FUJI错误代码查询.pdf - 第1357页
------------------------------ Code: 1D0C4001 Display: Used by: Cause: The part boundary could not be found. Remedy: Check the part shape, and the image. ------------------------------ Code: 1D0C4006 Display: Used by: Ca…
Cause: When searching for a bright area after a lead, more than half the body was searched but a bright
area was not found.
Remedy: Check the body size and direction as entered in Part data (PDG).
------------------------------
Code: 1D0C001A
Display: 0026
Used by:
Cause: When the bumper was recognized the leads were searched for from the center and a range error
occurred.
Remedy: None.
------------------------------
Code: 1D0C001B
Display: 0027
Used by:
Cause: The lead could not be found because the part was tilted or some related reason.
Remedy: Check that the machine is picking parts correctly.
------------------------------
Code: 1D0C001C
Display: 0028
Used by:
Cause: The lead could not be found because the part was tilted or some related reason.
Remedy: Check that the machine is picking parts correctly.
------------------------------
Code: 1D0C001D
Display: 0029
Used by:
Cause: A range error occurred during vision processing and the operation was cancelled.
Remedy: Check that the nozzle is clean, that no foreign matter is stuck to the part, and that the part itself
is the correct one.
------------------------------
Code: 1D0C001F
Display: 0031
Used by:
Cause: There are more leads on the part than the number entered in Part data (PDG).
Remedy: Check the number of leads entered in Part data (PDG), the direction, and lead information.
Check the orientation of the part as it is fed into the machine.
------------------------------
Code: 1D0C0020
Display: 0032
Used by:
Cause: The edge cannot be found.
Remedy: Check the number of leads entered in Part data (PDG), the direction, and lead information.
Check the orientation of the part as it is fed into the machine.
------------------------------
Code: 1D0C0021
Display: 0033
Used by:
Cause: A lead could not be found by searching 1/3 of the body, but when vision processing started again
a range error occurred.
Remedy: Check the number of leads entered in Part data (PDG), the direction, and lead information.
Check the orientation of the part as it is fed into the machine.
第 1356 页
------------------------------
Code: 1D0C4001
Display:
Used by:
Cause: The part boundary could not be found.
Remedy: Check the part shape, and the image.
------------------------------
Code: 1D0C4006
Display:
Used by:
Cause: The part is tilted too much.
Remedy: Check the part shape and check that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C4007
Display:
Used by:
Cause: The part boundary could not be found.
Remedy: Check the part shape and check that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C4008
Display:
Used by:
Cause: There are fewer than two leads in the upper or lower area of the part.
Remedy: When using Vision #12 there must be at least 2 leads in one area. When this is not the case,
use another vision number.
------------------------------
Code: 1D0C4009
Display:
Used by:
Cause: The part boundary could not be found.
Remedy: Check the part shape and check that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C400A
Display:
Used by:
Cause: The part boundary could not be found.
Remedy: Check the part shape and check that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C400B
Display:
Used by:
Cause: The first lead could not be found in each area.
Remedy: Check the lead width, the orientation of the parts as they are fed into the machine and check
that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C400C
Display:
Used by:
Cause: The first lead could not be found in each area.
Remedy: Check the lead width, the orientation of the parts as they are fed into the machine and check
that the vision processing system is taking the image correctly.
第 1357 页
------------------------------
Code: 1D0C400D
Display:
Used by:
Cause: The lead pitch is too wide and/or the lead width is too wide.
Remedy: Check the part.
------------------------------
Code: 1D0C400E
Display:
Used by:
Cause: A missing or broken lead was encountered during vision processing.
Remedy: Check the lead pitch and the orientation of the part.
------------------------------
Code: 1D0C400F
Display:
Used by:
Cause: The lead pitch exceeds the permissible range.
Remedy: Check the shape of the part.
------------------------------
Code: 1D0C4010
Display:
Used by:
Cause: The part boundary could not be found.
Remedy: Check the part shape and check that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C4011
Display:
Used by:
Cause: The part boundary could not be found.
Remedy: Check the part shape and check that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C4012
Display:
Used by:
Cause: The part boundary could not be found.
Remedy: Check the part shape and check that the vision processing system is taking the image correctly.
------------------------------
Code: 1D0C4016
Display:
Used by:
Cause: The lead could not be found.
Remedy: Check the part size and orientation.
------------------------------
Code: 1D0C4019
Display:
Used by:
Cause: The lead could not be found.
Remedy: Check the part size and orientation.
------------------------------
Code: 1D0C401B
Display:
第 1358 页