FUJI错误代码查询.pdf - 第2142页

Display: A feeder included in fixed feeder processing cannot be loaded on the stage because it is too close to the feeder to the left. Used by: Cause: In the program's feeder setup, a feeder wide enough to interfere…

Cause: The Part data, referred to by a sequence slot that contains no skipped board/feeder/sequence

setting, does not exist.

Remedy: The program file is incorrect. Check and correct the file contents.

------------------------------

Code: 23040008

Display: No feeder exists in the slot referenced by this skipped sequence (for skipped sequences included

in optimization).

Used by:

Cause: A feeder does not exist in a sequence slot that contains board/feeder/sequence skip settings.

Remedy: The program file is incorrect. Check and correct the file contents.

------------------------------

Code: 2304000A

Display: Part data referred to by the skip sequence does not exist. This error can be avoided by selecting

[Lines to Skip are Removed] when you optimize.

Used by:

Cause: The part data referred to by a sequence slot containing board/feeder/sequence skip settings does

not exist.

Remedy: The program file is incorrect. Check and correct the file contents.

------------------------------

Code: 2304000D

Display: The Alt. Feeder does not exist. Do you want to set 0 for alternate feeder?

Used by:

Cause: A feeder is not set in the alternate feeder specified for the displayed stage-slot.

Remedy: The Feeder Setup information in the program file is incorrect. Check the settings.

------------------------------

Code: 2304000E

Display: There are too many feeders allocated to one stage.

Used by:

Cause: When automatic feeder arrangement was selected at the Optimize Condition settings screen, the

number of feeders allocated to the stage exceeded the maximum feeder slots.

Remedy: Firstly, try changing the [Use feeder type] settings. If unsuccessful, perform optimization using

the [Alt. Feeders are Removed] setting. If still unsuccessful, reduce the part varieties used in the program.

------------------------------

Code: 23040010

Display: Part data referred to by the unused feeders in the [Fix Feeder Slots] does not exist. (Even for

unused feeder(s) without part data, it can't be determined whether the feeder is set at the machine.) This

error can be avoided by selecting [Automatic Most Suitable Feeder Arrangement] when you optimize.

Used by:

Cause: There is no part data displayed in the Feeder Setup.

Remedy: The program file data is incorrect. Check the contents.

------------------------------

Code: 23040012

Display: The slot number does not exist at the machine. This error can be avoided by selecting [Automatic

Most Suitable Feeder Arrangement] when you optimize.

Used by:

Cause: The specified stage - slot number does not exist.

Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTSTN) and slot number

(PROGRAM/DEVICE+/GUTSLTN), or alternatively use the [Automatic Most Suitable Feeder Arrangement]

setting for optimization.

------------------------------

Code: 23040015

第 2141 页

Display: A feeder included in fixed feeder processing cannot be loaded on the stage because it is too close

to the feeder to the left.

Used by:

Cause: In the program's feeder setup, a feeder wide enough to interfere with the adjacent feeder on the

left side.

Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTSTN) and slot number

(PROGRAM/DEVICE+/GUTSLTN), or alternatively, use the [Automatic Most Suitable Feeder Arrangement]

setting for optimization.

------------------------------

Code: 2304001A

Display: Are you finished?

Used by:

Cause: The confirmation dialog displays at each time of completion.

Remedy: Select [Yes] to finish. Select [No] to continue.

------------------------------

Code: 2304001B

Display: The optimized program has not been saved yet. Will you save it?

Used by:

Cause: Attempting to open the program file, or optimization process has completed, but the optimized

program has not been saved to the file.

Remedy: Select [Yes] to display the dialog for saving the file with a new name.

When attempting to open the program file, select [No] to abandon the optimized program, and display the

dialog for selecting a new program file to be optimized.

When optimization process has completed, select [No] to exit without saving the optimized program.

------------------------------

Code: 2304001C

Display: No nozzle is registered.

Used by:

Cause: No valid nozzle match could be made between the Nozzle Config. file's NCFTYPE and the Nozzle

Spec. file's NSPNAME.

Remedy: There is a problem with either or both files. Normally, the Nozzle Config. and Nozzle Spec. files

in the MCS-X default directory are read automatically. Check that both files contain correct data. When

starting up the optimizer, in cases where prompted to specify a file because the default file cannot be

found, check the file contents and correct if necessary.

------------------------------

Code: 2304001D

Display: Nozzle Configuration File "Fujinzl.cfg" cannot be found. Specify a file?

Used by:

Cause: An attempt was made to read the Nozzle Config. File in the MCS-X default directory, but the file

could not be found. A file needs to be specified to continue.

Remedy: Select [Yes] to display the dialog for specifying a file. Select [Abort] to quit the optimizer.

------------------------------

Code: 2304001E

Display: The contents of Nozzle Configuration File are empty.

Used by:

Cause: The Nozzle Config. file is empty.

Remedy: There is a problem with the Nozzle Config. file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

第 2142 页

Code: 2304001F

Display: Contents are not Nozzle Configuration File.

Used by:

Cause: The field "UNIT", "NZLCONF" does not exist.

Remedy: There is a problem with the Nozzle Config. file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

Code: 23040020

Display: Cannot read the file.

Used by:

Cause: An error occurred while reading the Nozzle Config. file.

Remedy: There is a problem with the Nozzle Config. file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

Code: 23040021

Display: There are no data for "XP-141" in the file.

Used by:

Cause: XP-141 Nozzle Config. information (XP141 specified in NZLCONF/HEADER/TYPE) does not exist.

Remedy: There is a problem with the Nozzle Config. file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

Code: 23040024

Display: The nozzle items "NCFNAME" or "NCFTYPE" do not exist in the file.

Used by:

Cause: The Nozzle Name and Nozzle Type cannot be obtained because either or both of the fields,

"NCFNAME" and "NCFTYPE" are missing from underneath the ["BLOCK","CONFIG+"] field in the XP-141

Nozzle Config. information file (XP141 specified in NZLCONF/HEADER/TYPE).

Remedy: There is a problem with the Nozzle Config. file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

Code: 23040025

Display: A syntax error occurred because the data field count does not agree with the number of nozzle

configuration items.

Used by:

Cause: The item count in the field immediately following the ["BLOCK","CONFIG+"] field in the XP-141

Nozzle Config. information file (XP141 specified in NZLCONF/HEADER/TYPE) does not match the actual

number of items in the fields below that field.

Remedy: There is a problem with the Nozzle Config. file. Normally, the Nozzle Config. file in the MCS-X

default directory is read automatically. Check that the file contains correct data. When starting up the

optimizer, in cases where prompted to specify a file because the default file cannot be found, check the file

contents and correct if necessary.

------------------------------

Code: 23040026

第 2143 页