FUJI错误代码查询.pdf - 第544页

Used by: IP1,IP2,IP3 Cause: An alarm has occurred in a stick feeder or tape feeder cylinder system. Remedy: Adjust the stick or tape feeder cylinder so that it is capable of moving forward and retracting. ---------------…

100%1 / 5282
Cause: The machine attempted to move the pallet in the IN station, the stopper has not been turned off.
Remedy: Make sure that both the stopper is functioning normally. Check the stopper OFF limit sensor.
------------------------------
Code: 12054004
Display: "Pallet clamp error: DF IN stn"
Used by: CP5
Cause: The DF-axis has failed to clamp a pallet at the pallet IN station.
Remedy: Make sure the DF-axis pallet clamp is functioning normally. Check the upper limit and clamp
check sensors.
------------------------------
Code: 12054005
Display: "Pallet clamp error: DR IN stn"
Used by: CP5
Cause: The DR-axis failed to clamp a pallet at the pallet IN station.
Remedy: Make sure the DR-axis pallet clamp is functioning normally. Check the upper limit and clamp
check sensors.
------------------------------
Code: 12054006
Display: CHECK CLUTCH
Used by: CP3,CP4-1,CP4-2
Cause: There was a clutch movement alarm (CP3).
Remedy: Check the clutch.
------------------------------
Code: 12054007
Display: "Cycle alarm: carrier" (IP)
Used by: IP1
Cause: A problem has occurred in the tray component carrier cylinder system.
Remedy: Adjust the carrier cylinder so that it is capable of moving forward and retracting. Confirm that
the carrier's forward end and retract end sensors are functioning normally.
------------------------------
Code: 12054008
Display: "Cycle alarm: sub nozzle" (IP)
Used by: IP1
Cause: A problem has occurred in the subrobot nozzle cylinder system.
Remedy: Adjust the subrobot nozzle cylinder so that it is capable of moving up and down. Confirm that
the subrobot nozzle's upper and lower limit sensors are functioning normally.
------------------------------
Code: 12054009
Display: Cycle Alarm Tray Remover
Used by: IP1
Cause: There was a tray removal cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the tray removal cylinder.
------------------------------
Code: 1205400A
Display: Cycle Alarm Error conveyor
Used by: IP1,IP2,IP3
Cause: There was a rejected parts conveyor alarm.
Remedy: Adjust the operating ability of the rejected parts conveyor motor.
------------------------------
Code: 1205400B
Display: "Cycle alarm: feeder" (IP,IP2)
第 543 页
Used by: IP1,IP2,IP3
Cause: An alarm has occurred in a stick feeder or tape feeder cylinder system.
Remedy: Adjust the stick or tape feeder cylinder so that it is capable of moving forward and retracting.
------------------------------
Code: 1205400C
Display: PCM OUT Cylinder Time Out
Used by: CP5
Cause: The palette was not successfully unloaded from the out station to the down lifter.
Remedy: Check the PCM's out cylinder as well as the out cylinder's extended position.
------------------------------
Code: 12054010
Display: Cycle Alarm NOZZLE SHUTTER(IP)
Shutter(IP2)
Nozzle shutter error!(NP2,QP3)
Used by: IP1,IP2,NP2,QP3
Cause: There was a nozzle shutter cylinder alarm.
The nozzle shutter failed to open within the specified time (time-out error).(NP2,QP3)
Remedy: Adjust the advanced and retracted positions of the nozzle shutter cylinder.
Check the action of the nozzle shutter.(NP2,QP3)
------------------------------
Code: 12054012
Display: Cycle Alarm NOZZLE SHIFT
Used by: IP1,IP2
Cause: There was a nozzle shift cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the nozzle shift cylinder.
------------------------------
Code: 12054013
Display: Cycle Alarm Holder1
Used by: IP2
Cause: There was a holder 1 cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the nozzle shutter cylinder.
------------------------------
Code: 12054014
Display: Cycle Alarm Holder2
Used by: IP2
Cause: There was a holder 2 cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the holder 2 cylinder.
------------------------------
Code: 12054015
Display: Cycle Alarm Holder3
Used by: IP2
Cause: There was a holder 3 cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the holder 3 cylinder.
------------------------------
Code: 12054016
Display: Cycle Alarm Holder4
Used by: IP2
Cause: There was a holder 4 cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the holder 4 cylinder.
------------------------------
Code: 12054017
第 544 页
Display: Cycle Alarm Chuck
Used by: IP1,IP2
Cause: There was a nozzle chuck cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the nozzle chuck cylinder.
------------------------------
Code: 12054018
Display: Cycle Alarm H2
Used by: IP2
Cause: A time up error has occured for the cylinder which moves the second holder to its ready position.
Remedy: Check the cylinder.
------------------------------
Code: 12054019
Display: Cycle Alarm H3
Used by: IP2
Cause: A time up error has occured for the cylinder which moves the third holder to its ready position.
Remedy: Check the cylinder.
------------------------------
Code: 1205401A
Display: Cycle Alarm ESC 2
Used by: IP2
Cause: A time up error has occured for the cylinder which moves the first holder to its retracted position.
Remedy: Check the cylinder.
------------------------------
Code: 1205401B
Display: Cycle Alarm ESC 3
Used by: IP2
Cause: A time up error has occured for the cylinder which moves the second holder to its retracted
position.
Remedy: Check the cylinder.
------------------------------
Code: 1205401D
Display: Cycle Alarm MFU1 Notch
Used by: IP2
Cause: The MFU1 fixed notch did not go in within the preset time.
Remedy: Check that the MFU1 fixed notch cylinder is operating properly.
------------------------------
Code: 1205401E
Display: Cycle Alarm MFU2 Notch
Used by: IP2
Cause: The MFU2 fixed notch did not go in within the preset time.
Remedy: Check that the MFU2 fixed notch cylinder is operating properly.
------------------------------
Code: 1205401F
Display: Cycle Alarm FRAME
Used by: GSP2,GSP3,GP2,GP3
Cause: The frame did not operate properly within the preset time.
Remedy: Check that there is no object interfering with the movement of the frame.
------------------------------
Code: 12054020
Display: 周期异常 电路板压板 L or R (GSP)
周期异常 汽缸 电路板压板(GP)
第 545 页