FUJI错误代码查询.pdf - 第686页
Code: 120685AB Display: TY-axis: Communication error! Used by: QP3,NP2 Cause: Remedy: Check that the MECHATROLINK communications cable between the MTU controller and servo amplifier is connected correctly. --------------…
Code: 120685A3
Display: TY-axis: Encoder parameter error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 120685A4
Display: TY-axis: Encoder echo-back error.
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 120685A5
Display: TY-axis: Multiturn limit disagreement.
Used by: QP3,NP2
Cause:
Remedy: Check that the correct value is entered for the Pn205 servo parameter.
------------------------------
Code: 120685A6
Display: TY-axis: Position deviation overflow error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 120685A7
Display: TY-axis: No option error!
Used by: QP3,NP2
Cause:
Remedy: Check that the MECHATROLINK interface unit is correctly attached to the servo amplifier.If
correct installation does not rectify the problem, replace the MECHATROLINK interface unit.
------------------------------
Code: 120685A8
Display: TY-axis: Option time-out error!
Used by: QP3,NP2
Cause:
Remedy: Check that the MECHATROLINK interface unit is correctly attached to the servo amplifier.If
correct installation does not rectify the problem, replace the MECHATROLINK interface unit.
------------------------------
Code: 120685A9
Display: TY-axis: Option WDC error!
Used by: QP3,NP2
Cause:
Remedy: Check that the MECHATROLINK interface unit is correctly attached to the servo amplifier.If
correct installation does not rectify the problem, replace the MECHATROLINK interface unit.
------------------------------
Code: 120685AA
Display: TY-axis: WDT error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
第 685 页
Code: 120685AB
Display: TY-axis: Communication error!
Used by: QP3,NP2
Cause:
Remedy: Check that the MECHATROLINK communications cable between the MTU controller and servo
amplifier is connected correctly.
------------------------------
Code: 120685AC
Display: TY-axis: Servo response error!
Used by: QP3,NP2
Cause:
Remedy: Replace the servo amplifier.
------------------------------
Code: 120685AD
Display: TY-axis: Servo back initial access error!
Used by: QP3,NP2
Cause:
Remedy: Replace the servo amplifier.
------------------------------
Code: 120685AE
Display: TY-axis: Servo back WDC error!
Used by: QP3,NP2
Cause:
Remedy: Replace the servo amplifier.
------------------------------
Code: 120685AF
Display: TY-axis: Command uncompleted.
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 120685B0
Display: TY-axis: Power line open phase.
Used by: QP3,NP2
Cause:
Remedy: Check the servo amplifier power cable connection.
------------------------------
Code: 12068600
Display: TZ-axis: Cycle error!
Used by: QP3,NP2
Cause:
Remedy: TZ-axis: Check the servo motor, servo amp and wiring.
------------------------------
Code: 12068601
Display: TY-axis: Cycle error!
Used by: QP3,NP2
Cause:
Remedy: TY-axis: Check the servo motor, servo amp and wiring.
------------------------------
Code: 12068610
Display: Lifter ascent error!
第 686 页
Used by: QP3,NP2
Cause:
Remedy: Check if the lifer upper limit sensor is on, or if the remover lower limit sensor is off. Also check if
there is a delay in lifter ascent.
------------------------------
Code: 12068611
Display: Remover descent error!
Used by: QP3,NP2
Cause:
Remedy: Check if the lifter upper limit sensor is off, or if the lower limit sensor is on. Also check if there is
a delay in lifter descent.
------------------------------
Code: 12068612
Display: Remover chucking error!
Used by: QP3,NP2
Cause:
Remedy: Check if the remover's chucking sensor is on. Also check if there is a delay in the chucking
motion.
------------------------------
Code: 12068613
Display: Remover release cycle error!
Used by: QP3,NP2
Cause:
Remedy: Check if the remover's chucking sensor is off. Also check if there is a delay in the remover's
release motion.
------------------------------
Code: 12068614
Display: Remover hose ascent cycle error.
Used by: QP3,NP2
Cause:
Remedy: The remover hose was raised, but the upper limit sensor did not turn off within the required 3
second time period.
------------------------------
Code: 12068615
Display: Remover hose descent cycle error.
Used by: QP3,NP2
Cause:
Remedy: The remover hose was lowered, but the lower limit sensor did not turn off within the required 3
second time period.
------------------------------
Code: 12068616
Display: Clamper cylinder cycle error.
Used by: QP3,NP2
Cause: Even though the clamper cylinder operates, the status of the clamp cylinder open limit sensor
does not change.
Remedy: Check the operation of the clamper cylinder, or check that the clamp cylinder open limit sensor
triggers correctly.
------------------------------
Code: 12068800
Display: TZ-axis interlock error (TY-axis intermediate position).
Used by: QP3,NP2
第 687 页