FUJI错误代码查询.pdf - 第84页

请确认元件数据的「Body Length(X)」、「Body Width(Y)」。 请确认元件数据的「Element」。 ------------------------------ Code: 1101D000 Display: Used by: CP5 Cause: The nozzles set in Part data in the production program are not in the nozzle allocat…

100%1 / 5282
Code: 1101C714
Display: 在顺序号**和**上参考记号（注解）重复。
Used by: XP142,XP242
Cause: 子电路板No.0的顺序和其他的顺序上参考记号（注解）重复。
Remedy: 请变更参考记号（注解）以使其不要重复。
------------------------------
Code: 1101C715
Display: 不存在被指定的供料平台No./料站No.。
Used by: XP142
Cause: 不存在被指定的供料平台No./料站No.。供料平台No.或者料站No.中有错误。
Remedy: 请确认供料平台No.和料站No.。
------------------------------
Code: 1101C716
Display: 生产中所必需的吸嘴没有存放在吸嘴存储器中。
Used by: XP142,XP143
Cause: 因为生产中所需要的吸嘴超过了36根，所以不能收存在吸嘴存储器中。
Remedy: 请重新检查吸嘴头No.、顺序以及初期的吸嘴配置。
------------------------------
Code: 1101C717
Display: 在执行顺序时的工作头的吸嘴配置上不能吸取元件。
Used by: XP142,XP143
Cause: 在执行顺序时，在工作头内不存在可以吸取的吸嘴或者与其他的吸嘴有干扰而不能吸取。
Remedy: 要更换吸嘴进行生产时，请在吸嘴头No.中指定0以外的数字。
不更换吸嘴进行生产时，请用合适的吸嘴设定吸嘴数据。
------------------------------
Code: 1101C718
Display: 只有在吸嘴头No.**上才能贴装。
Used by: XP142,XP143
Cause: 在所指定的吸嘴头No.上不能贴装。
Remedy: 请变更吸嘴头No.。
------------------------------
Code: 1101C719
Display: 在设定为同一个元件数据的供料器上，同时存在0和1的供料器设定。
Used by: XP142,XP242,XP143,XP243
Cause: 在指定设定为同一个元件数据的供料器的顺序数据上，同时存在供料器跳过0和1时，不能保存Job。
Remedy: 在指定设定为同一个元件数据的供料器的顺序数据的供料器跳过时请全部进行相同的设定。
或者，请保存生产程序(Recipe)。
------------------------------
Code: 1101C71A
Display: 贴装位置不正确。
Used by: XP142,XP143,XP242,XP243
Cause: 贴装位置不正确。
元件完全超出X方向的贴装范围或者元件的一部分超出Y方向的贴装范围。
贴装范围是除去压住搬运轨道部分的电路板上面。
Remedy: 请确认贴装位置和元件尺寸。
请确认电路板数据的「电路板尺寸X」、「电路板尺寸Y」。
请确认电路板数据的「修正值X」、「修正值Y」。
请确认顺序数据的「X坐标」、「Y坐标」。
请确认顺序数据的「角度」。
请确认元件数据的「Direction」。
请确认元件数据的「Placing Offset X」、「Placing Offset Y」。
第 83 页
请确认元件数据的「Body Length(X)」、「Body Width(Y)」。
请确认元件数据的「Element」。
------------------------------
Code: 1101D000
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 1~13 on the CP4 and CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D001
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 14~26 on the CP4 and 14~27 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D002
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 27~39 on the CP4 and 28~41 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D003
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 40~52 on the CP4 and 42~55 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D004
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 53~65 on the CP4 and 56~69 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D005
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 66~78 on the CP4 and 70~83 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
第 84 页
Code: 1101D006
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 79~91 on the CP4 and 84~97 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D007
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 92~104 on the CP4 and 98~111 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D008
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 105~117 on the CP4 and 112~125 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D009
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 118~130 on the CP4 and 126~139 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D00A
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 131~140 on the CP4 and 140~153 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D00B
Display:
Used by: CP5
Cause: The nozzles set in Part data in the production program are not in the nozzle allocation table
(devices 154~167 on the CP5).
Remedy: Check the appropriate devices for the correct size, alter the Part data or the nozzle allocation
table, and transmit the program.
------------------------------
Code: 1101D00C
Display:
Used by: CP5
第 85 页