FUJI错误代码查询.pdf - 第2110页

Used by: Cause: The print file could not be created. Remedy: Check the RAM for previously created files and for remaining memory. Re-boot MCS. ------------------------------ Code: 2100FA07 Display: change console path er…

100%1 / 5282
Code: 2100F050
Display: Sequence(Z) count over.
Used by:
Cause: An error occurred when performing a snap-off sequence check.
Remedy: Edit the file to ensure that the number of board snap-off sequences is less than 10.
------------------------------
Code: 2100F051
Display: Sequence(Z) : X data is out of order.
Used by:
Cause: An error occurred when performing a snap-off sequence check.
Remedy: Edit the relevant file using the editor to ensure that the X coordinates of the snap-off sequences
are ranked in ascending order.
------------------------------
Code: 2100FA00
Display: can't read strings file
Used by:
Cause: The prop_str.E file cannot be loaded into the memory.
Remedy: Re-boot MCS. If the error recurs, re-install the system.
------------------------------
Code: 2100FA01
Display: Syntax error - Illegal '+' option
Used by:
Cause: The + option was not specified correctly at start-up.
Remedy: If this error occurred during a direct command, correct the input command.
------------------------------
Code: 2100FA02
Display: Syntax error - illegal '-' option
Used by:
Cause: The '-' option was not specified correctly at start-up.
Remedy: Correct the input command if this error occurred due to a direct command.
------------------------------
Code: 2100FA03
Display: Syntax error - check file not found
Used by:
Cause: The specified object file does not exist.
Remedy: Correct the name of the specified object file.
------------------------------
Code: 2100FA04
Display: not found - check file on disk
Used by:
Cause: The specified file does not exist.
Remedy: Correct the filename.
------------------------------
Code: 2100FA05
Display: can't create output file
Used by:
Cause: Output file could not be created.
Remedy: Check the RAM for previously created files and for remaining memory. Re-boot MCS.
------------------------------
Code: 2100FA06
Display: can't create print file
第 2109 页
Used by:
Cause: The print file could not be created.
Remedy: Check the RAM for previously created files and for remaining memory. Re-boot MCS.
------------------------------
Code: 2100FA07
Display: change console path error
Used by:
Cause: The terminal path could not be selected during start-up.
Remedy: Check the RAM for previously created files and for remaining memory. Re-boot MCS.
------------------------------
Code: 2100FA08
Display: CRT event link error
Used by:
Cause: The terminal event could not be linked.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100FA09
Display: can't load proper file on memory
Used by:
Cause: The specified file cannot be loaded into memory.
Remedy: Reboot MCS or re-install the system.
------------------------------
Code: 2100FA0A
Display: can't load file descriptor on memory
Used by:
Cause: The file descriptor could not be loaded into memory.
Remedy: Re-boot MCS. If the error recurs, re-install the system.
------------------------------
Code: 2100FA0B
Display: this file is not proper
Used by:
Cause: The specified file is not a Proper data file.
Remedy: Specify the correct file.
------------------------------
Code: 2100FA0C
Display: can't open Lp pipe
Used by:
Cause: The Lp pipe could not be opened.
Remedy: Re-boot MCS.
------------------------------
Code: 2100FA0D
Display: check flag rewrite error
Used by:
Cause: The check flag could not be re-written.
Remedy: Check that the file overwrite protector is not set to prevent overwriting.
------------------------------
Code: 2100FA0E
Display: Proper data NO. %d over range
Used by:
Cause: The **** Proper data item is out of range.
Remedy: Reset the item in question so that it is no longer out of range.
第 2110 页
------------------------------
Code: 2100FA0F
Display: '+' option not found
Used by:
Cause: The '+' option was not found at start-up.
Remedy: Correct the input command if this error occurred due to a direct command.
------------------------------
Code: 2100FA10
Display: Proper for this M/C type is not supported
Used by:
Cause: The specified machine type is not supported.
Remedy: Specify the correct machine type.
------------------------------
Code: 2100FA11
Display: check flag read error
Used by:
Cause: The check flag data could not be read.
Remedy: Use the editor to check that the file is correct.
------------------------------
Code: 2100FA12
Display: Default value is used if no data is entered
Used by:
Cause: The program structure and descriptor structure are different.
Remedy: This is a warning. Correct and save the file using the editor.
------------------------------
Code: 2100FE00
Display: can't read strings file
Used by:
Cause: The string file (Ntchk_str.E) cannot be loaded into memory.
Remedy: Restart MCS or reinstall the system.
------------------------------
Code: 2100FE01
Display: not found '+' opition
Used by:
Cause: The '+' option was not found during startup.
Remedy: If this occurred during startup by direct command, check that the input command was correct.
------------------------------
Code: 2100FE02
Display: Syntax error - illegal '+' option
Used by:
Cause: The '+' option was not found during startup.
Remedy: If this occurred during startup by direct command, check that the input command was correct.
------------------------------
Code: 2100FE03
Display: Syntax error - not found check file
Used by:
Cause: The check object file has not been specified.
Remedy: Specify the filename.
------------------------------
Code: 2100FE04
Display: not found check file on disk
第 2111 页