FUJI错误代码查询.pdf - 第1975页
Display: Input file read error Used by: Cause: The input file cannot be read. Remedy: Edit the input file using the editor command. ------------------------------ Code: 21007905 Display: Input file not found Used by: Cau…
comment field of the PST file. The feeder type will be determined based on the Part data
Remedy: Use the editor to edit the PST file, and enter a feeder type in the "Device_name" parameter for the
device number in question.
------------------------------
Code: 2100783E
Display: "Feeder position in PT file is out of range"
Used by:
Cause: A feeder position specified as fixed in the PST file is outside the feeder station range. The device
comment in question will be separated as a non-fixed feeder.
Remedy: Specify a feeder position within the feeder station's range.
------------------------------
Code: 2100783F
Display: "There is insufficient space for a feeder in PT file"
Used by:
Cause: An attempt was made to allocate the feeder in question as specified by the PST file, but an error
occurred when the feeder width was checked against the end of the station. The feeder in question will be
separated as a non-fixed feeder.
Remedy: Change the PST specification number of the feeder in question.
------------------------------
Code: 21007840
Display: "Space between feeders in PT file is insufficient"
Used by:
Cause: An attempt was made to allocate the feeder in question as specified by the PST file, but an error
occurred due to interference between feeders.
Remedy: Change the PST specification number of the feeder in question.
------------------------------
Code: 21007900
Display: Illegal parameter option
Used by:
Cause: An illegal character has been set as a start parameter.
Remedy: Check the start option and then re-start the machine.
------------------------------
Code: 21007901
Display: Message file read error
Used by:
Cause: The message file cannot be read.
Remedy: Re-install the message file.
------------------------------
Code: 21007902
Display: CRT event link error
Used by:
Cause: The CRT event cannot be linked.
Remedy: Reboot the MCS.
------------------------------
Code: 21007903
Display: Input file open error
Used by:
Cause: The input file cannot be opened.
Remedy: Edit the input file using the editor command.
------------------------------
Code: 21007904
第 1974 页
Display: Input file read error
Used by:
Cause: The input file cannot be read.
Remedy: Edit the input file using the editor command.
------------------------------
Code: 21007905
Display: Input file not found
Used by:
Cause: The input file was not found.
Remedy: Check the file name.
------------------------------
Code: 21007906
Display: Output file open error
Used by:
Cause: The space remaining on the hard disk may be insufficient.
Remedy: Delete unnecessary files from the hard disk.
------------------------------
Code: 21007907
Display: Output file write error
Used by:
Cause: The space remaining on the hard disk may be insufficient.
Remedy: Delete unnecessary files from the hard disk.
------------------------------
Code: 21007908
Display: Base program file open error
Used by:
Cause: The base program cannot be opened.
Remedy: Edit the base program using the editor command.
------------------------------
Code: 21007909
Display: Base program file read error
Used by:
Cause: The base program cannot be read. Edit the base program using the editor command.
Remedy: Re_edit the base program.
------------------------------
Code: 2100790A
Display:
Used by:
Cause: Base program file not found.
Remedy: Check the file name.
------------------------------
Code: 2100790B
Display: PST file open error
Used by:
Cause: The permanent set table cannot be opened.
Remedy: Edit the permanent set table using the editor command.
------------------------------
Code: 2100790C
Display: PST file read error
Used by:
Cause: The permanent set table cannot be read.
第 1975 页
Remedy: Edit the permanent set table using the editor command.
------------------------------
Code: 2100790D
Display: PST file not found
Used by:
Cause: Permanent set table not found.
Remedy: Check the file name.
------------------------------
Code: 2100790E
Display: Part data file open error
Used by:
Cause: The Part data file cannot be opened.
Remedy: Edit the Part data file using the editor command.
------------------------------
Code: 2100790F
Display: Part data file read error
Used by:
Cause: The Part data file cannot be read.
Remedy: Edit the Part data file using the editor command.
------------------------------
Code: 21007910
Display: Nozzle assignment table file open error
Used by:
Cause: The nozzle assignment table file cannot be opened.
Remedy: Edit the nozzle assignment table file using the editor command.
------------------------------
Code: 21007911
Display: Nozzle assignment table file read error
Used by:
Cause: The nozzle assignment table file cannot be read.
Remedy: Edit the nozzle assignment table file using the editor command.
------------------------------
Code: 21007912
Display: MTT file open error
Used by:
Cause: The machine type table cannot be opened.
Remedy: Re-install the machine type table.
------------------------------
Code: 21007913
Display: MTT file read error
Used by:
Cause: The machine type table cannot be read.
Remedy: Re-install the machine type table.
------------------------------
Code: 21007914
Display: Pairing data file open error
Used by:
Cause: The pairing data file cannot be opened.
Remedy: Re-install the pairing data file.
------------------------------
Code: 21007915
第 1976 页