FUJI错误代码查询.pdf - 第128页

Cause: The solder supply speed setting is outside the valid range. Remedy: Make sure that the solder supply speed setting in the production program is from 0 to 200 [mm/sec]. If a value of 0 has been set in the productio…

Remedy: Set the indexing type in the program header to one of the following values: 0, 2, 3, 4, or 5. These

settings indicate 7-inch indexing, 5-2 indexing, 4-3 indexing, 3-4 indexing, and 2-5 indexing, respectively.

------------------------------

Code: 1101E02E

Display: Same as code

Used by: QP132

Cause: Different indexing types are specified for programs having the same family name.

Remedy: Change the family name, or set the indexing types to the same value.

------------------------------

Code: 1101E02F

Display: Same as code

Used by: QP132

Cause: Unexecutable sequences have occurred because the indexing type in the program header has

been set to 7-inch single indexing. This error occurs when the program is checked upon transmission.

Remedy: Check the mounting coordinates in the sequence data. If the coordinates are correct, set the

indexing type in the program header to a value other than 0.

------------------------------

Code: 1101E030

Display: Same as code

Used by: QP132

Cause: A family name has not been set in the program header. This error occurs when the program is

checked upon transmission.

Remedy: Set a family name in the program header.

------------------------------

Code: 1101E031

Display: Same as Code.

Used by: QP132

Cause: The value set for the loading distance position for tandem loading ("PCB distance") has been set to

a positive value.

Remedy: Set this item to a negative value.

------------------------------

Code: 1101E032

Display: 与编码相同

Used by: GP551,GP6,GPX,NXTP

Cause: 特殊清洁计数器超出范围。

Remedy: 请确认生产程序的Ｓｐｅｃｉａｌ＿ｃｌｅａｎｉｎｇ＿ｉｎｔｅｒｖａｌ。

范围:0～65000［块］

请确认FujiFlexa上设定的特殊自动清洁计数器。

范围:0～9999[块](GPX,NXTP)

自动清洁为0块时，不能对特殊清洁进行1块以上的设定(GPX,NXTP)。

------------------------------

Code: 1101E033

Display: Same as code

Used by: GP2,GP3,GP551,GP6

Cause: The pressure measurement interval setting is outside the valid range.

Remedy: Make sure that the "Press_meas_interval" parameter in the production program is set to a value

from 0 to 65000 [boards].

------------------------------

Code: 1101E034

Display: Same as code

Used by: GP551,GP6

第 127 页

Cause: The solder supply speed setting is outside the valid range.

Remedy: Make sure that the solder supply speed setting in the production program is from 0 to 200

[mm/sec]. If a value of 0 has been set in the production program, check the solder supply speed setting in

the Proper data.

------------------------------

Code: 1101E035

Display: Same as code

Used by: GP2,GP3,GP551,GP6

Cause: Squeegee/Pressure Rear, Squeegee/Pressure Front, or Squeegee/Solder Low Limit at the

production program is out of range.

Remedy: Verify the data input range for the production program.

Squeegee/Pressure Rear: 0.10 to 9.99

Squeegee/Pressure Front: 0.10 to 9.99

Squeegee/Solder Low Limit: -9.99 to -0.10

The following are the ranges at machines with a max. print pressure of 20-kg.

Squeegee/Pressure Rear: 0.10 to 20.0

Squeegee/Pressure Front: 0.10 to 20.0

------------------------------

Code: 1101E036

Display: Same as code

Used by:

Cause: The value specified at the item "Solder_supply_stroke" in the production program is outside the

acceptable range.

Remedy: Check the value set in item "Solder_supply_stroke" of the production program. The acceptable

range is 1-510 [mm]. (For GP-6 single squeegee machines the acceptable range is 1-420 [mm] and for

double squeegee machines the acceptable range is 1-460 [mm]. For GP-5 single squeegee machines the

acceptable range is 1-320 [mm] and for double squeegee machines the acceptable range is 1-360 [mm].)

------------------------------

Code: 1101E037

Display: Same as code.

Used by:

Cause: Size_x and Size_y values have not been set in mark data despite the fact that the production

program contains block skip marks.

Remedy: Retransmit the program after setting the Size_ x and Size_y values in mark data.

------------------------------

Code: 1101E038

Display: 与该编码相同

Used by: GP551,GP6,GPX,NXTP

Cause: 生产程序的Screen Status为规定外。

网版类型为范围外。(GPX,NXTP)

Remedy: 请确认生产程序的数据Screen Status。

GP6的框设定如下所示。

新FUJI框：0000 0000 0000 0001 (1H)

其他公司框／旧FUJI框网版更换完毕：0000 0000 0000 0000 (0H)

旧FUJI框网版无更换：0000 0000 0000 1000 (8H)

可以设定的网版类型如下所示。

·0:650x680mm

·1:550x650mm(GP6框,NXTP-M35)

·2:650x550mm

·3:23英寸四方形

·4:29英寸四方形

第 128 页

·5:450x450mm(GPX,NXTP-M25)

·9:550x600mm(NXTP-M35)

------------------------------

Code: 1101E039

Display: Index motion type error.

Used by: QP132

Cause: The index motion type is out of range. The index motion type depends on the size of the pallet.

For example, with an 8 inch pallet, any value besides, "8", "35", "44" and "53" results in an error.

Remedy: If this error occurs when the production program is transmitted, enter the correct value for

"Index_motion" in the production program.

------------------------------

Code: 1101E03A

Display: Wrong family condition

Used by: QP132

Cause: A different-family program was transmitted to the foreground while boards were in the machine.

Remedy: Do not transmit different-family programs to the foreground when boards are in the machine.

Check the program's family name.

------------------------------

Code: 1101E03B

Display: Wrong family condition

Used by: QP132

Cause: Wrong family condition.

Remedy: Check the family condition.

------------------------------

Code: 1101E03C

Display: Wrong tandem program condition

Used by: QP132

Cause: Wrong tandem program condition.

Remedy: Check the tandem program setting.

------------------------------

Code: 1101E03D

Display: Wrong index motion type

Used by: QP132

Cause: An index motion type of "8" ("88" at 16-inch pallets) was designated at a program where single

indexing production is impossible due to the placing coordinate configuration.

Remedy: Change the index motion type.

------------------------------

Code: 1101E03E

Display: 与编码相同

Used by: CP643, GPX,NXTP

Cause: 电路板厚度在范围之外

Remedy: 请确认生产程序的Pcb_Thickness(MCS时)。请确认生产程序的General PCB Data Thickness(Ｆ４Ｇ时

)的数值。如果是ＣＰ６４３，由于贴装吸嘴的基准是按照电路板下面被测定的，因此必须输入电路板厚度。范围是

０．３０～４．００［ｍｍ］。

范围为０．４ｍｍ～６。０ｍｍ。（GPX,NXTP）

------------------------------

Code: 1101E03F

Display: same as code.

Used by: CP643

Cause: The clearance between boards is less than 15 mm.

Remedy: Set the item "PCB_DISTANCE" equal to the item "Pcb_X" plus 15 mm or more. The item

第 129 页