FUJI错误代码查询.pdf - 第1945页

Code: 2100753B Display: "There is insufficient space for a feeder in PT file" Used by: Cause: An attempt was made to allocate the feeder in question as specified by the PST file, but an error occurred when the …

100%1 / 5282
Display: Output program file name is too long.
Used by:
Cause: The output program filename is too long.
Remedy: Check the filename.
------------------------------
Code: 21007534
Display: Permanent Set Table name is too long
Used by:
Cause: The Permanent Set Table name is too long.
Remedy: Check the filename.
------------------------------
Code: 21007535
Display: Illegal format at Machine type table
Used by:
Cause: The machine type table format is illegal.
Remedy: Re-install the software.
------------------------------
Code: 21007536
Display: "No entry Machine name"
Used by:
Cause: A machine name has not been entered in the "Sep_data" section of the Part data.
Remedy: Enter a machine name and a feeder name in the "Sep_data" section of the Part data.
------------------------------
Code: 21007537
Display: "Couldn*t separate on St.2"
Used by:
Cause: An error occurred as the result of an attempt to allocate a component having a size smaller than
7 mm to Station 2.
Remedy: Components smaller than 7 mm cannot be allocated to Station 2. Specify this component for
fixed allocation to Station 1.
------------------------------
Code: 21007538
Display: "Not PST file"
Used by:
Cause: A file that has been specified as a PST file does not have the ".pst" extension.
Remedy: Specify a PST file as the permanent set table.
------------------------------
Code: 21007539
Display: "Feeder position in PT file is out of range"
Used by:
Cause: A feeder position specified as fixed in the PST file is outside the feeder station range.
Remedy: Specify a feeder position within the feeder station's range.
------------------------------
Code: 2100753A
Display: "Can not use cartridge type"
Used by:
Cause: An attempt was made to allocate a fixed feeder as specified by the device comment in question,
but an error occurred when the feeder was checked against the usable feeder types.
Remedy: Change the feeder type in the PST file to one that can be used by the station where the feeder is
specified as fixed.
------------------------------
第 1944 页
Code: 2100753B
Display: "There is insufficient space for a feeder in PT file"
Used by:
Cause: An attempt was made to allocate the feeder in question as specified by the PST file, but an error
occurred when the feeder width was checked against the end of the station.
Remedy: Change the PST specification number of the feeder in question.
------------------------------
Code: 2100753C
Display: "Space between feeders in PT file is insufficient"
Used by:
Cause: An attempt was made to allocate the feeder in question as specified by the PST file, but an error
occurred due to interference between feeders.
Remedy: Change the PST specification number of the feeder in question.
------------------------------
Code: 2100753D
Display: "Undefined cartridge name for device in PT file"
Used by:
Cause: The feeder type cannot be determined, because the feeder type has not been entered in the device
comment field of the PST file. The feeder type will be determined based on the Part data.
Remedy: Enter the feeder type in the relevant device comment field of the PST file.
------------------------------
Code: 21007600
Display: Illegal parameter option
Used by:
Cause: The start-up parameter is illegal.
Remedy: When doing direct start up, check and correct the input options.
------------------------------
Code: 21007601
Display: Message file read error
Used by:
Cause: Unable to read the message file.
Remedy: Re-install the software.
------------------------------
Code: 21007602
Display: CRT event link error
Used by:
Cause: Unable to link the CRT event.
Remedy: Re-boot MCS.
------------------------------
Code: 21007603
Display: Part data offset data read error
Used by:
Cause: Unable to read the Part data.
Remedy: This is a Part data format error. Check the Part data file in the Editor, and if the format is
unusual, reconstruct the file. Save the changes.
------------------------------
Code: 21007604
Display: Input program file read error
Used by:
Cause: Unable to read the input program file.
Remedy: Check that the input file can be edited. If it cannot, recreate the file.
第 1945 页
------------------------------
Code: 21007605
Display: Input program file open error
Used by:
Cause: Unable to open the input file.
Remedy: Check that the input file can be edited. If it cannot, recreate the file.
------------------------------
Code: 21007606
Display: Output program file open error
Used by:
Cause: Unable to open the output file.
Remedy: If the file already exists, check that the write protect setting is not on. If the write protect setting
is on, cancel the File Services' Write protect function.
------------------------------
Code: 21007607
Display: Output program file write error
Used by:
Cause: Unable to write to the output file.
Remedy: If the output file exists, check that the write protect setting is not on. If it is, cancel this setting
at File Services' Write protect function.
------------------------------
Code: 21007608
Display: Base program file open error
Used by:
Cause: Unable to open the file.
Remedy: Check the file.
------------------------------
Code: 21007609
Display: Base program file read error
Used by:
Cause: Unable to read the file.
Remedy: Use the Editor to check that the base program is the production program.
------------------------------
Code: 2100760A
Display: Base program file not found
Used by:
Cause: Base program file not found.
Remedy: Check the specified filename.
------------------------------
Code: 2100760B
Display: Base program file offset data read error
Used by:
Cause: Unable to read the file.
Remedy: Use the Editor to check that the base program is the production program.
------------------------------
Code: 2100760C
Display: PST file open error
Used by:
Cause: Unable to open the PST file.
Remedy: Check that the PST file can be edited. If it cannot, or if the data is incorrect, reconstruct the file.
------------------------------
第 1946 页