FUJI错误代码查询.pdf - 第887页

Code: 12200018 Display: ABS encoder error. Used by: Cause: Failed to recognize the ABS encoder value. It is possible that the SEN signal was not sent normally. Remedy: Check all of the axes encoder wires, and that the SE…

------------------------------

Code: 12200012

Display: Firmware check error.

Used by:

Cause: An error was detected when performing a servo control firmware check, or the servo controller

device driver is corrupted.

Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board

could be damaged.

------------------------------

Code: 12200013

Display: Firmware overwritten.

Used by:

Cause: The servo control firmware has been overwritten. This occurs for certain versions after

immediately upgrading. This error occurs frequently after booting up the machine when the flash memory

is damaged.

Remedy: If this error occurs only one time after upgrading, there is no problem.

If this error occurs frequently, the servo control board could be damaged.

------------------------------

Code: 12200014

Display: Firmware error.

Used by:

Cause: The servo control firmware name is not specified.

It is possible that the servo initialization file is corrupted, an incorrect setting has been specified,

or the servo controller device driver is corrupted

Remedy: Reinstall the recovery media software. If this error cannot be corrected, the hard disk could be

damaged.

------------------------------

Code: 12200015

Display: Linear encoder.

Used by:

Cause: An unexpected error occurred while confirming the linear encoder connection, or the servo

controller device driver is corrupted.

Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board

could be damaged.

------------------------------

Code: 12200016

Display: Linear encoder error.

Used by:

Cause: The linear encoder connection check detected an inappropriate encoder.

Some other encoder is connected to the axis with the linear encoder setting, or the dip switch

setting for the machine is incorrect.

Remedy: Check the connection for the linear encoder. Ensure that the dip switch and amplifier settings

are correct.

------------------------------

Code: 12200017

Display: Initialization failed.

Used by:

Cause: Failed to initialize servo controller access, or the servo controller device driver is corrupted.

Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board

could be damaged.

------------------------------

第 886 页

Code: 12200018

Display: ABS encoder error.

Used by:

Cause: Failed to recognize the ABS encoder value. It is possible that the SEN signal was not sent

normally.

Remedy: Check all of the axes encoder wires, and that the SEN signal is connected properly.

If this cannot be corrected, it is possible that the amplifier is damaged.

------------------------------

Code: 12200019

Display: Abnormal SERCOS communication.

Used by:

Cause: An unidentified node is present in the SERCOS ring. An amplifier dip switch setting is incorrect,

or a servo initialization file setting is incorrect.

Remedy: Check the connections in the SERCOS ring, the amplifier dip switch and rotary switch settings,

and the servo initialization file settings.

------------------------------

Code: 1220001a

Display: Abnormal SERCOS communication.

Used by:

Cause: A node is missing from the SERCOS ring. An amplifier dip switch setting is incorrect, or a servo

initialization file setting is incorrect.

Remedy: Check the connections in the SERCOS ring, the amplifier dip switch and rotary switch settings,

and the servo initialization file settings.

------------------------------

Code: 1220001b

Display: Servo initialization file error.

Used by:

Cause: There is an inappropriate setting in the servo initialization file, or the displayed file is corrupted.

Remedy: After checking the settings, reinstall the recovery media software.

If this error cannot be corrected, the hard disk could be damaged.

------------------------------

Code: 1220001c

Display: A setting is outside the valid range.

Used by:

Cause: A setting in the servo initialization file is outside the valid range, or the displayed file is corrupted.

Remedy: After checking the settings, reinstall the recovery media software.

If this error cannot be corrected, the hard disk could be damaged.

------------------------------

Code: 1220001d

Display: Insufficient working memory.

Used by:

Cause: Either the system resources are insufficient, the operating system is corrupted, or the operating

system installation failed.

Remedy: Reinstall the recovery media software.

If this error cannot be corrected, the hard disk could be damaged.

------------------------------

Code: 1220001e

Display: Parameter setting error.

Used by:

Cause: The sequence order of settings in the servo initialization file is incorrect, or the servo initialization

file is corrupted.

第 887 页

Remedy: After checking the settings, reinstall the recovery media software.

If this error cannot be corrected, the hard disk could be damaged.

------------------------------

Code: 1220001f

Display: Parameter error.

Used by:

Cause: An incorrect parameter is set in the servo initialization file, or the servo initialization file is

corrupted.

Remedy: After checking the settings, reinstall the recovery media software.

If this error cannot be corrected, the hard disk could be damaged.

------------------------------

Code: 12200020

Display: Cannot access a file.

Used by:

Cause: The displayed file is possibly corrupted.

Remedy: After checking the settings, reinstall the recovery media software.

If this error cannot be corrected, the hard disk could be damaged.

------------------------------

Code: 12200021

Display: Program and DLLs do not correspond.

Used by:

Cause: The current program and DLLs are not appropriate, or the installation failed.

Remedy: Reinstall the recovery media software.

If this error cannot be corrected, the hard disk could be damaged.

------------------------------

Code: 12200022

Display: SERCOS communication error.

Used by:

Cause: Communication is not performed if the digital operator was attached when communication

initialization is performed, or the SERCOS drive software version does not match.

Remedy: Disconnect the digital operator and restart the machine, or check the SERCOS drive software

version.

If this error cannot be corrected, the SERCOS drive could be damaged.

------------------------------

Code: 12200023

Display: SERCOS loop disconnected.

Used by:

Cause: The SERCOS loop is disconnected, a fiber optic connector is broken, or the fiber optics are

connected in the wrong order.

Remedy: Check the order of the fiber optic connections, and the condition of the connectors.

If this error cannot be corrected, the SERCOS drive could be damaged.

------------------------------

Code: 12200030

Display: Servo amplifier error.

Used by:

Cause: Parameters are corrupted. Servo pack EEPROM data is abnormal.

Remedy: Replace Servo amplifier with a new one, because the servo amplifier could be damaged.

------------------------------

Code: 12200031

Display: Servo amplifier error.

Used by:

第 888 页