FUJI错误代码查询.pdf - 第584页

------------------------------ Code: 12056103 Display: Vacuum Holder Too Large Used by: GP551,GP6 Cause: The size of the board vacuum holder does not match the conveyor width. If the Z-axis is raised under this condition…

Remedy: 请取得发生错误时的跟踪数据，与本公司电话服务中心联络。

------------------------------

Code: 12056058

Display: 机内无电路板

Used by: NXTP

Cause: 执行机内(主搬运轨道)电路板的使用指令时没有发现电路板。

Remedy: 请打开门并放入电路板。

------------------------------

Code: 12056059

Display: 主搬运轨道的换乘传感器异常

Used by: GPX-C

Cause: 1.用于检测换乘过程的传感器未检测出搬运中的电路板，但是用于检测抵达的传感器发生感应了

2.换乘传感器的调试不良

3.抵达传感器误将电路板以外的零部件等（例.电路板挡块）当作电路板发生感应了

Remedy: 1.如果搬运轨道内有电路板，则请对换乘传感器进行调整

2.如果搬运轨道内没有电路板，则请对抵达传感器进行调整

------------------------------

Code: 1205605A

Display:

Used by:

Cause:

Remedy:

------------------------------

Code: 1205605B

Display:

Used by:

Cause:

Remedy:

------------------------------

Code: 1205605C

Display:

Used by:

Cause:

Remedy:

------------------------------

Code: 12056101

Display: Interlock X Tramsfer

Used by:

Cause: Movement of the frame in the X direction may be interfering with the manual cleaning lifter or the

S axis.

Remedy: If it is the manual cleaning lifter, move the frame to the left or to the right and then re-execute

the command. If it is the S axis, move the screen to the left and then re-execute the command.

------------------------------

Code: 12056102

Display: Interlock Screen Lift

Used by:

Cause: The manual cleaning lifter may be interfering with X direction movement of the frame or the S

axis.

Remedy: After moving the manual cleaning lifter to its down position, re-execute the command.

第 583 页

------------------------------

Code: 12056103

Display: Vacuum Holder Too Large

Used by: GP551,GP6

Cause: The size of the board vacuum holder does not match the conveyor width. If the Z-axis is raised

under this condition the conveyor belt will be in danger of being cut.

Remedy: Replace the vacuum holder with one that matches the size of the conveyor width. On the GP6

use the X048 and X049 input signals for verification.

------------------------------

Code: 12056104

Display: 联锁相机Ｚ轴

[Interlock Camera Ｚaxis]

Used by: GP551,GP6,GPX

Cause: 相机与Ｚ轴有可能发生了干涉。在相机移动时Ｚ轴不在待机位置的情况下发生。

Remedy: 请将Ｚ轴移动到待机位置。或者，请确认Ｚ轴待机位置确认传感器的ON/OFF动作。

------------------------------

Code: 12056105

Display: 联锁相机主挡块

[Interlock Camera Main Stopper]

Used by: GP551,GP6,GPX,NXTP

Cause: 安装在相机上的主挡块有可能与其他的部分发生干涉。在下降了主挡块后想要移动相机的情况下发生。

Remedy: 请上升主挡块。或者，请确认ＭＡＩＮ搬运轨道挡块的导入端·退出端的各确认传感器的ON/OFF动作。

------------------------------

Code: 12056106

Display: Interlock Camera Push Plate

Used by: GP551,GP6

Cause: The push plate, attached to the camera, may be damaged in a collision if the push plate is down

and an attempt is made to move the camera.

Remedy: Raise the push plate.Alternatively, check the on/off status of the push plate's up/down position

sensors.

------------------------------

Code: 12056107

Display: InterlockCamera Cleaner

Used by: GP551,GP6

Cause: The camera may collide with the lower cleaner. For GP-5 machines this may occur when the

lower cleaner is not at the origin position. For GP-6 machines, this may occur when the cleaner shift is not

at the retract position.

Remedy: Move the lower cleaner to its origin position (GP-5).For one-sided cleaners, move the cleaner shift

to its retract position (GP-6).Alternatively, check the on/off status of the lower cleaner origin position

sensor, camera and lower cleaner proximity sensor, and the cleaner shift retracted position sensor.

------------------------------

Code: 12056108

Display: Interlock Camera Cleaner Head

Used by: GP551,GP6

Cause: The cleaner head on the cleaner axis may collide with another part. This error occurs if an

attempt is made to move the cleaner axis when the cleaner head is closed.

Remedy: Open the cleaning head. Alternatively, check the on/off status of the cleaner's raised/lowered

sensors (GP-5) or the cleaning head's opened/closed sensors (GP-6).

------------------------------

第 584 页

Code: 12056109

Display: Interlock S axis SGQ Holder

Used by: GP551,GP6

Cause: The squeegee holder on the S-axis may collide with another part. This error occurs if an attempt

is made to move the S-axis when the squeegee holder is down.

Remedy: Raise the squeegee holder. Alternatively, check the on/off status of the squeegee holder's

raised/lowered position sensors.

------------------------------

Code: 1205610A

Display: "Interlock S axis Cleaner Head"

Used by: GP6

Cause: The S-axis cleaner head and another part are in an interference zone with respect to each other,

or are interfering with each other. This error occurs when an attempt is made to move the S-axis while

the cleaner head is closed.

Remedy: Open the cleaner head (set Y020:LW CLNR OPEN or Y021:TP CLNR OPEN to 0). If necessary,

make sure that the lower and upper cleaner head open limit check sensors (X05A:LW CLR OPN CHK and

X07C:TP CLR OPN CHK) are functioning normally.

------------------------------

Code: 1205610B

Display: "Interlock S axis Supply Solder"

Used by: GP551,GP6

Cause: The solder supplier (SSD-axis) may interfere with the S-axis.This error occurs if the S-axis is

moved while the solder supplier (SSD-axis) is not at the escape position.

Remedy: Move the solder supplier (SSD-axis) to the escape position. If necessary, make sure that the

SSD-axis escape position check sensor is functioning normally.

------------------------------

Code: 1205610C

Display: Interlock S axis Cleaner

Used by: GP551,GP6

Cause: The S-axis may collide with the top cleaner. For GP-5 machines, this error occurs when the top

cleaner is not at its origin position and an attempt is made to move the S-axis. For GP-6 machines, this

error occurs when the notch on a cleaner not joined to the S-axis is engaged and the S-axis is moving.

Remedy: Move the top cleaner to its origin position (GP-5). Disengage the cleaner's notch (GP-6).

Alternatively, check the on/off status of the top cleaner's origin position sensor (GP-5) or the lower

cleaner's joining sensor (GP-6).

------------------------------

Code: 1205610D

Display: Interlock Cleaner Z axis

Used by: GP551,GP6

Cause: The lower cleaner and the Z-axis may collide.This error occurs when the Z-axis is not at the

retract position and the cleaner, joined to its driving axis, is in motion.

Remedy: Move the Z-axis to its retract position. Alternatively, check the on/off status of the Z-axis'

retract position sensor.

------------------------------

Code: 1205610E

Display: "Interlock Cleaner Camera"

Used by: GP6

Cause: The camera (X-axis) is in an interference zone with respect to the cleaner, or is interfering with it.

This error occurs if the cleaner (connected to the S-axis) is moved while the camera (X-axis) is not at the

escape position.

Remedy: Move the X-axis to the X-axis camera escape position (the position at which X03D:X ESC POS

第 585 页