FUJI错误代码查询.pdf - 第2097页
Code: 2100EDD1 Display: Used by: Cause: The Part Sort table was not found. Remedy: Check that the file exists. ------------------------------ Code: 2100EDD2 Display: Used by: Cause: The Part Data file (H0/DATA/part.data)…
Remedy: Correct the file name.
------------------------------
Code: 2100EDB0
Display:
Used by:
Cause: The MCS/2 Part Data directory could not be opened.
Remedy: Check the directory.
------------------------------
Code: 2100EDB1
Display:
Used by:
Cause: The temporary file to display Part data could not be created.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDB2
Display:
Used by:
Cause: The temporary file to display Part data could not be created.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDB3
Display:
Used by:
Cause: Data could not be written to the temporary file to display Part data.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDB4
Display:
Used by:
Cause: A module does not exist.
Remedy: Re-install the translator software.
------------------------------
Code: 2100EDB5
Display:
Used by:
Cause: The system command (Dir) could not be used.
Remedy: Re-install OS-9.
------------------------------
Code: 2100EDB6
Display:
Used by:
Cause: The temporary file to display the Part Data could not be opened.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDD0
Display:
Used by:
Cause: The start-up parameters are incorrect.
Remedy: Correct the input command if this error occurred due to a direct command. Contact Fuji if the
error did not occur due to a direct command.
------------------------------
第 2096 页
Code: 2100EDD1
Display:
Used by:
Cause: The Part Sort table was not found.
Remedy: Check that the file exists.
------------------------------
Code: 2100EDD2
Display:
Used by:
Cause: The Part Data file (H0/DATA/part.data) does not exist.
Remedy: The Translator cannot run because the Part data file does not exist.
------------------------------
Code: 2100EDD3
Display:
Used by:
Cause: The Part Sort table could not be opened.
Remedy: Check the file.
------------------------------
Code: 2100EDD4
Display:
Used by:
Cause: The Part Data could not be opened.
Remedy: Check that the file exists.
------------------------------
Code: 2100EDD5
Display:
Used by:
Cause: A Part data file with the same name already exists in MCS/1.
Remedy: Set the overwrite protect to YES to replace the contents of the existing file, or specify a new file
name.
------------------------------
Code: 2100EDD6
Display:
Used by:
Cause: The data could not be translated into MCS/1 Part data.
Remedy: Re-execute the function.
------------------------------
Code: 2100EDD7
Display:
Used by:
Cause: The MCS/2 Part data input file does not exist.
Remedy: The Translator cannot run as the Part data file does not exist.
------------------------------
Code: 2100EDD8
Display:
Used by:
Cause: The MCS/2 Part data input file could not be read.
Remedy: Make sure that the contents of the file are correct.
------------------------------
Code: 2100EDD9
Display:
第 2097 页
Used by:
Cause: Data could not be written to MCS/1 output file.
Remedy: Check the condition of the disk.
------------------------------
Code: 2100EDDA
Display:
Used by:
Cause: The Part Sort table could not be read.
Remedy: Check that the file exists.
------------------------------
Code: 2100EDDB
Display:
Used by:
Cause: The MCS/2 Part data input file could not be opened.
Remedy: Check the file.
------------------------------
Code: 2100EDDC
Display:
Used by:
Cause: The system command (fixmod) could not be used.
Remedy: Re-install OS-9.
------------------------------
Code: 2100EDDD
Display:
Used by:
Cause: The MCS/1 Part data file could not be copied.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDDE
Display:
Used by:
Cause: The floppy disk drive cannot operate.
Remedy: Make sure that the floppy disk drive lock lever is fully closed.
------------------------------
Code: 2100EDDF
Display:
Used by:
Cause: The amount of Part data exceeds the capacity of the MCS/1 Part data file (500 items). No more
data items can be translated.
Remedy: Remove any unnecessary data items from the Part data file and run the translator again.
------------------------------
Code: 2100EDE0
Display:
Used by:
Cause: A module does not exist.
Remedy: Re-install the software.
------------------------------
Code: 2100F000
Display: can't read strings file
Used by:
Cause: The string file (chk_str.E) could not be loaded to memory.
第 2098 页