FUJI错误代码查询.pdf - 第462页

Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected, notify Fuji. ------------------------------ Code: 120377?? Display: SECS1 LINK creation error Used by: CP3,CP5,GP551,…

100%1 / 5282
or if this problem occurs often, contact Fuji.
------------------------------
Code: 120372E?
Display: ETHERNET creation error
Used by: CP3
Cause: In conjunction with the internal processing of the machine software, an attempt was made to
create an Ethernet driver using the _create_ether() system call of the Fuji operation system. However,
creation of the Ethernet driver was not successful because of insufficient memory. The last digit in the
error code indicates the number of the unit for which creation was attempted (?: indicatesthe unit
number).
Remedy: Reboot the machine using the reset-start procedure. If operation works properly after the reset-
start then wait in this status for several minutes. Consult Fuji if nothing changes even after a reset-start
is carried out or if the same type of symptoms occur frequently.
------------------------------
Code: 120373??
Display: MT LINK creation error
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GP551,GP6,QP242,QP201,QP202,QP203
Cause: An error occurred when an attempt was made to generate a unit control block and a link for the
carriage return terminate communication module. This error occurred when Fuji OS system call_mt_link()
was used. The last two numbers in the error code indicate the unit in which the error occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 120374??
Display: IP LINK creation error
Used by: CP3,CP5,QP242,QP201,QP202,QP203
Cause: An error occurred due to a lack of memory and duplicated settings when an attempt was made to
generate the unit control block (UCB) in the IP module. This error occurred when Fuji OS system
call_ip_link() was used. The last two numbers in the error code indicate the unit in which the error
occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 120375??
Display: UDP LINK creation error
Used by: CP3,CP5
Cause: An error occurred due to a lack of memory and duplicated settings when an attempt was made to
generate the unit control block (UCB) in the UDP module. This error occurred when Fuji OS system
call_udp_link() was used. The last two numbers in the error code indicate the unit in which the error
occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 120376??
Display: UDP BIND creation error
Used by: CP3,CP5
Cause: An error occurred due to a lack of memory and duplicated settings when an attempt was made to
branch and generate the unit for the UDP module. This error occurred when Fuji OS system
call_udp_bind() was used. The last two numbers in the error code indicate the unit in which the error
occurred.
第 461 页
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 120377??
Display: SECS1 LINK creation error
Used by: CP3,CP5,GP551,GP6,QP242,QP201,QP202,QP203
Cause: An error occurred due to a lack of memory and duplicated settings when an attempt was made to
generate the unit control block (UCB) for the SECS1 module. This error occurred when Fuji OS system
call_secs1_link() was used. The last two numbers in the error code indicate the unit in which the error
occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 120378??
Display: SECS2 LINK creation error
Used by: CP3,CP5,QP242,QP201,QP202,QP203
Cause: An error occurred due to a lack of memory and duplicated settings when an attempt was made to
generate the unit control block (UCB) for the SECSII module. This error occurred when Fuji OS system
call_secs2_link() was used. The last two numbers in the error code indicate the unit in which the error
occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 120379??
Display: HT LINK creation error
Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GP551
Cause: An error occurred due to a lack of memory and duplicated settings when an attempt was made to
generate the unit control block (UCB) for the handy terminal. This error occurred when Fuji OS system
call_ht_link() was used. The last two numbers in the error code indicate the unit in which the error
occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037A0?
Display: INTL SRV creation error
Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GP551,GP6
Cause: An error occurred due to a lack of memory when an attempt was made to generate the driver for
the intelligent servo board. This error occurred when Fuji OS system call_create_intl_srv() was used. The
last number in the error code indicates the board in which the error occurred. 0 indicates the first board.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037A1?
Display: INTL SRV creation error
Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GP551,GP6
Cause: An attempt was made to generate the driver for the intelligent servo board but the board was not
in the "Ready" state. This error occurred when Fuji OS system call_create_intl_srv() was used. The last
number in the error code indicates the board in which the error occurred. 0 indicates the first board.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
第 462 页
Code: 12037A2?
Display: INTL SRV initialize error
Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GP551,GP6
Cause: Initialization of the intelligent servo board is not complete. This error occurred when Fuji OS
system call_intl_init_chk() was used. The last number in the error code indicates the board number in
which the error occurred. 0 indicates the first board.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037A3?
Display: PI SRV creation error
Used by:
Cause: An error occurred when an attempt was made to generate the driver which performs servo driver
PI control. This error occurred when Fuji OS system call_create_pi_srv() was used. The last number in
the error code indicates the axis in which the error occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037A4?
Display: TBA SRV creation error
Used by: CP3
Cause: An error occurred when an attempt was made to generate the driver which controls the
acceleration speed of the servo driver. This error occurred when Fuji OS system call_create_tba_srv() was
used. The last number in the error code indicates the axis in which the error occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037A5?
Display: OLD SRV creation error
Used by: CP4-1,CP4-2,CP4-3,GL541,GP551,GP6
Cause: An error occurred during an attempt to generate the driver which controls the target value. This
error occurred when Fuji OS system call_create_old_srv() was used. The last number in the error code
indicates the axis in which the error occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037A6?
Display: CNT SRV creation error
Used by:
Cause: An error occurred when an attempt was made to generate the counter driver for the system which
uses 8253 (PIT). This error occurred when Fuji OS system call_create_cnt_srv() was used. The last
number in the error code indicates the axis in which the error occurred.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037A7?
Display: Reduce data creation error
Used by: CP3,CP4-1,CP4-2,CP4-3,GL541,GP551,GP6
Cause: An error occurred due to a lack of memory when an attempt was made to generate the
deceleration function data used by the servo. This error occurred when Fuji OS system
call_create_reduce() was used. The last number in the error code indicates the axis in which the error
第 463 页