FUJI错误代码查询.pdf - 第587页

Cause: A cleaner interlock occurred when the cleaner drive axis (the Y-axis for a double-side cleaner, or the S-axis for a single-side cleaner) was activated. This error occurs if the cleaner drive axis is activated whil…

CHK shows a value of 0).

------------------------------

Code: 1205610F

Display: Interlock (Z|Y) Conveyor Width Clutch

Used by: GP551,GP6

Cause: The displayed axis and the conveyor width clutch may collide.This error occurs when the

conveyor width clutch is engaged while the displayed axis is in motion.

Remedy: Disengage the conveyor width clutch. Alternatively, check the on/off status of the conveyor

width clutch's engaged/disengaged sensors.

------------------------------

Code: 12056110

Display: 联锁Ｚ轴相机

[Interlock Ｚaxis Camera]

Used by: GP551,GP6,GPX,NXTP

Cause: Ｚ轴与相机有可能发生了干涉。在Ｚ轴移动时相机不在待机位置的情况下发生。

Remedy: 请将相机移动到待机位置。或者，请确认相机的待机位置确认传感器的ON/OFF动作。

------------------------------

Code: 12056111

Display: Interlock Z axis Cleaner

Used by: GP551,GP6

Cause: The Z-axis and the lower cleaner may collide.This error occurs when the lower cleaner is not at its

origin position and the Z-axis is in motion. On the GP-6, this error occurs when the cleaner shift is not at

its retract position while the Z-axis is in motion.

Remedy: Move the lower cleaner to its origin position. On the GP-6, for one-sided cleaners, move the

cleaner shift to it retract position. Alternatively, check the on/off status of the sensors at the cleaner

origin position and, on the GP-6, the cleaner shift retract position.

------------------------------

Code: 12056112

Display: Interlock SSD axis Cylinder

Used by: GP551,GP6

Cause: The solder supply syringe which is joined to the SSD-axis may collide with another part. This

error occurs when the solder supply syringe is down and an attempt is made to move the SSD-axis.

Remedy: Raise the solder supply syringe. Alternatively, check the on/off status of the up/down sensors

on the syringe.

------------------------------

Code: 12056113

Display: "Please Camera escape"

Used by: GP551,GP6

Cause: The camera (X-axis) and the Z-axis are in an interference zone with respect to each other, or are

interfering with each other. This error occurs if the holder is changed while neither the camera (X-axis) nor

the Z-axis are at their respective escape positions.

Remedy: Move the Z-axis to the Z-axis escape position (the position at which X03C:Z ESC POS CHK

shows a value of 0), or move the camera (X-axis) to its escape position (the position at which X03D:X ESC

POS CHK shows a value of 0). If necessary, make sure that the Z-axis/camera interference prevention

interlock sensor and the X-axis camera escape position check sensor (X03C:Z ESC POS CHK and X03D:X

ESC POS CHK) are functioning normally.

------------------------------

Code: 12056114

Display: "Cleaner Is Engaged"

Used by: GP6

第 586 页

Cause: A cleaner interlock occurred when the cleaner drive axis (the Y-axis for a double-side cleaner, or

the S-axis for a single-side cleaner) was activated. This error occurs if the cleaner drive axis is activated

while the cleaner is connected to the drive axis during command execution or automatic operation.

Remedy: Use [HEAD REMOVAL] on command page 553-2(3) to disconnect the cleaner from the drive axis

(the Y-axis for a double-side cleaner, or the S-axis for a single-side cleaner). If necessary, make sure that

the lower cleaner connection check sensor and the cleaner connection position proximity check sensor

(X05D:LW CLR CPL CHK and X03E:CLNR NEAR CHK) are functioning normally.

------------------------------

Code: 12056115

Display: "Solder Unit Off Origin"

Used by: GP551,GP6

Cause: A solder supply unit interlock occurred when the S-axis was activated. This error occurs if the S-

axis is activated while the solder supply unit is not at the origin position during command execution or

automatic operation.

Remedy: Use [ESCAPE POSITION MOVEMENT] on command page 544(4) to move the solder supply unit

to the original position. If necessary, make sure that the solder supply unit origin position check sensor

(1108:SSD ZERO POS) is functioning normally.

------------------------------

Code: 12056116

Display: "Interlock Cleaner Z"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the Z-axis is not at the origin position.

Remedy: Move the Z-axis to the Z-axis escape position (the position at which "X03C:Z ESC POS CHK

shows a value of 0). If necessary, make sure that the Z-axis camera interference prevention

interlocksensor (X03C:Z ESC POS CHK) is functioning normally.

------------------------------

Code: 12056117

Display: "Interlock Cleaner X"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the X-axis is not at the origin position.

Remedy: Use [CAMERA ESCAPE] on command page 550(2) to move the X-axis to the X-axis escape

position (the position at which X03D:X ESC POS CHK shows a value of 0). If necessary, make sure that

the X-axis camera interference prevention interlock sensor (X03D:X ESC POS CHK) is functioning

normally.

------------------------------

Code: 12056118

Display: "Interlock Cleaner SSD"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the SSD-axis is not at the origin

position.

Remedy: Use [ESCAPE POSITION MOVEMENT] on command page 544(4) to move the SSD-axis to the

SSD-axis escape position (the position at which 1108:SSD ZERO POS shows a value of 0). If necessary,

make sure that the solder supply unit origin position check sensor (1108:SSD ZERO POS) is functioning

normally.

------------------------------

Code: 12056119

Display: "Interlock Cleaner Holder Down"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the squeegee holder is down.

Remedy: Raise the squeegee (set Y02F:SQG HLDR UP to 0). If necessary, make sure that the squeegee

holder upper limit check sensor (X070:SQG HLDR UP) is functioning normally.

第 587 页

------------------------------

Code: 1205611A

Display: "Interlock Cleaner F Holder Up"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the front squeegee holder is down.

Remedy: Raise the front squeegee (set Y01D:F SQG HLDR UP to 0). If necessary, make sure that the front

squeegee holder upper limit check sensor (X070:F SQG HLDR UP) is functioning normally.

------------------------------

Code: 1205611B

Display: "Interlock Cleaner R Holder Up"

Used by: GP6

Cause: This error occurs if a cleaner command is executed while the rear squeegee holder is down.

Remedy: Raise the rear squeegee (set Y02F:R SQG HLDR UP to 0). If necessary, make sure that the rear

squeegee holder upper limit check sensor (X078:R SQG HLDR UP) is functioning normally.

------------------------------

Code: 1205611C

Display: "Interlock Conveyor Width Clutch"

Used by: GP6

Cause: The conveyor width clutch was turned on during automatic operation. This error occurs if the

conveyor width clutch turns on and interferes with the Z-axis during automatic operation.

Remedy: Use [UNLOCK] on command page 300(5)(1) to turn the conveyor width clutch off.If necessary,

make sure that the left and right conveyor width notch limit check sensors (X035:W_CLUTCH1_OFF

andX037:W_CLUTCH2_OFF) are functioning normally.

------------------------------

Code: 1205611D

Display: "Interlock Cleaner Connected"

Used by: GP6

Cause: The cleaner is interfering with the S-axis. This error occurs if the cleaner is connected to the S-

axis when the S-axis is moved to the printing position during automatic operation.

Remedy: Use [HEAD REMOVAL] on command page 553-2(3) to disconnect the cleaner from the S-axis. If

necessary, make sure that the lower cleaner connection check sensor, the cleaner connection

positionproximity check sensor, and the lower cleaner origin position check sensors (X05D:LW CLR CPL

CHK, X03E:CLNR NEAR CHK, and X05C:CLNR ZERO POS) are functioning normally.

------------------------------

Code: 1205611E

Display: 请待机Ｚ轴

[Z escape]

Used by: GP6,GPX

Cause: Ｚ轴与清洁器(移位)发生干涉。在清洁动作的清洁器移位前进时Ｚ轴不在待机位置的情况下发生。存在清洁

器和主工作台发生了干涉的可能性。 (GPX)

Remedy: 请将Ｚ轴移动到Ｚ轴待机位置(X03C:Z ESC POS CHK 为O的位置)。或者，请确认Ｚ轴相机干涉防止联锁

传感器(X03C:Z ESC POS CHK)。 1.虽然稍重但是请用手将清洁器移动至退避位置。

2.发生了干涉时，请与本公司的Support联系。（GPX)

------------------------------

Code: 1205611F

Display: "Move upper cleaner to escape position."

Used by: GP551

Cause: The upper cleaner is not at the escape position.

Remedy: Move the upper cleaner to the escape position.

------------------------------

第 588 页