FUJI错误代码查询.pdf - 第589页

Code: 12056120 Display: "Move squeegee head to escape position." Used by: GP551 Cause: The squeegee head is not at the lock position. Remedy: Move the squeegee head to the lock position. -----------------------…

------------------------------

Code: 1205611A

Display: "Interlock Cleaner F Holder Up"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the front squeegee holder is down.

Remedy: Raise the front squeegee (set Y01D:F SQG HLDR UP to 0). If necessary, make sure that the front

squeegee holder upper limit check sensor (X070:F SQG HLDR UP) is functioning normally.

------------------------------

Code: 1205611B

Display: "Interlock Cleaner R Holder Up"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the rear squeegee holder is down.

Remedy: Raise the rear squeegee (set Y02F:R SQG HLDR UP to 0). If necessary, make sure that the rear

squeegee holder upper limit check sensor (X078:R SQG HLDR UP) is functioning normally.

------------------------------

Code: 1205611C

Display: "Interlock Conveyor Width Clutch"

Used by: GP6

Cause: The conveyor width clutch was turned on during automatic operation. This error occurs if the

conveyor width clutch turns on and interferes with the Z-axis during automatic operation.

Remedy: Use [UNLOCK] on command page 300(5)(1) to turn the conveyor width clutch off.If necessary,

make sure that the left and right conveyor width notch limit check sensors (X035:W_CLUTCH1_OFF

andX037:W_CLUTCH2_OFF) are functioning normally.

------------------------------

Code: 1205611D

Display: "Interlock Cleaner Connected"

Used by: GP6

Cause: The cleaner is interfering with the S-axis. This error occurs if the cleaner is connected to the S-

axis when the S-axis is moved to the printing position during automatic operation.

Remedy: Use [HEAD REMOVAL] on command page 553-2(3) to disconnect the cleaner from the S-axis. If

necessary, make sure that the lower cleaner connection check sensor, the cleaner connection

positionproximity check sensor, and the lower cleaner origin position check sensors (X05D:LW CLR CPL

CHK, X03E:CLNR NEAR CHK, and X05C:CLNR ZERO POS) are functioning normally.

------------------------------

Code: 1205611E

Display: 请待机Ｚ轴

[Z escape]

Used by: GP6,GPX

Cause: Ｚ轴与清洁器(移位)发生干涉。在清洁动作的清洁器移位前进时Ｚ轴不在待机位置的情况下发生。存在清洁

器和主工作台发生了干涉的可能性。 (GPX)

Remedy: 请将Ｚ轴移动到Ｚ轴待机位置(X03C:Z ESC POS CHK 为O的位置)。或者，请确认Ｚ轴相机干涉防止联锁

传感器(X03C:Z ESC POS CHK)。 1.虽然稍重但是请用手将清洁器移动至退避位置。

2.发生了干涉时，请与本公司的Support联系。（GPX)

------------------------------

Code: 1205611F

Display: "Move upper cleaner to escape position."

Used by: GP551

Cause: The upper cleaner is not at the escape position.

Remedy: Move the upper cleaner to the escape position.

------------------------------

第 588 页

Code: 12056120

Display: "Move squeegee head to escape position."

Used by: GP551

Cause: The squeegee head is not at the lock position.

Remedy: Move the squeegee head to the lock position.

------------------------------

Code: 12056121

Display: Move camera to lower cleaner coupling position

Used by: GP551

Cause: The lower cleaner coupler is not in position.

Remedy: Move the camera or the lower cleaner coupler into position.

------------------------------

Code: 12056122

Display: Move lower cleaner to retract position

Used by: GP551

Cause: The lower cleaner is not at its retract position.

Remedy: Move the lower cleaner to its retract position.

------------------------------

Code: 12056123

Display: 联锁（Ｚ｜Ｙ）轴　电路板通过确认

[Interlock （Ｚ｜Ｙ）axis ]

Used by: GP551,GPX,NXTP

Cause: 在移动所显示的轴时，IN-MAIN搬运轨道的电路板换乘确认传感器或MAIN-OUT搬运轨道的电路板换乘确认

传感器因为确认了电路板，所以不能够移动平台。

Remedy: 请从搬运轨道上除去电路板。或者，请确认平台移动许可确认传感器的ON/OFF动作。

------------------------------

Code: 12056124

Display: "Interlock CX axis Z axis"

Used by: GP551

Cause: The Z-axis may interfere with the CX-axis. This error occurs if the CX-axis is moved while the Z-

axis is not at the escape position.

Remedy: Move the Z-axis to the escape position. If necessary, make sure that the Z-axis escape position

check sensor is functioning normally.

------------------------------

Code: 12056125

Display: Interlock Camera/Non-retracted Upper|Lower Cleaner

Used by: GP551

Cause: The cleaner has not been stowed. This error occurs during the coupling of the camera axis and

cleaner, if an attempt is made to move the camera axis when the cleaner is not in the stored position.

Remedy: Move the cleaner to the stored position. Alternatively, check the cleaner storage sensor.

------------------------------

Code: 12056126

Display: "Interlock S axis"

Used by: GP551

Cause: The S-axis may interfere with the upper cleaner. This error occurs if the cleaner drive axis is

moved while the S-axis is not at the escape position.

Remedy: Move the S-axis to the escape position. If necessary, make sure that the S-axis escape position

check sensor is functioning normally.

------------------------------

Code: 12056127

第 589 页

Display: Interlock Top cleaner Supply Solder

Used by: GP551

Cause: The solder supply unit (SSD-axis) and the upper cleaner may collide. This error occurs when the

solder supply unit (SSD-axis) is not at the retract position and the cleaner axis is moving.

Remedy: Move the solder supply unit (SSD-axis) to the retract position. Alternatively, check the on/off

status of the SSD-axis' retract position sensor.

------------------------------

Code: 12056128

Display: 联锁相机　下清洁器连结

[Interlock Camera　]

Used by: GP551,GPX

Cause: ＣＸ轴与下清洁器连结着。在ＣＹ轴移动时ＣＸ轴与下清洁器处于连结状态的情况下发生。存在清洁器和相

机机械手发生了干涉的可能性。 (GPX)

Remedy: 请解除ＣＸ轴与下清洁器的连结。或者，请确认下清洁器连结、下清洁器／相机轴接近的各确认传感器的

ON/OFF动作。 1.请用手将清洁器移动到退避位置。

2.发生了干涉时，请与本公司的Support联系。（GPX)

------------------------------

Code: 12056129

Display: Interlock S axis Solder Pusher

Used by: GP551

Cause: This error occurs when the S-axis moves while the solder pusher is down.

Remedy: Raise the solder pusher. Alternatively, check the on/off status of the solder pusher's up

position/down position sensors.

------------------------------

Code: 1205612A

Display: Interlock S axis SQG Open/Close

Used by: GP551

Cause: This error occurs when the S-axis moves while the squeegee head is opened.

Remedy: Close the squeegee head. Alternatively, check the on/off status of the squeegee head's

open/closed sensors.

------------------------------

Code: 1205612B

Display: "Interlock S axis"

Used by: GP551

Cause: This error occurs if the S-axis is moved while the squeegee head is not stored.

Remedy: Store the squeegee head. If necessary, make sure that the squeegee head storage check sensor

is functioning normally.

------------------------------

Code: 1205612C

Display: Interlock Y axis Z axis

Used by: GP551

Cause: This error occurs if the Y-axis moves when the Z-axis is not at the retract position.In order to

detect an abnormal board width, the Y-axis can only move when the Z-axis is at the retract position.

Remedy: Move the Z-axis to the retract position. Alternatively, check the on/off status of the Z-axis'

retract position sensor.

------------------------------

Code: 1205612D

Display: Interlock Y axis Main Stopper

Used by: GP551,NXTP

Cause: This error occurs when the Y-axis moves while the main stopper is down.

第 590 页