FUJI错误代码查询.pdf - 第583页

Remedy: 请取得发生错误时的跟踪数据，与本公司电话服务中心联络。 <img src="$LKEY_ERRIMG_MC$/12056057.PNG"> ------------------------------ Code: 12056058 Display: 机内无电路板 Used by: NXTP Cause: 执行机内(主搬运轨道)电路板的使用指令时没有发现电路板。 Remedy: 请打开门并放…

Code: 12056051

Display: Empty tray removal interruption

Used by: QP3

Cause: The empty tray removal process has been interrupted.

Remedy: There is no need to remove the empty tray as it will be

removed automatically upon recommencing auto operation.

If the tray is manually removed, it is necessary to specify the pick-up position.

In the case where the pick-up position is specified,

the empty tray is not automatically removed when recommencing auto operation.

------------------------------

Code: 12056052

Display: Nozzle shutter open/close confirmation error

Used by: QP3

Cause: The nozzle shutter position cannot be determined because both the open and close sensors are

on.

Remedy: Ensure that the open and close sensors are working properly.Check the I/O displayed in the

parameter section.

------------------------------

Code: 12056054

Display: 载入侧搬运轨道转载传感器异常

Used by: NXTP

Cause: 1.电路板较薄，转载传感器不能检出搬运中的电路板，到达传感器ON了。

2.转载传感器调整不良

3.到达传感器误检出电路板以外（例.电路板挡块）。

Remedy: 1.如果搬运轨道内有电路板，请调整转载传感器。

2.如果搬运轨道内没有电路板，请调整电路板到达传感器。

------------------------------

Code: 12056055

Display: 通道2转载传感器逻辑异常

Used by: NXTP

Cause: 1.电路板较薄，转载传感器不能检出搬运中的电路板，到达传感器ON了。

2.转载传感器调整不良

3.到达传感器误检出电路板以外（例.电路板挡块）。

Remedy: 1.如果搬运轨道内有电路板，请调整转载传感器。

2.如果搬运轨道内没有电路板，请调整电路板到达传感器。

------------------------------

Code: 12056056

Display: 往复臂转载传感器逻辑异常

Used by: NXTP

Cause: 1.转载传感器不能检出搬运中的电路板，到达传感器ON了。

2.转载传感器调整不良

3.到达传感器误检出电路板以外（例.电路板挡块）。

Remedy: 1.如果搬运轨道内有电路板，请调整转载传感器。

2.如果搬运轨道内没有电路板，请调整电路板到达传感器。

------------------------------

Code: 12056057

Display: 基座位置不正确

Used by: NXTP

Cause: 拉出基座，在拉入指令中，基座位置不正确。

第 582 页

Remedy: 请取得发生错误时的跟踪数据，与本公司电话服务中心联络。

------------------------------

Code: 12056058

Display: 机内无电路板

Used by: NXTP

Cause: 执行机内(主搬运轨道)电路板的使用指令时没有发现电路板。

Remedy: 请打开门并放入电路板。

------------------------------

Code: 12056059

Display: 主搬运轨道的换乘传感器异常

Used by: GPX-C

Cause: 1.用于检测换乘过程的传感器未检测出搬运中的电路板，但是用于检测抵达的传感器发生感应了

2.换乘传感器的调试不良

3.抵达传感器误将电路板以外的零部件等（例.电路板挡块）当作电路板发生感应了

Remedy: 1.如果搬运轨道内有电路板，则请对换乘传感器进行调整

2.如果搬运轨道内没有电路板，则请对抵达传感器进行调整

------------------------------

Code: 1205605A

Display:

Used by:

Cause:

Remedy:

------------------------------

Code: 1205605B

Display:

Used by:

Cause:

Remedy:

------------------------------

Code: 1205605C

Display:

Used by:

Cause:

Remedy:

------------------------------

Code: 12056101

Display: Interlock X Tramsfer

Used by:

Cause: Movement of the frame in the X direction may be interfering with the manual cleaning lifter or the

S axis.

Remedy: If it is the manual cleaning lifter, move the frame to the left or to the right and then re-execute

the command. If it is the S axis, move the screen to the left and then re-execute the command.

------------------------------

Code: 12056102

Display: Interlock Screen Lift

Used by:

Cause: The manual cleaning lifter may be interfering with X direction movement of the frame or the S

axis.

Remedy: After moving the manual cleaning lifter to its down position, re-execute the command.

第 583 页

------------------------------

Code: 12056103

Display: Vacuum Holder Too Large

Used by: GP551,GP6

Cause: The size of the board vacuum holder does not match the conveyor width. If the Z-axis is raised

under this condition the conveyor belt will be in danger of being cut.

Remedy: Replace the vacuum holder with one that matches the size of the conveyor width. On the GP6

use the X048 and X049 input signals for verification.

------------------------------

Code: 12056104

Display: 联锁相机Ｚ轴

[Interlock Camera Ｚaxis]

Used by: GP551,GP6,GPX

Cause: 相机与Ｚ轴有可能发生了干涉。在相机移动时Ｚ轴不在待机位置的情况下发生。

Remedy: 请将Ｚ轴移动到待机位置。或者，请确认Ｚ轴待机位置确认传感器的ON/OFF动作。

------------------------------

Code: 12056105

Display: 联锁相机主挡块

[Interlock Camera Main Stopper]

Used by: GP551,GP6,GPX,NXTP

Cause: 安装在相机上的主挡块有可能与其他的部分发生干涉。在下降了主挡块后想要移动相机的情况下发生。

Remedy: 请上升主挡块。或者，请确认ＭＡＩＮ搬运轨道挡块的导入端·退出端的各确认传感器的ON/OFF动作。

------------------------------

Code: 12056106

Display: Interlock Camera Push Plate

Used by: GP551,GP6

Cause: The push plate, attached to the camera, may be damaged in a collision if the push plate is down

and an attempt is made to move the camera.

Remedy: Raise the push plate.Alternatively, check the on/off status of the push plate's up/down position

sensors.

------------------------------

Code: 12056107

Display: InterlockCamera Cleaner

Used by: GP551,GP6

Cause: The camera may collide with the lower cleaner. For GP-5 machines this may occur when the

lower cleaner is not at the origin position. For GP-6 machines, this may occur when the cleaner shift is not

at the retract position.

Remedy: Move the lower cleaner to its origin position (GP-5).For one-sided cleaners, move the cleaner shift

to its retract position (GP-6).Alternatively, check the on/off status of the lower cleaner origin position

sensor, camera and lower cleaner proximity sensor, and the cleaner shift retracted position sensor.

------------------------------

Code: 12056108

Display: Interlock Camera Cleaner Head

Used by: GP551,GP6

Cause: The cleaner head on the cleaner axis may collide with another part. This error occurs if an

attempt is made to move the cleaner axis when the cleaner head is closed.

Remedy: Open the cleaning head. Alternatively, check the on/off status of the cleaner's raised/lowered

sensors (GP-5) or the cleaning head's opened/closed sensors (GP-6).

------------------------------

第 584 页