FUJI错误代码查询.pdf - 第2109页
Code: 2100F050 Display: Sequence(Z) count over. Used by: Cause: An error occurred when performing a snap-off sequence check. Remedy: Edit the file to ensure that the number of board snap-off sequences is less than 10. --…
------------------------------
Code: 2100F048
Display: Nozzle_assignment_table file load error
Used by:
Cause: The nozzle assignment table could not be loaded.
Remedy: Check the nozzle assignment table. Input the same nozzle assignment table name's machine
type under the program's "Nozzle_assignment_table" heading.
------------------------------
Code: 2100F049
Display: Mount or Glue or Dummyg sequence is out of order
Used by:
Cause: There are sequences after the cleaning sequences.
Remedy: Move the cleaning sequence to the end of the program. The cleaning sequence must be the final
sequence.
------------------------------
Code: 2100F04A
Display: NAT check error
Used by:
Cause: NAT check error.
Remedy: Refer to the NAT error that occurred at the same time (2100FE**).
------------------------------
Code: 2100F04B
Display: Could not fork ntchk task
Used by:
Cause: The NAT checker (NTCHK) could not be started.
Remedy: Reboot MCS or re-install the system.
------------------------------
Code: 2100F04C
Display: Default value is used if no data is entered
Used by:
Cause: The program structure and descriptor structure are different.
Remedy: This is a warning. Save and correct the file using the editor.
------------------------------
Code: 2100F04D
Display: Can't open environment file.
Used by:
Cause: An error occurred when an attempt was made to open the environment setting file.
Remedy: Install the environment setting file from the MCS/2 system disk to /h0/MCS2/.SYS.
------------------------------
Code: 2100F04E
Display: Can't read environment file.
Used by:
Cause: An error occurred when the environment setting file was read.
Remedy: Install the environment setting file from the MCS/2 system disk to /h0/MCS2/.SYS.
------------------------------
Code: 2100F04F
Display: Sequence(Z) : XY data over range.
Used by:
Cause: An error occurred when performing a snap-off sequence check.
Remedy: Edit the file to ensure that the snap-off sequence XY coordinates are within range.
------------------------------
第 2108 页
Code: 2100F050
Display: Sequence(Z) count over.
Used by:
Cause: An error occurred when performing a snap-off sequence check.
Remedy: Edit the file to ensure that the number of board snap-off sequences is less than 10.
------------------------------
Code: 2100F051
Display: Sequence(Z) : X data is out of order.
Used by:
Cause: An error occurred when performing a snap-off sequence check.
Remedy: Edit the relevant file using the editor to ensure that the X coordinates of the snap-off sequences
are ranked in ascending order.
------------------------------
Code: 2100FA00
Display: can't read strings file
Used by:
Cause: The prop_str.E file cannot be loaded into the memory.
Remedy: Re-boot MCS. If the error recurs, re-install the system.
------------------------------
Code: 2100FA01
Display: Syntax error - Illegal '+' option
Used by:
Cause: The + option was not specified correctly at start-up.
Remedy: If this error occurred during a direct command, correct the input command.
------------------------------
Code: 2100FA02
Display: Syntax error - illegal '-' option
Used by:
Cause: The '-' option was not specified correctly at start-up.
Remedy: Correct the input command if this error occurred due to a direct command.
------------------------------
Code: 2100FA03
Display: Syntax error - check file not found
Used by:
Cause: The specified object file does not exist.
Remedy: Correct the name of the specified object file.
------------------------------
Code: 2100FA04
Display: not found - check file on disk
Used by:
Cause: The specified file does not exist.
Remedy: Correct the filename.
------------------------------
Code: 2100FA05
Display: can't create output file
Used by:
Cause: Output file could not be created.
Remedy: Check the RAM for previously created files and for remaining memory. Re-boot MCS.
------------------------------
Code: 2100FA06
Display: can't create print file
第 2109 页
Used by:
Cause: The print file could not be created.
Remedy: Check the RAM for previously created files and for remaining memory. Re-boot MCS.
------------------------------
Code: 2100FA07
Display: change console path error
Used by:
Cause: The terminal path could not be selected during start-up.
Remedy: Check the RAM for previously created files and for remaining memory. Re-boot MCS.
------------------------------
Code: 2100FA08
Display: CRT event link error
Used by:
Cause: The terminal event could not be linked.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100FA09
Display: can't load proper file on memory
Used by:
Cause: The specified file cannot be loaded into memory.
Remedy: Reboot MCS or re-install the system.
------------------------------
Code: 2100FA0A
Display: can't load file descriptor on memory
Used by:
Cause: The file descriptor could not be loaded into memory.
Remedy: Re-boot MCS. If the error recurs, re-install the system.
------------------------------
Code: 2100FA0B
Display: this file is not proper
Used by:
Cause: The specified file is not a Proper data file.
Remedy: Specify the correct file.
------------------------------
Code: 2100FA0C
Display: can't open Lp pipe
Used by:
Cause: The Lp pipe could not be opened.
Remedy: Re-boot MCS.
------------------------------
Code: 2100FA0D
Display: check flag rewrite error
Used by:
Cause: The check flag could not be re-written.
Remedy: Check that the file overwrite protector is not set to prevent overwriting.
------------------------------
Code: 2100FA0E
Display: Proper data NO. %d over range
Used by:
Cause: The **** Proper data item is out of range.
Remedy: Reset the item in question so that it is no longer out of range.
第 2110 页