FUJI错误代码查询.pdf - 第551页

Make sure that the forward end and retract end sensors (X03C and X03D) turn on when the cylinder moves. ------------------------------ Code: 12054044 Display: Air Cylinder Cycle Alarm Cleaner Wiper Used by: Cause: Wiper …

sensor is broken.

Remedy: Check the operation of the clamper at the I/O board, and check the sensors.

------------------------------

Code: 1205403E

Display:

Used by:

Cause: The stroke frame unclamper cannot operate. Alternately, the stroke frame unclamper

confirmation sensor is broken.

Remedy: Check the operation of the unclamper at the I/O board, and check the sensors.

------------------------------

Code: 1205403F

Display: The tape cutter error.

Used by: CP-732E,CP-742ME,CP-742E,CP-752E

Cause: It works tape cutter, being connected with the multitude time sending by the feeder

but it doesn't work normally.

The sensor of the end of the tape cutter forward movement doesn't ON during automatic operation.

Remedy: During multitude time sending execution, confirm that the tape cutter cylinder works.

When this error occurs though the cylinder is working, adjust a sensor of the end of the forward

movement and a sensor of the end of the backward movement.

This error occurs when the automatic operation starts. In case of being, adjust a sensor of the end of the

forward movement.

------------------------------

Code: 12054040

Display:

Used by: GP551,GP6

Cause: Mask reception was not completed within the specified time.

Remedy: Check that the mask reception cylinder and sensors work correctly, and check that no objects

are interfering with the movement of the cylinder. If there are, remove the objects. Otherwise, adjust or

replace the cylinder.

------------------------------

Code: 12054041

Display: 周期异常印刷压力响应

Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP

Cause: 不能够施加所设定的印刷压力下限值以上的印刷压力。最大压和最小压都没有达到设定的印刷压力。 (GPX)

Remedy: 请确认印刷压力测定用放大器中是否正确地设定了印刷压力。可认为是气源进口压低于印刷压力下限值的设

定。请将印刷压力的设定值变更为合适的值。存在刮刀没有到达钢板的可能性。请确认刮刀的安装是否正常。（GPX)

------------------------------

Code: 12054042

Display: Pre-RQ rotation Error

Used by: CP6,CP6M,CP65,CP652C,CP642,CP643

Cause: Pre-RQ rotation could not be performed within the cycle time (Station 13).

Remedy: Check that the axis is not overloaded. Remove any objects that interfere with axis

movement.Check the cylinder's advance and retract sensors.

------------------------------

Code: 12054043

Display: "Tape feed cylinder alarm" (CP6)

Used by: CP6,CP6M,CP65,CP652C,CP642,CP643

Cause: The tape feed cylinder did not advance or retreat within the specified time.

Remedy: Perform an I/O check OUT operation to turn off cylinder stopper Y026, then make sure that the

cylinder moves forward and retracts when the cam handle is turned or when C-axis inching is performed.

第 550 页

Make sure that the forward end and retract end sensors (X03C and X03D) turn on when the cylinder

moves.

------------------------------

Code: 12054044

Display: Air Cylinder Cycle Alarm Cleaner Wiper

Used by:

Cause: Wiper operation is incorrect.

Remedy: The wiper's forward and retract sensors may be faulty. Adjust or replace the sensors.

------------------------------

Code: 12054045

Display: "Cycle alarm: squeegee separation pressure response"

Used by: GSP5,GP6

Cause: The pressure level has been reduced from printing pressure to squeegee separation pressure, but

the lower limit signal (X072:SQG PRES LO) has not turned on.

Remedy: Make sure the squeegee separation pressure has been properly set for the pressure

measurement amp (#2). Make sure that the pressure applied during printing is not lower than that

applied forsqueegee separation. Set a lower squeegee pressure value for squeegee separation than is used

when printing.

------------------------------

Code: 12054046

Display: "Tape cutter cylinder alarm"

Used by: CP652C

Cause: The tape cutter cylinder did not move up or down within the specified time.

Remedy: Perform an I/O check OUT operation to turn off cylinder stopper Y036, then make sure that the

cylinder moves up and down when the cam handle is turned or when cam axis inching is performed.When

the cylinder moves, make sure that the upper and lower limit sensors (X034 and X035) turn on If the

upper and lower limit sensors (X034 and X035) do not turn on even when the cylinder moves up and

down normally, adjust the sensors and such as needed.

------------------------------

Code: 12054047

Display: Cycle Alarm Cylinder Towel Feed UP/DOWN

Used by: GSP5,GP551,GP6,NXTP

Cause: The cleaner towel feed operation was not completed within the specified amount of time.

Remedy: Make sure that additional force is not being exerted on the towel feed operation.

------------------------------

Code: 12054048

Display: Cycle Alarm Cylinder Cleaner Shaft

Used by: GP6

Cause: There was no sensor input by the cleaner shaft advance/retract limit sensor within the specified

amount of time.

Remedy: Confirm that the cleaner shaft operation is working correctly.

------------------------------

Code: 1205404D

Display: Tool changer error

Used by: QP3OF

Cause: There is a possibility of interference between the tool changer and the holder.

Remedy: Raise the Z-axis to a position where it will not interfere with the tool changer and holder. Also,

open the [Position] ? [Toll Changer Position] screen from the [Main] screen to lower the tool changer.

------------------------------

Code: 1205404E

Display: Tool changer error

第 551 页

Used by: QP3OF

Cause: A timeout error occurred while raising/lowering the tool changer.

Remedy: Check that the tool changer is not interfering with any other part of the machine.

------------------------------

Code: 12054050

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

------------------------------

Code: 12054051

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

------------------------------

Code: 12054052

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

------------------------------

Code: 12054053

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

------------------------------

Code: 12054054

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

------------------------------

Code: 12054055

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

------------------------------

Code: 12054056

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

------------------------------

Code: 12054057

Display: Abolished

Used by: QP132

Cause: Abolished

Remedy: Abolished

第 552 页