FUJI错误代码查询.pdf - 第1370页
Cause: Vision processing is not going well (the nozzle is dirty, the parts are not clean), the part is not evenly shaped, or the value in Part data is smaller than the real part. Remedy: If the nozzle and parts are clean…
Display:
Used by:
Cause: There are more than 3 parts where the area to the left and right is not unevenly shaped.
Remedy: Place these parts using Computer Vision #6.
------------------------------
Code: 1D0D0017
Display:
Used by:
Cause: The Y length is too short.
Remedy: Check the part length. Check that Part data is accurate to within +-20%.
------------------------------
Code: 1D0D0018
Display:
Used by:
Cause: The Y length is too long.
Remedy: Check the part length. Check that Part data is accurate to within +-20%.
------------------------------
Code: 1D0D0019
Display:
Used by:
Cause: The X length is too short.
Remedy: Check the part length. Check that Part data is accurate to within +-20%.
------------------------------
Code: 1D0D001A
Display:
Used by:
Cause: The X length is too long.
Remedy: Check the part length. Check that Part data is accurate to within +-20%.
------------------------------
Code: 1D0D001B
Display:
Used by:
Cause: The X length is too long.
Remedy: Check the part length.
------------------------------
Code: 1D0D001C
Display:
Used by:
Cause: The Y length is too short.
Remedy: Check the part length.
------------------------------
Code: 1D0D001D
Display:
Used by:
Cause: Vision processing is not going well (the nozzle is dirty, the parts are not clean), the part is not
evenly shaped, or the value in Part data is smaller than the real part.
Remedy: If the nozzle and parts are clean, check that the parts are not incorrect.
------------------------------
Code: 1D0D001E
Display:
Used by:
第 1369 页
Cause: Vision processing is not going well (the nozzle is dirty, the parts are not clean), the part is not
evenly shaped, or the value in Part data is smaller than the real part.
Remedy: If the nozzle and parts are clean, check that the parts are not incorrect.
------------------------------
Code: 1D0D001F
Display:
Used by:
Cause: Vision processing is not going well (the nozzle is dirty, the parts are not clean), the part is not
evenly shaped, or the value in Part data is smaller than the real part.
Remedy: If the nozzle and parts are clean, check that the parts are not incorrect.
------------------------------
Code: 1D0D0020
Display:
Used by:
Cause: Vision processing is not going well (the nozzle is dirty, the parts are not clean), the part is not
evenly shaped, or the value in Part data is smaller than the real part.
Remedy: If the nozzle and parts are clean, check that the parts are not incorrect.
------------------------------
Code: 1D0D0021
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0022
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0023
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0024
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0025
第 1370 页
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0026
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0027
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0028
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D0029
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D002A
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
uneven. There is foreign matter stuck to the part.
Remedy: Check the camera, vision processing board, cable and focus. Place these parts with Computer
Vision #6. Make sure foreign matter is not stuck to the parts.
------------------------------
Code: 1D0D002B
Display:
Used by:
Cause: Vision processing cannot take a correct part image. The upper and lower parts of the part are too
第 1371 页