FUJI错误代码查询.pdf - 第1897页
Used by: Cause: The name of the output file name exceeds 16 characters. Remedy: Input an output file name within 16 characters. ------------------------------ Code: 21006050 Display: source file read error Used by: Cause…
Code: 21006047
Display: part name specified, but no device comment found
Used by:
Cause: A part name is registered for a component with no registered device comment.
Remedy: Correct the device data for the appropriate source program.
------------------------------
Code: 21006048
Display: device comment specified, but no part name found
Used by:
Cause: A device comment is registered for a component, but no part name.
Remedy: Correct the device data for the appropriate source program.
------------------------------
Code: 21006049
Display: sequence data exceeds maximum allowable sequences
Used by:
Cause: A separated program contains more than the permitted maximum number of sequences.
Remedy: Correct the sequence data for the appropriate source program.
------------------------------
Code: 2100604A
Display: source file undefined
Used by:
Cause: The name of the source program has not been defined.
Remedy: Input the name of the source program.
------------------------------
Code: 2100604B
Display: source file not found
Used by:
Cause: The specified source program does not exist.
Remedy: Check the specified source program name.
------------------------------
Code: 2100604C
Display: source file parmition error
Used by:
Cause: The specified source program is not in the specified partition.
Remedy: Check the specified source program partition.
------------------------------
Code: 2100604D
Display: Off-line Descriptor not found
Used by:
Cause: The specified Off-line Descriptor does not exist.
Remedy: Check the specified Off-line Descriptor.
------------------------------
Code: 2100604E
Display: output file undefined
Used by:
Cause: The output file has not been defined.
Remedy: Input the name of the output file. (The MCS/2 normally handles the output file as a file with the
same name as the source program.)
------------------------------
Code: 2100604F
Display: output file name too long
第 1896 页
Used by:
Cause: The name of the output file name exceeds 16 characters.
Remedy: Input an output file name within 16 characters.
------------------------------
Code: 21006050
Display: source file read error
Used by:
Cause: The source program could not be read.
Remedy: Check the file.
------------------------------
Code: 21006051
Display: special sequence work file create error
Used by:
Cause: The temporary file for special sequences could not be created.
Remedy: If there are no special sequences in the input file, ignore this message. Otherwise, check the
hard disk to ensure that there is enough memory available.
------------------------------
Code: 21006052
Display: output file read error
Used by:
Cause: The output file could not be read.
Remedy: Re-execute the function.
------------------------------
Code: 21006053
Display: output file write error
Used by:
Cause: Data could not be written to the output file.
Remedy: Check how much memory is available on the hard disk.
------------------------------
Code: 21006054
Display: output file open error
Used by:
Cause: The output file could not be opened.
Remedy: Check that the Write protect function has not been set.
------------------------------
Code: 21006055
Display: output file create error
Used by:
Cause: The output file could not be created.
Remedy: Check that the Write protect function has not been set.
------------------------------
Code: 21006056
Display: special sequence work file open error
Used by:
Cause: The temporary file for special sequences could not be opened.
Remedy: If there are special sequences in the program, re-boot MCS.
------------------------------
Code: 21006057
Display: special sequence work file read error
Used by:
Cause: The temporary file for special sequences could not be read.
第 1897 页
Remedy: If there are special sequences in the program, re-boot MCS.
------------------------------
Code: 21006058
Display: special sequence work file write error
Used by:
Cause: Data could not be written to the temporary file for special sequences.
Remedy: If there are special sequences in the program, re-boot MCS.
------------------------------
Code: 21006059
Display: special sequence work file create error
Used by:
Cause: A special sequence temporary file could not be created.
Remedy: If there are special sequences in the program, re-boot MCS.
------------------------------
Code: 2100605A
Display: file open error
Used by:
Cause: Unable to open the input file.
Remedy: Check the filename or the file contents.
------------------------------
Code: 2100605B
Display: file read error
Used by:
Cause: A file could not be read.
Remedy: Check the file and save it.
------------------------------
Code: 2100605C
Display: file write error
Used by:
Cause: A file could not be written to.
Remedy: Check that there are no write protect settings in effect. Otherwise, check the hard disk to ensure
that there is enough memory available. If not, eliminate unnecessary files or perform maintenance on the
hard disk.
------------------------------
Code: 2100605D
Display: generator command fork error
Used by:
Cause: The glue program generator could not be booted up.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
------------------------------
Code: 2100605E
Display: ls command fork error
Used by:
Cause: The ls command could not be booted.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
------------------------------
Code: 2100605F
Display: err_disp command fork error
Used by:
Cause: The error displays could not be booted.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
第 1898 页