it isnlt, check the CCD level and the GL2 Glue Black0 or Whitel

setting. Refer to the FCP-II Operation Manual for further details.

------------------------------

Code: 14030003

Display: er0003

Used by: GL2,GL5

Cause: The size of the glue dot is too big for the edge to be detected.

Remedy: If the glue dot application is not stable, adjust the application pressure, application time, lower

position timer, lower position height, etc. If the application is stable, check that the vision processing

system is taking the image correctly. If it isnlt, check the CCD level and the GL2 Glue Black0 or Whitel

setting. Refer to the FCP-II Operation Manual for further details.

------------------------------

Code: 14030004

Display: er0004

Used by:

Cause: Noise was discovered, or neighboring dots are too close to distinguish between them.

Remedy: If the application is stable, check that the vision processing system is taking the image correctly.

If it isn't, check the CCD level and the GL2 Glue Black0 or Whitel setting. Refer to the FCP-II Operation

Manual for further details.

------------------------------

Code: 14030005

Display: er0005

Used by: GL2,GL5,GL541,(QP3)

Cause: The glue application point is too large.

Remedy: If the application amount is unstable, stabilize it by adjusting parameters such as the

application pressure, the application time(the Apply Volume), the lower limit timer, and the lower limit

height. If glueapplication is normal, make sure that the image is scanned correctly. If the image is not

scanned correctly, check the CCD level and the "GL2 Glue Black0 or White1" parameter in the program's

headerdata(check the CCD level and the "Mark Color" parameter in the program). (For details, see

Chapter 3, "Automatic operation and programming" and Chapter 2, "Glue checking" in t e FGL-2

Operation Manual.)

------------------------------

Code: 14030006

Display: er0006

Used by: GL2,GL5,GL541,(QP3)

Cause: The glue application point is too small.

第 1079 页

Remedy: If the application amount is unstable, stabilize it by adjusting parameters such as the

application pressure, the application time(the Apply Volume), the lower limit timer, and the lower limit

height. If glueapplication is normal, make sure that the image is scanned correctly. If the image is not

scanned correctly, check the CCD level and the "GL2 Glue Black0 or White1" parameter in the program's

headerdata(check the CCD level and the "Mark Color" parameter in the program). (For details, see

Chapter 3, "Automatic operation and programming" and Chapter 2, "Glue checking" in t e FGL-2

Operation Manual.)

------------------------------

Code: 14030010

Display: er0010

Used by: GL2,GL5

Cause: The center space between two application points at 0[deg] and 180[deg] is too large.

Remedy: If the application amount is unstable, stabilize it by adjusting parameters such as the

application pressure, the application time, the lower limit timer, and the lower limit height. If

glueapplication is normal, make sure that the image is scanned correctly. If the image is not scanned

correctly, check the CCD level and the "GL2 Glue Black0 or White1" parameter in the program's

headerdata. (For details, see Chapter 3, "Automatic operation and programming" and Chapter 2, "Glue

checking" in t e FGL-2 Operation Manual.)

------------------------------

Code: 14030011

Display: er0011

Used by: GL2,GL5,GL541

Cause: One of two application points at 0[deg] and 180[deg] is smaller than the other. (It is smaller than

the diameter of the larger point, minus the amount specified by the "Glue check limit" parameter.)

Remedy: If the application amount is unstable, stabilize it by adjusting parameters such as the

application pressure, the application time, the lower limit timer, and the lower limit height. If

glueapplication is normal, make sure that the image is scanned correctly. If the image is not scanned

correctly, check the CCD level and the "GL2 Glue Black0 or White1" parameter in the program's

headerdata. (For details, see Chapter 3, "Automatic operation and programming" and Chapter 2, "Glue

checking" in t e FGL-2 Operation Manual.)

------------------------------

Code: 14030012

Display: er0012

Used by: GL2,GL5

Cause: The center is too large for a 90 deg. or 270 deg. double-dot application.

Remedy: If the glue dot application is not stable, adjust the application pressure, application time, lower

position timer, lower position height, etc. If the application is stable, check that the vision processing

system is taking the image correctly. If it isnlt, check the CCD level and the GL2 Glue Black0 or Whitel

setting. Refer to the FCP-II Operation Manual for further details.

------------------------------

Code: 14030013

Display: er0013

Used by: GL2,GL5,GL541

Cause: One of two application points at 90[deg] and 270[deg] is smaller than the other. (It is smaller

than the diameter of the larger point, minus the amount specified by the "Glue check limit" parameter.)

Remedy: If the application amount is unstable, stabilize it by adjusting parameters such as the

application pressure, the application time, the lower limit timer, and the lower limit height. If

glueapplication is normal, make sure that the image is scanned correctly. If the image is not scanned

correctly, check the CCD level and the "GL2 Glue Black0 or White1" parameter in the program's

headerdata. (For details, see Chapter 3, "Automatic operation and programming" and Chapter 2, "Glue

checking" in t e FGL-2 Operation Manual.)

第 1080 页

------------------------------

Code: 14040001

Display: 14040001

Used by:

Cause: The nozzle could not be found.

Remedy: Check the condition under which parts are being supplied.

------------------------------

Code: 14040002

Display: 14040002

Used by:

Cause: The image was not correctly acquired. The unevenness on the top or bottom of the part is

excessive. There may be a foreign object on the nozzle.

Remedy: Check the camera, the vision processing board, the cable, and the focus. Remove any foreign

objects from the nozzle.

------------------------------

Code: 14040003

Display: 14040003

Used by:

Cause: The image was not correctly acquired. The unevenness on the top or bottom of the part is

excessive. There may be a foreign object on the nozzle.

Remedy: Check the camera, the vision processing board, the cable, and the focus. Remove any foreign

objects from the nozzle.

------------------------------

Code: 14040004

Display: 14040004

Used by:

Cause: The image was not correctly acquired. The unevenness on the top or bottom of the part is

excessive. There may be a foreign object on the nozzle.

Remedy: Check the camera, the vision processing board, the cable, and the focus. Remove any foreign

objects from the nozzle.

------------------------------

Code: 14040005

Display: 14040005

Used by:

Cause: The image was not correctly acquired. The unevenness on the top or bottom of the part is

excessive. There may be a foreign object on the nozzle.

Remedy: Check the camera, the vision processing board, the cable, and the focus. Remove any foreign

objects from the nozzle.

------------------------------

Code: 14040006

Display: 14040006

Used by:

Cause: The image was not correctly acquired. The unevenness on the top or bottom of the part is

excessive. There may be a foreign object on the nozzle.

Remedy: Check the camera, the vision processing board, the cable, and the focus. Remove any foreign

objects from the nozzle.

------------------------------

Code: 14040007

Display: 14040007

Used by:

Cause: The image was not correctly acquired. The unevenness on the top or bottom of the part is

第 1081 页